• Journal of the Korean Society of Tobacco Science
• /
• v.4 no.2
• /
• pp.23-30
• /
• 1982

Six flue- cured cultivars of Nicotiana tabacum L., 15 possible $F_1$ hybrids and $F_2$ Populations among them, and 15 haploid Populations from Fl hybrids and haploids from Parents, were evaluated. Comparisons of the $F_1$, hybrids and $F_2$ Populations with the Parents indicated that heterosis values were small but significant for yield, plant height, days to flower, leaf length and width and total alkaloids from-6.0% to 5.4% in $F_1$ hybrids, and from -3.4% to 3.6% for Plant height days to flower leaves per plant in $F_2$ populations, respectively. There were positive correlations for yield, plant height, days to flower, leaves per plant and total alkaloids between diploid and haploid populations. Increase or decrease ratio of haploids to diploids of total alkaloids was appeared to 30.3%. Those for yield, leaf length and width, value arid reducing sugar were ranged from -4.1% to -27.6%.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.1
• /
• pp.51-58
• /
• 2015

The counter weight filling is a technology to accumulate soils on the side of berm with a proper width and height for improving the stability of the embankment. This study aims to assess a feasibility of the counter weight filling in the construction of pavement roads for recovery of shear failure during the construction. An effective counter weight filling section was suggested using the numerical analysis. The results showed that the effective counter weight filling section is two-fold (x2) higher than the ratio of width in counter weight filling : embankment height and one third (1/3) to the ratio of height in counter weight filling : embankment height. Also a range of effective trench crossing the counter weight filling required when a trench crossing counter weight filling is installed was suggested by supplying a proper distance between the counter weight filling section and cross-sectional trench.

• The korean journal of orthodontics
• /
• v.20 no.2
• /
• pp.293-304
• /
• 1990

The purpose of this study was to describe the morphologic differences between long-face adults and normal-face adults on the lateral and P-A cephalograms. Long-face and normal-face subifects were selected clinically, and then each of them was taken the lateral cephalogram. According to SN-MP angle and ATFH on the lateral cephalogram, long-face group and normal-face group were classified. 2 long-face adults and 18 normal-face adults were collected, and each of them was taken the P-A cephalogram. The results were as follows: 1. The morphologic differences between long-face adults and normal-face adults were closely related to mandibular morphology. 2. Long-face adults, compared with normal-face adults, demonstrated significant increase in ALFH, and significant decrease in ramus height. 3. Long-face adults, compared with normal-face adults, demonstrated significant increase in AUDH and, ALDH, especially in ALDH. 4. On the P-A cephalogram, no measures of transverse dimension demonstrated significant differences between two groups. 5. On the P-A cephalogram, facial height/facial width ratio was significantly larger than normal in the long-face adults, and in the normal-face adults, facial height/facial width ratio was approximately 90%. 6. In the correlation analysis of SN-MP angle and ATFH with all the other variables, the correlation coefficients of SN-MP angle and PTFH/ATFH that of ATFH and ALFH on the lateral cephalogram demonstrated the highest value, and on the P-A cephalogram, SN-MP angle and Cg-GA-Me (Lt.), ATFH and lower facial height demonstrated the highest value of correlation coefficients.

• Journal of the Ergonomics Society of Korea
• /
• v.36 no.4
• /
• pp.305-323
• /
• 2017

Objective: The purpose of this study was to determine breast shape and ratio of breast enlargement women prior to development of breast enlargement patient's bra. Background: Although there are many previous studies on women's breast that did not undergo breast augmentation surgery, no studies have examined the breast type and proportion of women with breast augmentation. Method: In this study, we analyzed ratios and angles with photographs taken before and after breast augmentation on the frontal and lateral views of the breast, UPF and projection were analyzed too. We also compared the pre-operative and post-operative rates with those of previous breast studies, as well as the post-operative breast types for the desirable breast types. Results: The length and width of the breast base and the height of the breast projection increased after the operation. The rate of increase in width is larger than the vertical distance in the breast base, and the rate of increase in height of the projection is larger than the increase in the width. Specifically, in the vertical distance, the rate of increase in the lower portion is larger than that in the upper portion. In the width, the rate of increase on the inside is larger than that on the outside. Conclusion: The angles of the static relationship with the projection increased and the angles of the minor relation decreased. The changes in the size of the breast were visually observed in the overlapping of the triangle shape before and after the surgery. The changes were composed of the line connecting the angle and the measurement points. The pre-operative upper pole fullness (UPF) was mostly 0 and - 1, but after the surgery, +1, 0, -1, +2 were distributed, while post-operative levels of projection were distributed in the order of level 3> level 1> level 2. In comparison with the desirable breast type, it was found that the anatomical type was a more natural breast type than the round type of implant. Application: These results can be useful as basic data for the breast analysis of breast enlargement patients and their bra patterns.

