• Korean Journal of Materials Research
• /
• v.23 no.10
• /
• pp.568-573
• /
• 2013

The deformation properties of a TiC-Mo eutectic composite were investigated in a compression test at temperatures ranging from room temperature to 2053 K and at strain rates ranging from $3.9{\times}10^{-5}s^{-1}$ to $4.9{\times}10^{-3}s^{-1}$. It was found that this material shows excellent high-temperature strength as well as appreciable room-temperature toughness, suggesting that the material is a good candidate for high-temperature application as a structure material. At a low-temperature, high strength is observed. The deformation behavior is different among the three temperature ranges tested here, i.e., low, intermediate and high. At an intermediate temperature, no yield drop occurs, and from the beginning the work hardening level is high. At a high temperature, a yield drop occurs again, after which deformation proceeds with nearly constant stress. The temperature- and yield-stress-dependence of the strain is the strongest in this case among the three temperature ranges. The observed high-temperature deformation behavior suggests that the excellent high-temperature strength is due to the constraining of the deformation in the Mo phase by the thin TiC components, which is considerably stronger than bulk TiC. It is also concluded that the appreciable room-temperature toughness is ascribed to the frequent branching of crack paths as well as to the plastic deformation of the Mo phase.

• Proceedings of the KIEE Conference
• /
• 2005.11c
• /
• pp.103-106
• /
• 2005

A lot of R&D on the diagnosis of stator winding insolation for large rotating machines has been carried out since the 1970s. The on-line partial discharge measurement has proved to be an effective technique in the evaluation of the state of stator insulation in high voltage rotating machines. The purpose of this paper is to describe the method of the on-line partial discharge measurement on stator windings for hydro- generator with ceramic sensor and measuring system. We developed ceramic coupling sensor, partial discharge measuring system, terminal box and index parameters.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.1
• /
• pp.34-41
• /
• 1998

In this paper, I designed a P1394 serial bus chip as new bus interface architecture which can transmit the multimedia data at the rate of 400 Mbps and guarantee necessary bandwidth. because multimedia data become meaningless data after appropriate time, it is necessary to transfer multimedia data in real time, P1394 serial bus chip designed in this paper support isochronous transfer mode to solve this problem. Also, designed P1394 serial bus chip can transfer high quality video data or high quality audio data because it support the speed of 400 Mbps. While user must set device ID manually in previous interface such as SCSI, device ID is automatically determined if user connect each node with designed P1394 serial bus cable and power on. To design this chip, I verified the behavioral of the entrire system and synthesized layout. Also, I did layout the analog blocks and blocks which must be optimized in full custom.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.22 no.4
• /
• pp.373-382
• /
• 2000

Individual genetic susceptibilities to cancers may result from several factors including differences in xenobiotics metabolism to chemical carcinogens, DNA repair, altered oncogenes and suppressor genes, and environmental carcinogen exposures. Among them, genetic polymorphisms of metabolizing enzymes to chemical carcinogens have been recognized as a major important host factors in human cancers. They have two main types of enzymes: the phase I cytochrome P-450 mediating enzymes (CYPs) and phase II conjugating enzymes. The purpose of this study is to determine the frequencies of genotypes of phase I (CYP1A1 and CYP2E1) and phase II (NAT2) metabolizing enzymes in healthy control and head and neck cancer patients of Korean and to identify the relative high risk genotypes of these metabolizing enzymes to head and neck cancer in Korean. The author has analyzed 132 head and neck cancer patients and 113 healthy controls using polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP). The results were as following; 1. The frequencies of genotypes of CYP1A1, CYP2E1 and NAT2 in healthy control were as following; CYP1A1 exon 7 polymorphism; Ile/Ile: Ile/Val: Val/Val = 59.3%: 36.3%: 4.4% CYP2E1 Pst I polymorphism, C1/C1: C1/C2: C2/C2 = 61.1%: 32.1%: 6.2% NAT2 polymorphism; F/F: F/S: S/S = 43.4%: 48.7%: 8.0% 2. In analysis of phase I enzyme, Val/Val genotype in CYP1A1 exon 7 polymorphism and C2/C2 genotype in CYP2E1 Pst I polymorphism were associated with relative high risks to head and neck cancers (Odds' ratio: 2.09 and 1.37, respectively). 3. Among the genotypes of NAT2 enzyme polymorphism, S/S genotype of NAT2 enzyme had 1.03 times of relative risk to head and neck cancers. 4. In combined genotyping of CYP1A1, CYP2E1, and NAT2 enzymes polymorphisms, the patients with Val/Val and C1/C1, C2/C2 and fast acetylator, and Val/Val and fast acetylator had higher relative risks than the patients with each baseline of combined genotypes (Odds' ratio: 2.82, 1.98 and 2.1, respectively). These results suggest the combined genotypes of Val/Val and C1/C1, C2/C2 and fast acetylator, and Val/Val and fast acetylator were more susceptible to head and neck cancers in Korean. And genotyping of metabolizing enzymes could be useful for predicting individual susceptibility to head and neck cancer.

