• 열처리공학회지
• /
• 제26권1호
• /
• pp.1-6
• /
• 2013

The B2-ordered NiAl has attracted much attention as one of the candidates as a next generation high temperature material, because it has a high melting temperature, a low specific gravity and an excellent high temperature oxidation resistance. However, the application of NiAl to structural materials needs the improvement of its brittleness at room temperature. The study was carried out on the relation between several properties of NiAl and some variation of Ni content within NiAl phase, which means deviations from the stoichiometric composition. The main results were as follows; (i) Good ductility was obtained at the testing temperature more than 1073 K irrespective of Ni content. (ii) Increasing Ni content offered preferable tensile properties. (iii) Every NiAl with varying Ni contents showed the superior oxidation resistance.

• 열처리공학회지
• /
• 제4권4호
• /
• pp.53-60
• /
• 1991

This study has been performed to investigate into the internal oxidation characteristics of low carbon steel with respect to the added amount of air in nitrogen-propane atmosphere after gas carburizing for various times at $930^{\circ}C$. The results obtained from the experiment are as follows ; (1) Optical micrographs have shown that the internal oxidation is unlikely to occur in the gas atmosphere without air and that oxidized zone in the outer surface layer is formed in the gas atmosphere with air revealing that the depth of oxidized zone increases with increasing the added amount of air. (2) The formation of internally oxidized zone in the outer surface layer has been found to be inhibited as Ni content increases, i. e, the amount of alloying element increases. (3) The depth of oxidation has been measured to increase with almost parabolically gas carburizing time of up to 6 hours.

• 한국환경과학회지
• /
• 제26권11호
• /
• pp.1201-1208
• /
• 2017

Oxidative degradation of chlorinated ethenes was carried out using heat-activated persulfate. The activation rate of persulfate was dependent on the temperature and the activation reaction rate could be explained based on the Arrhenius equation. The activation energy of persulfate was 19.3 kcal/mol under the assumption that the reaction between the sulfate radical and tricholoroethene (TCE) is very fast. Activation could be achieved at a moderate temperature, so that the adverse effects due to high temperature in the soil environment were mitigated. The reaction rate of TCE was directly proportional to the concentration of persulfate, indicating that the remediation rate can be controlled by the concentration of the injected persulfate. The solution was acidized after the oxidation, and this was dependent on the oxidation temperature. The consumption rate of persulfate was high in the presence of the target organic, but the self-decomposition rate became very low as the target was completely removed.

• 한국세라믹학회지
• /
• 제28권1호
• /
• pp.53-59
• /
• 1991

The reaction product between Si3N4 and ZrO2 has been studied by heat treatment of Si3N4-Zr(Y)O2 composite in high vacuum(<10-5 torr) and in air at $700^{\circ}C$. ZrN was formed after heat treatment in vacuum and easily oxidized after heat treatment in air. The amount of ZrN is related to the Y2O3 content dissolved in ZrO2. After the heat treatment in air the toughness increased and the spalling due to the oxidation of ZrN in specimen surface was observed. As a result, it is suggested that the formation of ZrN phase in Si3N4-ZrO2 composite enhance the toughness of the composite in an oxidation conditon.

• 한국분말재료학회지
• /
• 제24권2호
• /
• pp.133-140
• /
• 2017

This study investigates the oxidation properties of Fe-14Cr ferritic oxide-dispersion-strengthened (ODS) steel at various high temperatures (900, 1000, and $1100^{\circ}C$ for 24 h). The initial microstructure shows that no clear structural change occurs even under high-temperature heat treatment, and the average measured grain size is 0.4 and $1.1{\mu}m$ for the as-fabricated and heat-treated specimens, respectively. Y-Ti-O nanoclusters 10-50 nm in size are observed. High-temperature oxidation results show that the weight increases by 0.27 and $0.29mg/cm^2$ for the as-fabricated and heat-treated ($900^{\circ}C$) specimens, and by 0.47 and $0.50mg/cm^2$ for the as-fabricated and heat-treated ($1000^{\circ}C$) specimens, respectively. Further, after 24 h oxidation tests, the weight increases by 56.50 and $100.60mg/cm^2$ for the as-fabricated and heat-treated ($1100^{\circ}C$) specimens, respectively; the latter increase is approximately 100 times higher than that at $1000^{\circ}C$. Observation of the surface after the oxidation test shows that $Cr_2O_3$ is the main oxide on a specimen tested at $1000^{\circ}C$, whereas $Fe_2O_3$ and $Fe_3O_4$ phases also form on a specimen tested at $1100^{\circ}C$, where the weight increases rapidly. The high-temperature oxidation behavior of Fe-14Cr ODS steel is confirmed to be dominated by changes in the $Cr_2O_3$ layer and generation of Fe-based oxides through evaporation.