• Wind and Structures
• /
• v.26 no.5
• /
• pp.317-329
• /
• 2018

Wake characteristics of the flow over a finite square prism at different incidence angles were experimentally investigated using an open-loop wind tunnel. A finite square prism with a width D = 15 mm and a height H = 7D was vertically mounted on a horizontal flat plate. The Reynolds number was varied from $6.5{\times}10^3$ to $28.5{\times}10^3$ and the incidence angle ${\alpha}$ was changed from $0^{\circ}$ to $45^{\circ}$. The ratio of boundary layer thickness to the prism height was about ${\delta}/H=7%$. The time-averaged velocity, turbulence intensity and the vortex shedding frequency were obtained through a single-component hotwire probe. Power spectrum of the streamwise velocity fluctuations revealed that the tip and base vortices shed at the same frequency as that ofspanwise vortices. Furthermore, the results showed that the critical incidence angle corresponding to the maximum Strouhal number and minimum wake width occurs at ${\alpha}_{cr}=15^{\circ}$ which is equal to that reported for an infinite prism. There is a reduction in the size of the wake region along the height of the prism when moving away from the ground plane towards the free end.

• Journal of the Korean Institute of Navigation
• /
• v.11 no.2
• /
• pp.73-88
• /
• 1987

It is well known that the height of tank metacenter above the centroid of fluid in a tank is given by i/v where I is the inertia moment of free surface and v is the fluid volume. It is supposed in this formula that the inclination of ship is small and that the free surface of fluid do not touch the top and the bottom of tank. It the inclination of ship is large, the height of tank metacenter may be possibly greater than that given by i/v. The height of tank metacenter is smaller than i/v when the free surface of fluid touch the top or the bottom of tank. The reasonable method to calculate the height of tank metacenter is presented in this paper and prepared in FORTRAN program by FUNCTION EFFRES. The approximate formula was also developed and given by $g_m=(1+\frac{2}{1}tan^2\theta)[1-EXP\{-12(\frac{\alpha(1-\alpha)k}{tan\theta})^{1.25}\}]\frac{i}{v}$ where $g_m$ is the distance from the centroid of fluid to the tank metacenter, $\theta$ is inclined angle of ship, $\alpha$ is the ratio of filled volume to tank capacity and k is the ratio of the depth to the width of tank. The values calculated by the approximate formula given in this paper were compared with the exact values from the computer program and proved out to be sufficiently precise for practical use.

• Journal of Korea Multimedia Society
• /
• v.19 no.2
• /
• pp.264-270
• /
• 2016

In this paper, we proposed a method which can detect pedestrians from CCTV video and estimate the height of the detected objects. We separate the foreground using Gaussian mixture model and the pedestrian is detected using the conditions such as the width-height ratio and the size of the candidate objects. In order to obtain the optimal model for estimating the height of pedestrian, we get many training data from the pedestrian whose height is known. Using these training data, we designed optimal Wiener height estimator and used to estimate the height of pedestrians. The height of the pedestrian at various distance is estimated and the accuracy is evaluated. In the experimental results, proposed method shows that it can estimate the height of pedestrian for various positions effectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.431-434
• /
• 2009

Conceptual study of an open-circuit type low-speed wind tunnel for test of wind turbine blade is conducted. The tunnel is constituted of a settling chamber, a contraction, closed and open test sections, a diffuser, two corners, a cross leg and a fan and motor. For the performance test, the closed test section width of 1.8 m, height of 1.8 m and length of 5.25 m is selected. The open test section with dimension width of 1.8 m, height of 1.8 m and length of 4.14 m is adopted for aeroacoustic test. The contraction ratio is 9 to 1 and maximum speed in the closed test section is 67 m/sec. Input power in the tunnel is about 238 kW and its energy ratio is 3.6. The wind tunnel designed in present study will be an effective tool in research and development of wind turbine.

• Wind and Structures
• /
• v.29 no.2
• /
• pp.111-127
• /
• 2019

The tapered and set-back type of unconventional designs have been used earlier in many buildings. These shapes are aerodynamically efficient and offer a significant amount of damping against wind-induced forces and excitations. Various studies have been conducted on these shapes earlier. The present study adopts a hybrid approach of turbulence modelling i.e., Detached-eddy Simulation (DES) to investigate the effect of height modified tapered and set-back buildings on aerodynamic forces and their sensitivity towards pressure. The modifications in the flow field around the building models are also investigated and discussed. Three tapering ratios (T.R.=(Bottom width- Top width)/Height) i.e., 5%, 10%, 15% are considered for tapered and set-back buildings. The results show that, mean and RMS along-wind and across-wind forces are reduced significantly for the aerodynamically modified buildings. The extent of reduction in the forces increases as the taper ratio is increased, however, the set-back modifications are more worthwhile than tapered showing greater reduction in the forces. The pressure distribution on the surfaces of the buildings are analyzed and in the last section, the influence of the flow field on the forces is discussed.

• Journal of the Korean Home Economics Association
• /
• v.32 no.2
• /
• pp.219-230
• /
• 1994

The purpose of this comparative research is to investigate the change of the drafting method of the basic patterns for women in Korea. Followings were the findings of this research: 1) The concept of the basic pattern could be found after the first of the 1950s and there was introduction of the many basic patterns. At first measurement couldn't be found. Gradually the personal body type could be expressed in the basic pattern through the practical measurements such as the width of highest bust level and the length of neck to bust. 2) Through the ages the changes of the basic patterns were between 1950,60s and 1980,90s distinctively at the back width back shoulder angle front and back shoulder height from biceps line back neck ratio(height/width) BP position at the biceps line the amounts of underarm dart underarm dart position from the biceps lines and front ease angle at BP line. 3) 4 Grouping the types of the basic pattern followings are their characters; 1st Munwha or Doreme style 2nd waist dart group 3rd underarm dart and rectangular front ease 4th the usage of many measurements like as front length upper bust girth etc.