• 제목/요약/키워드: heat transfer method

검색결과 2,033건 처리시간 0.035초

지하수 관개에 의한 수도의 멸준양상과 그 방지책에 관한 연구 (Studies on the Rice Yield Decreased by Ground Water Irrigation and Its Preventive Methods)

  • 한욱동
    • 한국농공학회지
    • /
    • 제16권1호
    • /
    • pp.3225-3262
    • /
    • 1974
  • The purposes of this thesis are to clarify experimentally the variation of ground water temperature in tube wells during the irrigation period of paddy rice, and the effect of ground water irrigation on the growth, grain yield and yield components of the rice plant, and, furthermore, when and why the plant is most liable to be damaged by ground water, and also to find out the effective ground water irrigation methods. The results obtained in this experiment are as follows; 1. The temperature of ground water in tube wells varies according to the location, year, and the depth of the well. The average temperatures of ground water in a tubewells, 6.3m, 8.0m deep are $14.5^{\circ}C$ and $13.1^{\circ}C$, respercively, during the irrigation period of paddy rice (From the middle of June to the end of September). In the former the temperature rises continuously from $12.3^{\circ}C$ to 16.4$^{\circ}C$ and in the latter from $12.4^{\circ}C$ to $13.8^{\circ}C$ during the same period. These temperatures are approximately the same value as the estimated temperatures. The temperature difference between the ground water and the surface water is approximately $11^{\circ}C$. 2. The results obtained from the analysis of the water quality of the "Seoho" reservoir and that of water from the tube well show that the pH values of the ground water and the surface water are 6.35 and 6.00, respectively, and inorganic components such as N, PO4, Na, Cl, SiO2 and Ca are contained more in the ground water than in the surface water while K, SO4, Fe and Mg are contained less in the ground water. 3. The response of growth, yield and yield components of paddy rice to ground water irrigation are as follows; (l) Using ground water irrigation during the watered rice nursery period(seeding date: 30 April, 1970), the chracteristics of a young rice plant, such as plant height, number of leaves, and number of tillers are inferior to those of young rice plants irrigated with surface water during the same period. (2) In cases where ground water and surface water are supplied separately by the gravity flow method, it is found that ground water irrigation to the rice plant delays the stage at which there is a maximum increase in the number of tillers by 6 days. (3) At the tillering stage of rice plant just after transplanting, the effect of ground water irrigation on the increase in the number of tillers is better, compared with the method of supplying surface water throughout the whole irrigation period. Conversely, the number of tillers is decreased by ground water irrigation at the reproductive stage. Plant height is extremely restrained by ground water irrigation. (4) Heading date is clearly delayed by the ground water irrigation when it is practised during the growth stages or at the reproductive stage only. (5) The heading date of rice plants is slightly delayed by irrigation with the gravity flow method as compared with the standing water method. (6) The response of yield and of yield components of rice to ground water irrigation are as follows: \circled1 When ground water irrigation is practised during the growth stages and the reproductive stage, the culm length of the rice plant is reduced by 11 percent and 8 percent, respectively, when compared with the surface water irrigation used throughout all the growth stages. \circled2 Panicle length is found to be the longest on the test plot in which ground water irrigation is practised at the tillering stage. A similar tendency as that seen in the culm length is observed on other test plots. \circled3 The number of panicles is found to be the least on the plot in which ground water irrigation is practised by the gravity flow method throughout all the growth stages of the rice plant. No significant difference is found between the other plots. \circled4 The number of spikelets per panicle at the various stages of rice growth at which_ surface or ground water is supplied by gravity flow method are as follows; surface water at all growth stages‥‥‥‥‥ 98.5. Ground water at all growth stages‥‥‥‥‥‥62.2 Ground water at the tillering stage‥‥‥‥‥ 82.6. Ground water at the reproductive stage ‥‥‥‥‥ 74.1. \circled5 Ripening percentage is about 70 percent on the test plot in which ground water irrigation is practised during all the growth stages and at the tillering stage only. However, when ground water irrigation is practised, at the reproductive stage, the ripening percentage is reduced to 50 percent. This