• 한국분말재료학회지
• /
• 제14권5호
• /
• pp.287-291
• /
• 2007

Oxidation behavior and microstructural characteristics of nano-sized Sn powder were studied. DTA-TG analysis showed that the Sn powder exhibited an endothermic peak at $227^{\circ}C$ and exothermic peak at $560^{\circ}C$ with an increase in weight. Based on the phase diagram consideration of Sn-O system and XRD analysis, it was interpreted that the first peak was for the melting of Sn powder and the second peak resulted from the formation of $SnO_2$ phase. Microstructural observation revealed that the $SnO_2$ powder, heated to $1000^{\circ}C$ under air atmosphere, consisted of agglomerates with large particle size due to the melting of Sn powder during heat treatment. Finally, fine $SnO_2$ powders with an average size of 50nm can be fabricated by controlled heat treatment and ultrasonic milling process.

• 한국정밀공학회지
• /
• 제12권10호
• /
• pp.130-137
• /
• 1995

With the rapid growth of the die and mold, the new die making method has been developed. Especially, the laser is very useful, because it has a very fast cutting speed and is possible to manufacture complicated geometry. The quality of the laser cut is to be evaluated with respect to some characteristic quality parameters such as kerf width geometry, roughness and heat affected zone. This paper describes the laser cut characteristic(heat-affected zone) of the alloy tool steels(STD11) and the prediction of the kerf width genmetry by the FEM. On using the oxidation heat and laser beam, the prediction of kerf geometry is more accurate than that only by the laser beam. After laser cutting, the heat-affected zone is generated on the cutting cross section. The magnitude of hardness on the cutting cross section was similar to that of the heat treatment. It was possible to predict heat-affected zone by using the FEM program.

• 열처리공학회지
• /
• 제20권6호
• /
• pp.299-305
• /
• 2007

The effect of spray deposition of oxide particles on oxidation behaviors of as-cast Mo-14.2Si-9.6B (at%) alloys at $1200^{\circ}C$ up to for 100 hrs has been investigated. Various oxide powders are utilized to make coatings by spray deposition, including $SiO_2,\;TiO_2,\;ZrO_2,\;HfO_2$ and $La_2O_3$. It is demonstrated that the oxidation resistance of the cast Mo-Si-B alloy can be significantly improved by coating with those oxide particles. The growth of the oxide layer is reduced for the oxide particle coated Mo-Si-B alloy. Especially, for the alloy with $ZrO_2$ coating, the thickness of oxide layer becomes only one fifth of that of uncoated alloys when exposed to in air for 100 hrs. The reduction of oxide scale growth of the cast Mo-Si-B alloy due to oxide particle coatings are discussed in terms of the change of viscosity of glassy oxide phases that form during oxidation at high temperature.

• 한국주조공학회지
• /
• 제25권6호
• /
• pp.233-239
• /
• 2005

Contact material is widely used in the field of electrical parts. Ag-CdO has a good wear resistance and stable contact resistance. We studied a lifetime of Ag-CdO material because of getting better properties of Ag-CdO using Post-oxidation. The experimental procedure were melting using high frequency induction, heat treatment, rolling and internal oxidation. And we experimented on difference process, Post-oxidaion. Then we tested a lifetime and analysed. We obtained the optimizing oxidation temperature was $750^{\circ}C$. Using Pre-oxidation, coarse oxide and depleted oxidation layer existed but finer oxides were existed and depleted oxidation layer was not using Post-oxidation. In Post-oxidation, The density was 10 $g/cm^{3}$, the hardness was Hv 80 and the adhesive strength was 9000N. The specimen of Post-oxidation had better lifetime properties than that of Pre-oxidation. We predicted that the lifetime of Post-oxidation specimen is more longer twice than that of Pre-oxidation one.

• Preventive Nutrition and Food Science
• /
• 제7권2호
• /
• pp.179-183
• /
• 2002

Lycopene as a natural antioxidant may provide protection against a broad range of epithelial cancers and chronic diseases. Lycopene concentrate extracted from tomatoes can be used as functional food. Lycopene would undergo degradation via isomerization and oxidation under different processing conditions, which impact its bioactivity and reduce the fuuctionality for health benefits. Heat and light induce lycopene oxidation and isomerization of all-trans form to cis form. The effects of thermal treatment and light irradiation on the stability of lycopene were determined. Results have shown that lycopene stability depends on the extent of oxidation and isomerization. Cir-isomers are less stable than trans-isomers. The level of cis-isomers increased as treatment time increased but only for a short period during the beginning of the treatment. The major effect of thermal treatment and light irradiation was a significant decrease in the total lycopene content. A true assessment of health benefits of lycopene concentrate depends on the lycopene content and the composition of all trans-isomers and cia-isomers.