• Journal of Welding and Joining
• /
• 제5권1호
• /
• pp.73-80
• /
• 1987

During PWHT, it is well known that residual stress in weld HAZ is one of the reasons for PWHT embitterment. In case of static loading, it was experimentally found that fracture toughness of weld HAZ was dependant upon PWHT conditions. However, the effects of PWHT on fatigue behavior are not clearly verified. Therefore, in this paper, the effects of heating rate PWHT conditions and residual stress simulated in weld HAZ of Cr-Mo steel on fatigue crack propagation behavior were evaluated by fatigue Testing and SEM observation. The obtained results are summarized as follows; 1. Applied stress($10 Kgf/mm^2$) in weld HAZ during PWHT tneded to decrease fatigue strength and to increase fatigue crack growth rate. 2. Applied stress and slow heating rate of 60.deg. C/hr during PWHT contributed to precipitin of impurity elements as well as carbide, which promoted the fatigue crack growth. 3. Fatigue crack growth rate decreased at the heating rate of 220.deg. C/hr in contrast with 600.deg. C/hr and 60.deg. C/hr.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.139-147
• /
• 2005

The lubricant impregnated MC nylon has good frictional properties, but its mechanical strength is inferior to steel for the mechanical elements. For the tribological application Nylon as gears, sliding bearings, cam and etc, the steel shafts are fitted in pre-heated nylon cylinder by a process of interference expansion fit and bonded by induction heating method. The joint shear strength of the two materials was measured by a universal test machine. From the study, the adhesive shear strength between these two materials was affected by the factors of the interference between nylon and steel, the size of nylon cylinder, knurl of steel shaft and inducting heating conditions. The most effective jointing conditions were analyzed and decided for the practical application in the industry.

• 한국재료학회지
• /
• 제25권9호
• /
• pp.450-454
• /
• 2015

A simulation method to estimate microstructure dependent material properties and their influence on performance for a honeycomb structured SiC heating element has been established. Electrical and thermal conductivities of a porous SiC sample were calculated by solving a current continuity equation. Then, the results were used as input parameters for a finite element analysis package to predict temperature distribution when the heating element was subjected to a DC bias. Based on the simulation results, a direction of material development for better heating efficiency was found. In addition, a modified metal electrode scheme to decelerate corrosion kinetics was proposed, by which the durability of the water heating system was greatly improved.

• 한국해양바이오학회지
• /
• 제16권1호
• /
• pp.19-25
• /
• 2024

To verify the color change in dried laver postproduction during the heating process, chromaticity elements were compared via a spectrophotometer across various heating conditions within the visible light spectrum. In general, the moisture reduction rate increased with rising temperature and time. Surface image comparisons revealed an expanded area of light reflection on the heat-treated dried laver sample due to surface roughening from shrinkage. No statistically significant differences in chromaticity values were observed in the measurements of brightness (L^*), redness (a^*), and yellowness (b^*). Reflectance spectrum measurements in the visible light region confirmed high reflectance under red wavelength conditions. In particular, a significant increase in reflectance at 700 nm compared with untreated samples was noted. The correlation between the increase in 700 nm reflectance of dried laver samples and heating conditions ranged from 0.7471 to 0.7793, suggesting its potential use as an indicator for comparing color changes in dried laver based on heating conditions.

• 설비공학논문집
• /
• 제29권1호
• /
• pp.1-6
• /
• 2017

In order to better save energy, many buildings have been constructed with high levels of insulation and airtightness in recent years. Additionally, having high quality indoor air has become more relevant, necessitating a ventilating system. This study is aimed at evaluating the performance of a humidity exchanger through computational fluid dynamics (CFD) analysis of elements for the purpose of providing comfortable indoor air and reduced energy consumption. The simulation was conducted with three different shapes (triangle, rectangular, and curve) of heat exchanger elements, in order to find the most effective element. A follow-up simulation then proved the efficiency of the chosen humidity exchanger, which was selected by analyzing the results of the preceding simulation, comparing study data with measurement data from the Korea Testing Laboratory (KTL). The resulting analysis revealed that the rectangular element showed the lowest level of efficiency in both heating and cooling, while the curved element showed the highest level of efficiency in both heating and cooling.

• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2011년도 춘계학술발표대회 논문집
• /
• pp.127-132
• /
• 2011

The purpose of this study was to search the cases of low carbon green housing complex specially focusing on the design elements of ZEDfactory in UK and find the suggestion for the low carbon green housing complex in Korea. For this purpose, we reviewed the design elements of low carbon green housing, which are created by ZEDfactory. We also analyzed the 4 cases of them focusing on the design elements and synthesized the elements. As a result of this study, we can draw some implications and ways to apply the low carbon green concepts for housing complex such as the thermal heating, cooling and microgeneration solution using available renewable energy.

• 동력기계공학회지
• /
• 제20권6호
• /
• pp.20-26
• /
• 2016

For power electronic devices, the thermal energy density per unit volume has seen a rapid increase in recent years, owing to the miniaturization and dense integration of electronic components, as well as the continuous development in performance and function. This research examined the validity and reliability of a thermal safety model for managing the heating conditions of TRIAC electronic components. Among the electronic components of a PCB, these can be considered as a heat source. Using the model, the heating conditions of TRIAC components were maintained at their design target levels in the process of developing an LMT motor drive board. In addition, the heating characteristics of the entire PCB were analyzed to verify its thermal safety. Finally, the reliability and validity of the thermal safety model for maintaining the heating conditions of the TRIAC electronic elements at adequate levels was verified using a numerical analysis method.

• 한국정보통신학회논문지
• /
• 제7권7호
• /
• pp.1533-1538
• /
• 2003

기존에 적용중인 유전가열 합성수지 접착기술의 경우 진공관 소자를 사용하여 10MHz 대역 이상의 스위칭 주파수를 사용하고, 유전손실이 비교적 높은 PVC 소재에 제한적으로 적용해 왔다. 다른 합성수지 소재에 비해서 유전손실이 낮은 친환경적인 소재에 대해서는 적용이 어려운 기술인 관계로 최근 들어 부각되는 친환경적 소재의 적용 확대로 인하여 기존 유전가열 방식의 접착기술은 한계에 접하고 있다. 본 논문에서는 고주파 유도가열 관련 기술을 응용하여 친환경적인 합성소재의 직접가열의 문제점을 간접가열에 의한 온도제어를 적용하여 고주파 유도가열 접착기를 설계하였다.

• 한국기계가공학회지
• /
• 제2권3호
• /
• pp.84-89
• /
• 2003

The joint method and characteristics of lubricant Impregnated MC nylon and metal are analyzed. Considering the productivity and economics, two materials are Joined with the process of turning, knurling, and induction heating. The Joint strength is determined by adhesion of the melted nylon, the size of knurl, and the interference from the difference of the diameters. The parameters affecting induction heating process are analyzed. The adhesion strength of the melted nylon is measured. Finally the joint strength is analyzed in the environments of low, room, and high temperature. The nylon/metal Joined material is expected to be widely used as the sliding machine elements with good friction and shear strength.

• 한국기계가공학회지
• /
• 제19권1호
• /
• pp.1-10
• /
• 2020

This study deals with the fabrication and thermal characterization of planar heating elements attached to the backside of the reflector used in the electrodeless lamp of a freezer. We tried to solve the problem of the local heat generation of the linear heating element that occurs about 50℃. The homogeneous dispersion and manufacturing excellence of the planar heating element produced were confirmed through SEM and EDS. In addition, the test specimens was prepared according to the change in the ratio of carbon fiber to the basis weight of the planar heating element, and a sample having a basis weight of 50g/㎡ having a content ratio of carbon fiber of 70% was selected. That sample showed low surface resistance of 4.3Ω/sq and high temperature of about 81℃ at 6V. Durability was confirmed by performing repeated bending evaluation of 3000 cycles for the sample. Large area test specimens were prepared to be applied to the actual reflector, insulated by EVA film and analyzed for their thermal characteristics. From 13V application, the temperature of the linear heating element was higher than 50℃ and the average temperature of 68℃ was maximum at 18V.