means that 20 percent reduction in the ripening percentage by using ground water irrigation at the reproductive stage. \circled6 The weight of 1,000 kernels is found to show a similar tendency as in the case of ripening percentage i. e. the ground water irrigation during all the growth stages and at the reproductive stage results in a decreased weight of the 1,000 kernels. \circled7 The yield of brown rice from the various treatments are as follows; Gravity flow; Surface water at all growth stages‥‥‥‥‥‥514kg/10a. Ground water at all growth stages‥‥‥‥‥‥428kg/10a. Ground water at the reproductive stage‥‥‥‥‥‥430kg/10a. Standing water; Surface water at all growh stages‥‥‥‥‥‥556kg/10a. Ground water at all growth stages‥‥‥‥‥‥441kg/10a. Ground water at the reproductive stage‥‥‥‥‥‥450kg/10a. The above figures show that ground water irrigation by the gravity flow and by the standing water method during all the growth stages resulted in an 18 percent and a 21 percent decrease in the yield of brown rice, respectively, when compared with surface water irrigation. Also ground water irrigation by gravity flow and by standing water resulted in respective decreases in yield of 16 percent and 19 percent, compared with the surface irrigation method. 4. Results obtained from the experiments on the improvement of ground water irrigation efficiency to paddy rice are as follows; (1) When the standing water irrigation with surface water is practised, the daily average water temperature in a paddy field is 25.2$^{\circ}C$, but, when the gravity flow method is practised with the same irrigation water, the daily average water temperature is 24.5$^{\circ}C$. This means that the former is 0.7$^{\circ}C$ higher than the latter. On the other hand, when ground water is used, the daily water temperatures in a paddy field are respectively 21.$0^{\circ}C$ and 19.3$^{\circ}C$ by practising standing water and the gravity flow method. It can be seen that the former is approximately 1.$0^{\circ}C$ higher than the latter. (2) When the non-water-logged cultivation is practised, the yield of brown rice is 516.3kg/10a, while the yield of brown rice from ground water irrigation plot throughout the whole irrigation period and surface water irrigation plot are 446.3kg/10a and 556.4kg/10a, respectivelely. This means that there is no significant difference in yields between surface water irrigation practice and non-water-logged cultivation, and also means that non-water-logged cultivation results in a 12.6 percent increase in yield compared with the yield from the ground water irrigation plot. (3) The black and white coloring on the inside surface of the water warming ponds has no substantial effect on the temperature of the water. The average daily water temperatures of the various water warming ponds, having different depths, are expressed as Y=aX+b, while the daily average water temperatures at various depths in a water warming pond are expressed as Y=a(b)x (where Y: the daily average water temperature, a,b: constants depending on the type of water warming pond, X; water depth). As the depth of water warning pond is increased, the diurnal difference of the highest and the lowest water temperature is decreased, and also, the time at which the highest water temperature occurs, is delayed. (4) The degree of warming by using a polyethylene tube, 100m in length and 10cm in diameter, is 4~9$^{\circ}C$. Heat exchange rate of a polyethylene tube is 1.5 times higher than that or a water warming channel. The following equation expresses the water warming mechanism of a polyethylene tube where distance from the tube inlet, time in day and several climatic factors are given: {{{{ theta omega (dwt)= { a}_{0 } (1-e- { x} over { PHI v })+ { 2} atop { SUM from { { n}=1} { { a}_{n } } over { SQRT { 1+ {( n omega PHI) }^{2 } } } } LEFT { sin(n omega t+ { b}_{n }+ { tan}^{-1 }n omega PHI )-e- { x} over { PHI v }sin(n omega LEFT ( t- { x} over {v } RIGHT ) + { b}_{n }+ { tan}^{-1 }n omega PHI ) RIGHT } +e- { x} over { PHI v } theta i}}}}{{{{ { theta }_{$\infty$ }(t)= { { alpha theta }_{a }+ { theta }_{ w'} +(S- { B}_{s } ) { U}_{w } } over { beta } , PHI = { { cpDU}_{ omega } } over {4 beta } }}}} where $\theta$$\omega$; discharged water temperature($^{\circ}C$) $\theta$a; air temperature ($^{\circ}C$) $\theta$$\omega$';ponded water temperature($^{\circ}C$) s ; net solar radiation(ly/min) t ; time(tadian) x; tube length(cm) D; diameter(cm) ao,an,bn;constants determined from $\theta$$\omega$(t) varitation. cp; heat capacity of water(cal/$^{\circ}C$ ㎥) U,Ua; overall heat transfer coefficient(cal/$^{\circ}C$ $\textrm{cm}^2$ min-1) $\omega$;1 velocity of water in a polyethylene tube(cm/min) Bs ; heat exchange rate between water and soil(ly/min)

