• Journal of Biosystems Engineering
• /
• v.35 no.6
• /
• pp.408-412
• /
• 2010

Rheological properties of cereals such as rye are great important for the design of die for extrusion and the development of models for extrusion process. Therefore, this study was carried out to analyze the rheological properties according to moisture content of rye flour and extrusion temperature. Rheological properties of rye flour were investigated by using a capillary rheometer for moisture content of three levels (30, 35, 40%) and extrusion temperature of three levels (120, 130, $140^{\circ}C$). Determination coefficients for the relationship between apparent shear stress ($\tau_{ap}$) and apparent shear velocity ($\gamma_{ap}$) were relatively high in the range of 0.973 ~ 0.997 under each extrusion condition. The values of consistency index (K) was decreased with increasing moisture content and extrusion temperature. However, the value of flow behavior index (n) presented the highest value at moisture content of 35%, but it was not affected by extrusion temperature.

• Food Science and Biotechnology
• /
• v.17 no.2
• /
• pp.319-323
• /
• 2008

Mutant rice cv. Goami2 (G2) and Baegjinjoo (BJJ) derived from a high-quality japonica rice cv. Ilpumbyeo (IP) were extruded under different feed moisture (20 and 30%) and barrel temperature (90, 110, and $130^{\circ}C$). Increasing feed moisture at fixed barrel temperature increased extrudate density (ED) in IP and BJJ. Whereas, G2 showed a varied ED depending on extrusion conditions; increasing barrel temperature decreased the ED of G2 extrudate with low feed moisture, but increased with high moisture. Results indicated a positive barrcl temperature effect on volume expansion in IP and G2, but a negative effect on 811, probably due to shrinkage of expanded products containing low-amylose contents. A significant increase of water absorption was found in G2 and BJJ extruded flour, while an increase of water solubility in those from IP. Non-digestible carbohydrates measured by total dietary fiber (TDF) indicated that extrusion increased slightly TDF in IP and BJJ extrudates, but decreased in G2 products, which might be variety-dependent.

• Korean Journal of Food Science and Technology
• /
• v.29 no.1
• /
• pp.72-76
• /
• 1997

The effect of the energy supplied in extrusion on the starch gelatinization was analyzed. The energy needed for extrusion is generated by motor and heater. The motor energy is transformed into a thermal energy by heat dissipation and a mechanical energy, and the heater energy is of a thermal energy. At the low barrel temperature $({\leq}80^{\circ}C)$, it was found out there are two kinds of thermal energy by heat dissipation: one by a powder friction of corn grit with low moisture contents and the other by a viscous dissipation of corn grit with high moisture contents. The dissipated thermal energy by the powder friction was more effective on the starch gelatinization than that by the viscous dissipation. The effect of the mechanical energy was also analyzed in terms of a relative mechanical energy. The gelatinization of corn grit with high moisture contents $({\geq}33%)$ largely depended on the change in the relative mechanical energy, whereas that with low moisture contents $({\leq}30%)$ hardly depended on it.

• Korean Journal of Food Science and Technology
• /
• v.52 no.4
• /
• pp.357-362
• /
• 2020

This study was conducted to investigate the effects of mushroom composition (0, 4, 8, and 12%) on the quality characteristics of an extruded meat analog. The meat analog blend was isolated soy protein, wheat gluten, and corn starch (50:40:10). The extrusion condition was set to 55% feed moisture, 170℃ barrel temperature, and 150 screw speed by high moisture extrusion using a twin-screw extruder equipped with a cooling die. The integrity index, hardness, cohesiveness, springiness, chewiness, and cutting strength of the meat analog increased with the increasing mushroom content, while its water holding capacity and nitrogen solubility index (NSI) decreased. The protein digestibility decreased with the increasing mushroom content, while the DPPH radical scavenging activity significantly increased. In conclusion, the incorporation of mushrooms into the investigated meat analog enhanced its texture and antioxidant level.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.9
• /
• pp.1407-1414
• /
• 2014

Physicochemical properties of rice-based expanded snacks extruded with rice flour, high amylose starch, and isolated soy protein were investigated using a twin-screw extruder. The ingredients were extruded at various feed moisture contents (19~23%) and screw speeds (200~400 rpm) at a constant feed rate (43.4 kg/hr). Bulk density and apparent density of rice snacks were 0.06~0.21, and 0.55~0.65 respectively. Bulk density, apparent density, water absorption index, and breaking strength of rice snacks increased with increasing feed moisture content and decreasing screw speed. However, expansion and water solubility index of rice snacks increased with decreasing feed moisture content and increasing screw speed. Hunter's color L values of rice snacks was lower with increasing screw speed at feed moisture contents of 19% and 21%, but was not significantly different from a feed moisture content of 23%. On the other hand, a and b values of rice snacks were higher with increasing screw speed a feed moisture content of 19%. X-ray diffraction intensity of rice snacks decreased with decreasing feed moisture content and increasing screw speed. X-ray diffraction of rice snacks was V-type at feed moisture contents of 19% and 21% and screw speeds of 300, and 400 rpm. In the microstructure of the cross section of rice snacks, air cells in rice snacks were not well formed, and cell walls were thicker with increasing feed moisture content and decreasing screw speed.

