• Journal of the Korea Concrete Institute
• /
• v.26 no.3
• /
• pp.369-375
• /
• 2014

This study examined the changes of microstructural compositions in cement matrix according to the depth from the surface of a reinforced concrete (RC) column exposed to fire. The RC column was exposed to a standard fire for 180 minutes. After the fire test, core samples passing through the column section were obtained. Using the core samples, the remaining fractions of calcium-silicate-hydrates (C-S-H) and calcium hydroxide in cement matrix at the surface, the depth of 40 mm and 80 mm and the center (175 mm) were examined using thermal gravimetric analysis (TGA) and X-ray diffraction analysis (XRDA). Using nuclear magnetic resonance (NMR) technique, the silicate polymerization of C-S-H in cement matrix was also evaluated. The experimental results indicated that the amount of C-S-H loss at the center of column experiencing the transferred fire temperature of $236^{\circ}C$ has been underestimated as the TGA results showed the highest C-S-H contents are located at the depth of 80 mm, where the transferred fire temperature is $419^{\circ}C$. Moreover, the destruction of silicate connections at the center was observed as similar as that at the depth of 40 mm, where the transferred fire temperature was $618^{\circ}C$. This might be attributed to the temperature changes during cooling time after the fire test was neglected. Due to the relatively low thermal conductivity of concrete, the high temperature, which can affect the change of microstructure in cements, will hold longer at the center of the column than other depth.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.4
• /
• pp.235-243
• /
• 1978

A field experiment was conducted to confirm the effect of phosphorus, calcium silicate and different kinds of organic matter to a red-yellow heavy clay textured paddy soil, developed on alluvial terrace. 1. The yield response of phosphorus was very high in both Tongil (Indica x lap.) and Jinheung (Japonica type) varieties. Twenty percent of yield increase with 56kg $P_2O_5$ per 10a. 2. Yield increase by application of phosphorus was closely resulted from increase of tillers per plant. The increases of tillers per plant as observed at harvesting stage by phosphorus fertilization were 3.6 tillers in Tongil, 1.9 in Jinheung, while ripening ratio adversely was decreased 4% in Tongil and increased 3% in Jinheung. 3. High correlation between P content and yield was found at earformation and heading stages. The content of P in rice plant necessary to produce maximum yield in this soil was 0.8 percent at earformation stage. 4. The effect of silicate was not significant for Tongil but was obvious for Jinheung, and the effect of compost and rice husk was also significant for Jinheung. 5. Addition of silicate and lime to phoshorus treatment decreased the nitrogen content of rice plant, especially in Tongil. Accordingly, significant responses of silcate and lime seems be appeared by increasing the rate of nitrogen application.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.64-69
• /
• 1999

Slags are by-products of the metallurgical industry. The most important slag from the standpoint of the quantity used as building material is iron blastfurnace slag. Slags are either crystalline stable solid used as aggregates or glassy material used as hydraulic binder. Slag cements are low heat of hydration cements. Slags react more slowly with than portland cement but they can be activated chemically. Activatiors can be either alkaline activators such as soda, lime, sodium carbonate, sodium silicate or sulphate activators such as calcium sulphate or phosphogypsum. So, in this study slaked lime was used as an activator that the compressive strength of this modified cement(M1 type) is high range in early age. And initial setting time of M1 type cement was shorter than conventional cements.

• Journal of the Korea Safety Management & Science
• /
• v.21 no.4
• /
• pp.45-49
• /
• 2019

The basalt fiber is expected to become a trend for industrial fibers as they have better properties of heat-resistant, non-combustion, absorbent, soundproof, moistureproof, lightweight, corrosion resistant, and high strength properties. Also, the fiber is found to be non-toxic and harmless to the human body. Therefore, in this study, we analyzed the chemical and mineral compositions of powdered sludge of basalt produced at seven sites on Jeju Island for the development of fire resistance insulating material for a building. The results showed that the basalt stone sludge is made from only sodium calcium aluminum silicate and ferridioside components unlike the basalt rock.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.11
• /
• pp.3260-3268
• /
• 2009

A test apparatus has been fabricated to simulate chemical effect on head loss through a strainer in a pressurized water reactor (PWR) containment water pool after a loss of coolant accident (LOCA). Tests were conducted under condition of same ratio of strainer surface area to water volume between the test appratus and the containment sump. A series of tests have been performed to investigate the effects of spray, existence of calcium-silicate with tri-sodium phosphate (TSP), and composition of materials. The results showed that head loss across the chemical bed with even a small amount of calcium-silicate insulation instantaneously increased as soon as TSP was added to the test solution. Also, the head loss across the test screen is strongly affected by spray duration and is increased rapidly at the early stage, because of high dissolution and precipitation of aluminum and zinc. After passivation of aluminum and zinc by corrosion, the head loss increase is much slowed down and is mainly induced by materials such as calcium, silicon, and magnesium leached from NUKONTM and concrete. Furthermore, it is newly found that the spay buffer agent, tri-sodium phosphate, to form protective coating on the aluminum surface and reduce aluminum leaching is not effective for a large amount of aluminum and a long spray.