  • PDF

IBC형 태양전지를 위한 균일하게 증착된 비정질 실리콘 층의 광섬유 레이저를 이용한 붕소 도핑 방법 (Boron Doping Method Using Fiber Laser Annealing of Uniformly Deposited Amorphous Silicon Layer for IBC Solar Cells)

  • 김성철;윤기찬;경도현;이영석;권태영;정우원;이준신
    • 한국전기전자재료학회:학술대회논문집
    • /
    • 한국전기전자재료학회 2009년도 하계학술대회 논문집
    • /
    • pp.456-456
    • /
    • 2009
  • Boron doping on an n-type Si wafer is requisite process for IBC (Interdigitated Back Contact) solar cells. Fiber laser annealing is one of boron doping methods. For the boron doping, uniformly coated or deposited film is highly required. Plasma enhanced chemical vapor deposition (PECVD) method provides a uniform dopant film or layer which can facilitate doping. Because amorphous silicon layer absorption range for the wavelength of fiber laser does not match well for the direct annealing. In this study, to enhance thermal affection on the existing p-a-Si:H layer, a ${\mu}c$-Si:H intrinsic layer was deposited on the p-a-Si:H layer additionally by PECVD. To improve heat transfer rate to the amorphous silicon layer, and as heating both sides and protecting boron eliminating from the amorphous silicon layer. For p-a-Si:H layer with the ratio of $SiH_4$ : $B_2H_6$ : $H_2$ = 30 : 30 : 120, at $200^{\circ}C$, 50 W, 0.2 Torr for 30 minutes, and for ${\mu}c$-Si:H intrinsic layer, $SiH_4$ : $H_2$ = 10 : 300, at $200^{\circ}C$, 30 W, 0.5 Torr for 60 minutes, 2 cm $\times$ 2 cm size wafers were used. In consequence of comparing the results of lifetime measurement and sheet resistance relation, the laser condition set of 20 ~ 27 % of power, 150 ~ 160 kHz, 20 ~ 50 mm/s of marking speed, and $10\;{\sim}\;50 {\mu}m$ spacing with continuous wave mode of scanner lens showed the correlation between lifetime and sheet resistance as $100\;{\Omega}/sq$ and $11.8\;{\mu}s$ vs. $17\;{\Omega}/sq$ and $8.2\;{\mu}s$. Comparing to the singly deposited p-a-Si:H layer case, the additional ${\mu}c$-Si:H layer for doping resulted in no trade-offs, but showed slight improvement of both lifetime and sheet resistance, however sheet resistance might be confined by the additional intrinsic layer. This might come from the ineffective crystallization of amorphous silicon layer. For the additional layer case, lifetime and sheet resistance were measured as $84.8\;{\Omega}/sq$ and $11.09\;{\mu}s$ vs. $79.8\;{\Omega}/sq$ and $11.93\;{\mu}s$. The co-existence of $n^+$layeronthesamesurfaceandeliminating the laser damage should be taken into account for an IBC solar cell structure. Heavily doped uniform boron layer by fiber laser brings not only basic and essential conditions for the beginning step of IBC solar cell fabrication processes, but also the controllable doping concentration and depth that can be established according to the deposition conditions of layers.