• Korean Journal of Food Science and Technology
• /
• v.22 no.4
• /
• pp.451-455
• /
• 1990

The extrusion characteristics of pork rind mixed with corn flour were investigated. The blends of pork rind to corn flour in the ratio of 1 : 2, 1 : 1, 2 : 1 and 3 : 1(w/w) were made and each blend was dried up to 5, 10 and 15% moisture content. The blends were extruded by single screw extruder. The extrusion characteristics of each extrudate were as follow. The highest value of expansion ration was attained by mixing pork rind and corn flour in the ratio of 1 : 1, containing 5% moisture content. As the rind content to the corn flour mixture was increased, the bulk density, water absorption index, breaking stregth and redness, of the extradate increased, but the lightness and yellowness decreased. It was concluded that a high quality snack food could by produced by extrusion-cooking the mixture of pork rind and corn flour.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1082-1082
• /
• 2001

Extrusion is one of the most important processes in polymer industry. The characterization of the polymer melt during processing will improve this process noticeably, One possibility of characterizing the actual processed polymer melt is the inline near infrared (NIR) spectroscopy, With this method several polymer properties can be observed during processing, e.g. composition, moisture ormechanical properties of the melt. For this purpose probes for transmission and reflection measurements have been developed, withstanding the high temperatures and pressures appearing during extrusion process (tested up to 300$^{\circ}C$ and 10 ㎫). For the transmission system an optical bypass was developed to eliminate disturbing spectral influences and hence increase the long term stability, which is the prerequisite for an industrial application. Measurements in transmission and reflection produced comparable results (or blending processes, where the prediction error was less than 1%. An optimum RMSEP of only 0.24% was found for preprocessed polymer blends measured in transmission on a laboratory extruder. A transflection measurement allowed for the first time the recording of relevant NIR-spectra in the screw area of an extruder. The application to a (PE+PP) blending process delivered promising results. This new measurement mode allows the observation of the ongoing processes within the screw area, which is of maximum Interest for reactive extrusion processes. Due to economic reasons the calibration transfer between different extrusion systems is also of high importance. Investigations on simulated and real-world spectra showed that a calibration transfer is possible. A new method alternatively to the well-known direct standardization procedures was developed, which is based on an automatic data pretreatment. This procedure delivers comparable results for the calibration transfer. Overall this paper presents concepts, components and algorithms for the inline near infrared (NIR) spectroscopy for polymer extrusion, which allows the use of it in a real industrial extrusion process.

• Korean Journal of Food Science and Technology
• /
• v.31 no.4
• /
• pp.1011-1016
• /
• 1999

This study was performed to search a physical method having high yield and quality and minimum environmental pollution for extraction of pectin from apple pomace. Based on the physical solubilization of plant cell wall under the condition of high temperature, pressure and shearing stress, apple pomace was treated by a corotating intermeshing type twin-screw extruder with the diameter-to-length ratio of 1/20. The specific mechanical energy of extruder was introduced as system parameter for extrusion process modeling and the shaft speed, feed rate and moisture content as process variables. The yield, average molecular weight and galacturonic acid content of water-soluble polysaccharides obtained by extrusion were, respectively, modeled with the linear functions of the system parameter which was of the form as a linear function of process variables. The specific mechanical energy increased with increase of shaft speed and with decrease of feed rate and moisture content. Out of process variables, moisture content had the greatest effect on specific mechanical energy. The yield increased with increase of specific mechanical energy while the average molecular weight and galacturonic acid content increased with its decrease. In aspects of yield and quality of pectin, the results from this study showed the possibility to replace a traditional acidic method with the extrusion treatment of this study.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.441-444
• /
• 2006

Extrusion molding concrete panel is cured two times, that is the steam curing at atmospheric pressure and a high-pressure steam curing(autoclaving). Steam curing at atmospheric pressure is done before autoclaving and to acquire the proper strength for treat in process. Though this curing is the important factor on the quality of product and the speed in manufacturing process, it was not evaluated properly so far. Because of ignorance about curing, some engineers even think that the dry curing is better than the steam curing. This study is to investigate the properties of specimen according to variation of curing conditions in the coring chamber such as laboratory scale, pilot plant, and commercial plant. As estimating, in case of steam curing at atmospheric pressure to make extrusion molding concrete panel, moisture curing is better than dry curing and the desirable maximum temperature in curing chamber is about $50^{\circ}C$.

• Korean journal of food and cookery science
• /
• v.27 no.6
• /
• pp.745-754
• /
• 2011

To improve the textural properties of gluten free rice flour based products, the physicochemical and pasting properties of extruded non-waxy rice flours using extruder were investigated. The high yielding Tongil type rice variety, Hanarum was used. Hanarum rice flour was prepared by dry milling from soaked and dried rice grain. The operation conditions of twin screw extruder were 250 rpm of screw speed, $160^{\circ}C$ of barrel temperature, and 24, 27, and 30% of moisture content. Hanarum extruded rice flour (HERF) were lower in crude lipid and ash contents, but higher in crude protein than Hanarum rice flour (HRF). The color values of HERF showed significantly different (p<0.05) with different moisture contents. Water binding capacities, apparent amylose contents, and damaged starch of HERF were higher than those of HRF. Moisture contents affected water binding capacities of HERF. Solubility increased with increasing heating temperature and solubilities of HERF differed significantly (p<0.05). X-ray crystallinity was changed after extrusion cooking and that of HERF showed sharp peaks at $2{\theta}=18-20^{\circ}$. The pasting viscosities of HERF kept lower values (~ 10 RVU) constantly.