• Progress in Superconductivity and Cryogenics
• /
• v.17 no.2
• /
• pp.41-44
• /
• 2015

Critical current of high-temperature superconducting (HTS) coil is influenced by its own self magnetic field. Direction and density distribution of the magnetic field around the coil are fixed after the shape of the coil is decided. If the entire part of the HTS tape has homogeneous $I_c$ distribution characteristic, quench would be initiated in fixed location on the coil. However, the actual HTS tape has inhomogeneous $I_c$ distribution along the length. If the $I_c$ distribution of the HTS tape is known, we can expect the spot within the HTS coil that has the highest probability to initiate the quench. In this paper, $I_c$ distribution within the HTS coil under self-field effect is simulated by MATLAB. In the simulation procedure, $I_c$ distribution of the entire part of the HTS tape is assume d to follow Gaussian-distribution by central limit theorem. The HTS coil model is divided into several segments, and the critical current of each segment is calculated based on the-generalized Kim model. Single pancake model is simulated and self-field of HTS coil is calculated by Biot-Savart's law. As a result of simulation, quench-initiating spot in the actual HTS coil can be predicted statistically. And that statistical analysis can help detect or protect the quench of the HTS coil.

• Journal of Welding and Joining
• /
• v.16 no.4
• /
• pp.39-46
• /
• 1998

$CO_2$ gas shielded arc welding has been characterized with its harsh arc compared to Ar-based shielding gases and with its high level of spattere specially in welding current range of 250~300 amperes. In this range of welding current, the metal transfer mode showed to be changed from short circuit to globular with the increase of welding voltage resulting in so-called the transitional mode in which both modes of transfer appeared together. To characterize the transitional mode, the short circuit events were divided into two groups, i.e. normal short circuit (N.S.C) which has short circuit time $(t_s)$ over 2msec and instantaneous short circuit (I.S.C) of $t_s$$\leq$2msec. The experimental results showed that the number of N.S.C decreased almost linearly with the increase of welding voltage and appeared to be not related with spatter generation rate. However I.S.C became to be pronounced in the transitional condition and its number reached the maximum value at around 29.0 volts. Considering the relation with the spatter generation rate, it was found that the number of I.S.C had a very strong correlation with the spatter generation rate of the transitional condition. It was further demonstrated that spatter generation rate decreased quite linearly with the decrease of I.S.C frequency. It implies that I.S.C is the most important waveform factor controlling the spatter generation of the transitional mode, i.e. in the middle range of welding current. Based on these results, It was discussed that in the transitional mode the basic concept of waveform control for suppressing spatter generation would be different from the one applied for typical short circuit transfer mode of low welding current.

• Textile Coloration and Finishing
• /
• v.6 no.2
• /
• pp.30-39
• /
• 1994

To study the printing behaviors of Polyester and cotton(P/C) fabrics printed with disperse and reactive dyes, the effects of alkalis on the fixation of reactive dyes and the alkali-stability of disperse dyes in various methods of fixation were examined. The anthraquinone disperse dyes which have diamino derivatives as substituents without hydroxy group, such as C.I. Disperse Violet 1(D.V.1), C.I. Disperse Violet 28(D.V.28) and C.I.Disperse Blue 60(D.B.60) showed good results of fixation without regard to the concentration of NaHCO$_3$. In case of high temperature steaming(HTS) and unsaturated steaming(US)/HTS, D.V. 1 was alkali-stable and effective for P/C printing. A good result was obtained with D.V.1 and C.I.Reactive Orange 13(R.O.13) paste of 4% $K_{2}CO_{3}$. It was found that the unfixed D.V.28 bearing chloro group can hinder the fixation of monochlorotriaxinyl reactive dyes, and D.B.60 made little stain on 100% cotton. In thermosol(Tm), the dye uptake of D.V.1 was not decreased so much, but those of D.V.28 and D.B.60 were greatly decreased.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.130-133
• /
• 2001