  • PDF

3-ring 임피던스미터의 유체 전기 전도도 독립성에 대한 실험적 연구 (Experimental Study of Characteristics of Three-Ring Impedance Meter and Dependence of Characteristics on Electric Conductivity of Fluids)

  • 김종록;안예찬;김무환
    • 대한기계학회논문집B
    • /
    • 제34권11호
    • /
    • pp.1027-1033
    • /
    • 2010
  • 2상유동(기체-액체) 현상은 전자기발전, 원자력발전, 철강산업 등 유체 시스템에 자주 나타나는 현상으로, 2상유동을 파악하는 것은 유체 시스템의 안정성 및 성능을 위해 중요하다. 2상유동 특성 중 기공률은 압력강하와 열전달 성능을 결정하는 주요 인자로서 이를 측정하는 기술이 특히 중요하다. 유동의 임피던스를 측정하여 기공률을 산정하는 임피던스법은 전기적 특성을 이용하기 때문에 반응속도가 빨라 실시간 측정이 가능하며, 유동관 벽에 전극을 설치할 경우 유동 교란없이 측정할 수 있는 장점이 있다. Coney는 원형관에 적용할 수 있는 ring 임피던스미터를 이론적 연구하였다. 본 연구에서는 Coney가 이론적으로 제안하고 실험적으로 검증하지 못한 3-ring 임피던스미터의 유체 전기전도도에 대한 독립성을 실험적으로 검증하였다.

동굴처분 방식을 사용하는 방사성 폐기물 처분장의 자연 환기 타당성 평가 (The Feasibility of Natural Ventilation in Radioactive Waste Repository Using Rock Cavern Disposal Method)

  • 김진;권상기
    • 방사성폐기물학회지
    • /
    • 제3권3호
    • /
    • pp.183-192
    • /
    • 2005
  • 자연환기는 처분장의 작업 환경 및 위생, 부유 방사성 핵종의 노출 등과 같은 안전문제에 있어 자연환기 자체만으로는 기계적 강제 환기에 비해서 덜 효과적이지만 처분장 내의 수분제거, 작업 환경 조성과 관련하여 라돈 (Rn) 가스의 희석과 같은 향후 처분장의 장기적 환경을 위해서는 중요한 역할을 할 수 있고, 환풍기와 같은 환기 설비를 이용해야하는 기계환기에 비해 경제적으로 매우 효과적 일수 있다. 본 논문에서는 지하 처분장의 건설 및 운영 기간동안 자연환경 조건에 따라 처분장에 스스로 생기는 자연 환기의 타당성에 대하여 기술하였다. 자연 동굴을 통한 자연환기 유사에 의해 밝혀진 증거들과, 수직갱을 갖는 산악 도로터널에서의 자연 환기 측정, 그리고 주어진 자연환기 압력에 의한 공기 발생량 계산 등을 통해서 자연 환기는 한국형 지하 방사성 폐기물 처분장에 잠재적으로 매우 유익함을 알 수 있다. 효과적으로 유도된 자연 환기는 방사성 폐기물 처분장 내에 발생하는 열과 습도, 그리고 라돈 가스를 제어하기에 경제적으로 좋은 방법이 될 수 있다. 자연환기를 통해 처분장의 전반적 열적 특성은 개선될 수 있고, 수분으로 포화된 공기는 효과적으로 건조되고 그 건조상태 유지 기간은 확장 될 수 있을 것이다.