• Resources Recycling
• /
• v.31 no.6
• /
• pp.52-59
• /
• 2022

Calcium silicate based cement (CSC) is a low-carbon cement that emits less CO₂ by up to 70% compared to ordinary Portland cement during its manufacture. Most developed countries have commercialized CSC, whereas Korea is still investigating the manufacturing characteristics and basic properties of CSC. This paper provides a review of methods for manufacturing CSC using domestic raw materials and discusses the possibility of CSC localization based on an evaluation of the basic physical properties of manufactured CSC. The experimental results of this study indicate that the primary mineral components of CSC were CS, C₃S₂ C₂S, and unreacted SiO₂. This suggests the possibility of manufacturing CSC using domestic raw materials that exhibit mineral compositions similar to that of theoretical CSC. The compressive strength of CSC mortar is less than 1MPa at the age of 7 d under wet curing. This implies that hydration does not affect the property development of CSC mortar. Meanwhile, during carbonation curing, the compressive strength is 56 MPa or higher after 7 d, which indicates excellent early strength development. Furthermore, results of Thermogravimetric Analysis Differential scanning calorimetry (TG/DSC) show that a significant amount of CaCO₃ is formed, which is consistent with the results of previous studies. This implies that carbonation is associated significantly with the properties of CSC.

• Advances in concrete construction
• /
• v.7 no.4
• /
• pp.263-275
• /
• 2019

In the present work, Granulated Blast Furnace Slag (GBFS) and Fly ash (FA) were used as partial replacement of Natural Sand (NS) and Ordinary Portland Cement (OPC) by weight. One control mix, one with GBFS, three with FA and three with GBFS-FA combined mixes were prepared. Replacements were 50% GBFS with NS and 20%, 30% and 40% FA with OPC. Preliminary investigation on development of compressive strength was carried out at 7, 28 and 90 days to ensure sustainability of waste materials in concrete matrix at room temperature. After 90days, thermo-mechanical study was performed on the specimen for a temperature regime of $200^{\circ}-1000^{\circ}C$ followed by furnace cooling. Weight loss, visual inspection along with colour change, residual compressive strength and microstructure analysis were performed to investigate the effect of replacement of GBFS and FA. Although adding waste mineral by-products enhanced the weight loss, their pozzolanicity and formation history at high temperature played a significant role in retaining higher residual compressive strength even up to $800^{\circ}C$. On detail microstructural study, it has been found that addition of FA and GBFS in concrete mix improved the density of concrete by development of extra calcium silicate gel before fire and restricts the development of micro-cracks at high temperature as well. In general, the authors are in favour of combined replacement mix in view of high volume mineral by-products utilization as fire protection.

• Korean Journal of Materials Research
• /
• v.29 no.11
• /
• pp.690-696
• /
• 2019

Geopolymer is an alumina silicate-based ceramic material that has good heat-resistance and fire-resistance; it can be cured at room temperature, and thus its manufacturing process is simple. Geopolymer can be used as a reinforcement or floor finish for high-speed curing applications. In this manuscript, we investigate a high-speed curing geopolymer achieved by adding calcium to augment the curing rate. Metakaolin is used as the main raw material, and aqueous solutions of KOH and $K_2SiO_3$ are used as the activators. As a result of optimizing the high bending strength as a target factor for geopolymers with $SiO_2/Al_2O_3$ ratio of 4.1 ~ 4.8, the optimum ranges of the active agent are found to be $0.1{\leq}K_2O/SiO_2{\leq}0.4$ and $10{\leq}H_2O/K_2O{\leq}32.5$, and the optimum range of the curing accelerator is found to be $$0.82{\leq_-}Ca(OH)_2/Al_2O_3{\leq_-}2.87$$. The maximum flexural strength is found to be 1.35 MPa at $Ca(OH)_2/Al_2O_3=2.82$, $K_2O/SiO_2=0.3$, and $H_2O/K_2O=11.3$. The physical and thermal properties are analyzed to validate the applicability of these materials as industrial insulating parts or repairing finishing materials in construction.

• Korean Journal of Organic Agriculture
• /
• v.6 no.1
• /
• pp.117-125
• /
• 1997

For the environmental protection, it is more desirable to use compost rather than chemical fertilizer. So in this paper, the effects of compost upon the rice quality were investigated with Hwajin Rice as the test variety. The rice quality and physicochemical characteristics were examined and the resrlts are as follows. As to the rice quality, the rate of polished rice was high in the non-fertilizer and the compost plot, the degree of transparency was high in the order of the traditional, the compost+urea, the compost and the non-fertilizer plot. The amylose content (one of the physicochemical characteristies of the rice), the rate of Mg/K, and the adhesivity and the cohesion power (charateristies of texturogram which show the density of boiled rice) were also high in the compost polt. Among the amylogram characteristics, the gelatinization temperature was lowest in the compost plot ; the lowest and the highest degree of viscosity and the break down were also inclined to be higher in the compost plot than in the traditional plot. After the soil test, the components of available phosphorus, organic matters, calcium, magnesium, potassinm and silicate increased in the soil as compared with those before test.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.5
• /
• pp.403-412
• /
• 2018

Recently, needs for utilization of recycled aggregate have been increasing. However, its utilization has been limited due to its high alkalinity, which mostly came from the unremoved cement paste particles that were attached at the surface of recycled aggregate. Various efforts has been made to reduce its alkalinity by using $CO_2$, but currently available methods that uses $CO_2$ generate the problem with pH recovery. Considering the fact that supercritical $CO_2$ ($scCO_2$) can provide more rapid carbonation of cement paste than by normal $CO_2$, $scCO_2$ was utilized in this work. The reaction between $scCO_2$ and hydrated cement paste has been systematically evaluated. According to the results, it was found that powder type showed higher carbonation compared to that of cube specimens. It seems the carbonation by $scCO_2$ has occurred only at the surface of the specimen, and therefore still showed some amount of $Ca(OH)_2$ calcium aluminates after reaction with $scCO_2$. With powder type specimen, all $Ca(OH)_2$ was converted into $CaCO_3$. Moreover, additional calcium that came from both calcium aluminate hydrates and calcium silicate hydrates reacted with $scCO_2$ to form $CaCO_3$. After carbonation with $scCO_2$, the powder type specimen did not show pH recovery, but cube specimens did show due to the presence of portlandite.