A multifilamentary Bi-2223 HTS tape for superconducting power applications was studied through the fabrication of 250-meter long tapes by the PIT(powder in tube) process. To fabricate continuous long wire, a drawing machine, a two-drum bull block and a rolled tape winding machine were developed. Especially, 250-meter long tapes were heat treated in the shape of pancake coil to reduce the heat affect zone and to achieve the high critical current. Engineering critical current density was improved through both the enhancements of critical current density by control of thermal process and the increase of filling factor by using thin Ag alloy sheath tubes less than 1.5 mm in thickness. We have made successfully 250-meter long 37 filamentary tapes with high filling factor up to 31 % employing the modified drawing and rolling technique. The critical current of 250-meter long tapes with pancake coil type was measured by transport method at self-field up to 250 gauss of center field. The measured values, based on the transport critical current at self-field, $I_{c}$ -B characteristics and magnetic field analysis, are 34 A of I$_{c}$ and 4.0 $kA/\textrm{cm}^2$ of $J_{e}$ at 250 m, 77 K, and 0 T. We also have achieved the 56 A of I$_{c}$ and 7.0 $0 kA/\textrm{cm}^2$ of$ J_{e}$ in short tapes at 77K, self-field, and 1$mutextrm{V}$/cm.

• Progress in Superconductivity and Cryogenics
• /
• v.17 no.1
• /
• pp.6-9
• /
• 2015

For many applications of $ReBa_2Cu_3O_{7-x}$ (ReBCO) tapes it is needed to know the anisotropic properties of the used conductor in a broad range of magnetic field. In this paper we present the results of transport measurements on the SuNAM tape (GdBaCuO) with the rotation of the sample in magnetic fields up to 5 T in liquid nitrogen. The critical current over the magnetic field orientation ($I_c({\theta})$) curves demonstrate the appearance of distinct second peak around c-axis in low fields. This peak almost vanishes in the fields over 3 T. The evolution of the ab-peak form is also presented: the peak consistently reduces its height with the magnetic field going up and in the high fields the shoulders rise, changing the type of the distribution. To describe experimental curves the vortex path model was applied to the angular distributions of the critical current in magnetic field. Good agreements of the experimental data with the analytical expressions were obtained that confirm the vortex path model approach.

• Korean Journal of Poultry Science
• /
• v.22 no.3
• /
• pp.133-144
• /
• 1995

One metabolism trial(Experiment I) and another respiration trial(Experiment II) were conducted to investigate the effects of dietary fiber supplementation(20% wheat bran) on the water balance, blood acid-base balance, body temperature, and metabolic rate of heat-stressed adult roosters. In Experiment I, twenty 20-wk-old SCWL roosters(BW 1.6 kg) were randomly alloted to 4 treatments with 5 birds per treatment and one per replicate. The 4 treatments were consisted of two temperature(21~22˚C vs. 34~35˚C) and two dietary fiber treatment(0% and 20% wheat bran), making Experiment I a 2x2 factorial. After 4 d of preliminary period, birds we subjected to 3-d collection period. Sixteen 20-wk-old SCWL roosters(BW 1.6 kg) were employed Experiment H, with two temperature(21~22˚C vs. 34~35˚C) and two wheat bran levels(0% and 20%). Brids were housed in individual metabolism cages under normal temperature(21~22˚C), at fed one of the experimental diet. After 4 d of preliminary period, a respiration trial with open-circuit gravimetric respiratory apparatus was carried out for each bird for 6 h, one by one, normal(20~21˚C) and hot(34~35˚C) temperatures. The ANOVA test and comparisons among treatment means were done at 5% probability level for both experiments. Results obtained from Experiment I and, II were summarized as follows, 1.The amounts of DM intake and excretion were significantly(P<.05) decreased by heat stress. The DM intake was not affected by the addition of 20% wheat bran, however, the amount of DM excretion was significantly increased by the high fiber diet. Thus, the DM metabolizability decreased significantly by the addition of 20% wheat bran. 2. The heat-stressed roosters increased the water intake and excreta moisture content significantly. Although not significant, the water intake tended to increase in roosters fed the 20% wheat bran diet. 3. The amounts of total water input and evaporative water loss were increased significantly by heat stress, and the addition of 20% wheat bran did not exert any influence on the total water input and evaporative water loss. However, roosters fed the 20% wheat bran diet increased the excreta water output significantly. 4. Neither the heat stress nor the dietary fiber did affect the blood pH, pCO2, and HCO$_3$- significantly. 5. The body temperature increased significantly by the heat stress. However, the high fiber deit failed to decrease the body temperature. 6. The heat-stressed roosters decreased the 02 consumption and C0$_2$ production, and increased the evaporative water loss significantly. However, the high fiber diet did not exert any infulence in this regard. It appears that the beneficial effect, if any, of high fibrous diet during heat stress episode may be due to the increased heat loss through the enhanced excreta water.