  • PDF

반도체 폐가스 처리용 열분해반응기의 입구형상이 열유동 특성에 미치는 영향에 관한 수치해석 연구 (Effect of Inlet Shape on Thermal Flow Characteristics for Waste Gas in a Thermal Decomposition Reactor of Scrubber System)

  • 윤종혁;김영배;송형운
    • 공업화학
    • /
    • 제29권5호
    • /
    • pp.510-518
    • /
    • 2018
  • 최근에 반도체 산업의 지속적인 발전에 따라 반도체 생산공정에서 발생하는 다양한 오염가스를 처리하는 기술에 대한 관심도 늘어나고 있다. 이처럼 반도체 공정 후 배출되는 폐가스를 제거하는 장치 중의 하나로서 다양한 종류의 스크러버 시스템이 사용되고 있다. 이러한 스크러버 시스템 내 열분해반응기 성능은 폐가스 내 오염원 제거효율과 전반적인 운전안정성에 영향을 미치기 때문에 열분해 반응기의 효율적인 설계가 매우 중요하다. 본 연구에서는 수치해석 방법을 기반으로 반응기 내 폐가스의 열유동 특성을 파악하고자 하였다. 해석기법을 검증하기 위해 온도분포에 대한 해석결과를 실험결과와 비교하였다. 온도결과에 대한 해석과 실험은 약 1.27~2.25% 수준의 낮은 오차를 보였으며 이를 통해 해석결과의 타당성을 확보하였다. 검증된 해석기법을 이용하여, 기존 반응기의 성능개선을 위한 설계 가이드라인을 제시하기 위해 폐가스 형상 변화에 따른 해석을 수행하여 기존모델 및 수정모델에서 폐가스의 거동특성을 비교분석하였다. 본 연구에서 수행한 결과는 다양한 스크러버 시스템 내 열유동 특성을 분석하는데 기초자료로 활용될 수 있을 것으로 기대한다.

시설하우스 에너지 절감을 위한 열유동 수치 해석 심층 연구 (Indepth Study of Numerical Heat Transfer and Fluid Flow for Energy Saving of Greenhouse)

  • 신미수;김혜숙;최준호;장동순
    • 대한환경공학회지
    • /
    • 제29권4호
    • /
    • pp.466-471
    • /
    • 2007
  • 본 연구의 목적은 시설하우스에 대한 기본적이면서도 중요한 운전 자료를 얻기 위한 것이다. 특히 시설하우스 에너지 절감을 위해 실용적으로 쉽게 적용할 수 있는 방법에 중점을 두었다. 이러한 목적에 의해 하우스내의 온도분포를 평가하기 위한 방법으로 조직적인 수치해석연구를 수행하였다. 이러한 연구에서 고려한 중요한 변수는 시설하우스의 일반적인 형상과 함께 시설하우스내의 열유동을 조절하는 다양한 배플 조건을 가정하였다. 아울러 난방가열시스템의 배관배치에 따른 열유동 특성과 효율을 상호 비교하였다. 이러한 연구의 결과로 얻어진 몇 가지의 유용한 결론을 정리하였다. 특히 시설하우스 천장에서 내린 배플은 최소한의 시설로서 에너지 효율에 실질적인 기여를 할 수 있었으며 또한 난방배관의 구조는 시설하우스내의 균일한 온도 분포을 얻기 위하여 크게 영향을 미치고 있음을 확인하였다. 기타 본연구의 여러 수치해석 결과들은 물리적인 면에서 의미가 있었으며 실용적인 면에서 시설하우스의 최적 운전조건의 설정에 도움이 된다고 판단하였다.

전산유체학을 이용한 고준위 방사성 폐기물 처분장의 자연환기량에 의한 온도예측 (A Study on the Prediction of HLW Temperature from Natural Ventilation Quantity using CFD)

  • 노장훈;유영석;장승현;박선오;김진
    • 터널과지하공간
    • /
    • 제22권6호
    • /
    • pp.429-437
    • /
    • 2012
  • 본 연구에서는 고준위 방사성 폐기물 처분장의 특징인 높은 고도차와 온도차이로 인해 발생하는 자연환기량을 바탕으로 처분터널내 온도를 전산유체학을 활용하여 예측하였다. 선행된 연구에서 Hydrostatic method와 CFD를 활용하여 자연환기량을 정량적으로 평가한 결과 상당히 큰 자연환기량이 발생이 됨을 확인하였다. 이러한 결과를 바탕으로 폐기물 발열량에 따라 발생되는 자연환기량으로 인한 처분터널내 온도예측을 실시하였으며, 처분장을 크게 심지층 처분장과 지상처분장으로 나누어 온도예측을 실시하였다. 해석결과 심지층 처분장은 암반으로의 열전달과 충분한 자연환기량의 발생으로 처분장내 온도 제어에 효과적인 반면에, 지상처분장의 경우 외부온도의 영향을 크게 받고 충분한 자연환기량을 발생시키지 못하여 온도제어에는 불리함을 확인하였다. 또한 심도 200 m 심지층 처분장의 경우 심도 500 m까지 약 $10^{\circ}C$정도의 열이 전달됨을 확인하였다. 즉, 국내에 건설예정인 고준위 방사성 폐기물 처분장을 온도제어에 중점을 두고 설계한다면 지상처분장보다는 심지층 처분장이 타당한 것으로 연구되었다.

전구체의 물성에 따른 리튬 2차전지용 Li(Ni0.5Co0.2Mn0.3)O2의 전기화학적 특성 변화 (Influence of Precursor on the Electrochemical Properties of Li(Ni0.5Co0.2Mn0.3)O2 Cathode for the Lithium Secondary Battery)

  • 강동현;;채정은;김성수
    • 전기화학회지
    • /
    • 제16권4호
    • /
    • pp.191-197
    • /
    • 2013
  • 리튬2차전지용 양극소재인 $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$를 공침법을 이용해 $Ni_{0.5}Co_{0.2}Mn_{0.3}(OH)_2$ 전구체로부터 합성하였고, 공침조건을 조절하여 전구체의 1차 입자 형상을 Flake형상과 Needle형상으로 제어하였다. 동일한 공정으로 리튬과 혼합하고 열처리하여, 입도, 탭밀도, 화학적 성분 등이 동일한 분체물성의 양극 소재를 합성하였다. 전구체의 1차입자 형상에 따른 $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$의 전기화학적 특성을 평가하고, 이 특성의 변화를 SEM, XRD, EELS로 이용하여 분석하여 연관성을 고찰하였다. Needle형상 전구체로 합성한 $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ 양극의 1차입자는 Flake형상 전구체로 합성한 경우보다 작고, EELS결과로는 입자표면의 Li농도가 내부보다 상대적으로 높았다. 전기화학적인 수명과 출력특성에서 Needle형상 전구체로 합성한 양극이 Flake형상 전구체의 경우보다 우수한 특성을 보였는데, 임피던스 측정으로부터 낮은 전하이동저항에 연관되어 있을 것으로 생각된다.

백금 히터가 내장된 평면형 Bi-Sb 다중접합 열전변환기의 특성 (Characteristics of a planar Bi-Sb multijunction thermal converter with Pt-heater)

  • 이현철;김진섭;함성호;이종현;이정희;박세일;권성원
    • 센서학회지
    • /
    • 제7권3호
    • /
    • pp.154-162
    • /
    • 1998
  • 필라멘트 모양의 백금 박막 히터 및 Bi-Sb 박막 열전퇴(thermopile)의 고온 접합부를 열차단막 역할을 하는 $Si_{3}N_{4}/SiO_{2}/Si_{3}N_{4}$ 다이아프램위에, 열전퇴의 저온 접합부를 방열판 역할을 하는 실리콘 기판에 의해 지지되는 유전체 멤버레인위에 각각 형성시켜, 열감도가 높고 교류-직류 변환오차가 작은 평면형 Bi-Sb 다중접합 열전변환기를 제작하고, fast reversed dc 방법으로 변환기의 교류-직류 변환특성을 측정하였다. 단일 bifilar 히터로 제작된 변환기의 열감도는 공기 및 진공중에서 각각 약 10.1 mV/mW 및 14.8 mV/mW였고, 2중 bifilar 히터로 제작된 변환기의 열감도는 안쪽 및 바깥쪽에 있는 히터를 입력으로 하였을 강우 공기 및 진공중에서 각각 약 5.1 mV/mW 및 7.6 mV/mW 그리고 각각 약 5.3 mV/mW 및 7.8 mV/mW로서, 기체에 의한 열손실이 거의 없는 진공중에서의 열감도가 공기중에서의 열감도보다 더 높게 나타났다. 10 kHz이하의 주파수 범위에서 변환기의 교류-직류 전압 및 전류 변환오차 범위는, 단일 bifilar 히터로 제작된 경우 공기중에서 각각 약 ${\pm}1.80\;ppm$${\pm}0.58\;ppm$이었고, 2중 bifilar 히터로 제작된 경우 안쪽 및 바깥쪽 히터를 입력으로 하였을 때 공기중에서 각각 약 ${\pm}0.63\;ppm$${\pm}0.25\;ppm$ 그리고 각각 약 ${\pm}0.53\;ppm$${\pm}0.27\;ppm$였다.

  • PDF

Urease gene의 전이에 의한 길항세균 Bacillus sp. SH14의 길항능력 증가 (Improvement in Antagonistic Ablility of Antagonistic Bacterium Bacillus sp. SH14 by Transfer of the Urease Gene.)

  • 최종규;김상달
    • 한국미생물·생명공학회지
    • /
    • 제26권2호
    • /
    • pp.122-129
    • /
    • 1998
  • 최근 생물방제균으로 주목받고 있는 Enterobacter cloacae의 방제기작이 이 균에 의해 토양내에서 생산된 휘발성 ammonia이며 ammonia의 생산에는urease가 관계한다는 보고를 근거로 하여, 항생물질 생산성 균주로 선발된 우수한 길항균주에 암모니아 생성능, 즉 urease 유전자를 유전적으로 부가함으로써 항진균성 길항물질 생산과 암모니아 생산이 동시에 이루어 질 수 있는 새로운 다기능의 생물방제균을 유전적으로 육종하고자 하였다. 저병해 인삼경작지로부터 식물근부균 Fusarium solani의 생육을 강하게 억제하는 길항세균 한 균주 SH14균주를 분리, 선발하였으며, 분리된 균주를 동정한 결과 Bacillus subtilis이거나 그 근연종으로 추정되었다. 억제기작 실험을 통해 길항균주 B. subtilis SH14에 의해 생산되는 항진균성 길항물질은 외막가수분해효소와 같은 고분자 물질이 아니라 열에 안정한 저분자의 항생물질임을 알 수 있었다. 한편 ammonia 생산을 위한 urease의 유전자는 urease 생산력이 강력한 호알칼리성 Bacillus pasteurii의 urease 생산유전자를 E. coli-Bacillus shuttle vector인 pEB203에 subcloning하였고, 이어서 pGU 366으로 명명된 이 recombinant plasmid를 선발된 항진균성 길항균주 B. subtilis SH14에 PEG-induced protoplast transformation 방법으로 도입, 발현시켰으며, 최적조건을 조사하여 90분간의 lysozyme 처리과정 후 1.5 $\mu\textrm{g}$/$m\ell$의 DNA와 40% PEG4000의 첨가로 약 6.5$\times$$10^{-4}$의 형질전환율을 얻을 수 있었다. 아울러 암모니아 생성능이 부가된 생물방제균 B. subtilis SH14(pGU366)에 의해 식물근부균 F. solani에 대한 생육억제력이 증가되는지 여부를 억제거리 측정법과 균체중량법을 통해 확인한 결과 urease 유전자가 도입된 형질전환체 B. subtilis SH14(pGU366)의 근부균 생육억제능이 각각 36.7%, 44.0%정도로 숙주균주인 B. subtilis SH14에 비해 근부균 생육억제능을 보다 강하게 나타내었음을 알 수 있었다. 따라서 항진균성 항생물질 생산성 생물방제균 B. subtilis SH14에 외부의 urease유전자를 도입하여 ammonia 생성능을 부가함으로써 생물방제력의 상승효과를 거둘 수 있었다.

  • PDF