• Journal of Biosystems Engineering
• /
• v.5 no.2
• /
• pp.1-14
• /
• 1980

This study was carried out to investigate the effects of the counter-pressure setting and the roller speed of a rice whitening machine on the head rice recovery. milling capacity and milling efficiency, and also to find out the optimum operational conditions of the machine. The radial pressure inside the whitening chamber and the outlet axial pressure were measured to study their relationships with the head rice recovery, milling capacity and milling efficiency. The results of the study are summarized as follows. (1) The most important factor in rice whitening was the counter-pressure setting. It significantly affected the head rice recovery. (2) The roller speed significant affected the milling capacity and milling efficiency , but it did not affected the head rice recovery. (3) Both the radial pressure and the outlet axial pressure were affected by the counter-pressure setting but not by the roller speed. Both of them increased almost linearly with the counter-pressure setting. There was a significant correlation between the radial pressure and the outlet axial pressure. (4) The flow rate through the whitening chamber when the feed gate was fully opened increased with the roller speed, but it was not affected by the counter-pressure setting. (5) The head rice recovery decreased as the counter-pressure setting increased , but it was not affected by the roller speed. The reason could be explained by the fact that the radical pressure increased only with the counter-pressure setting. (6) The milling capacity increased with the counter-pressure setting and linearly with the roller speed. The milling efficiency generally increased with both the counter-pressure setting and the roller speed. However, the effect of roller speed was negligible at the higher counter-pressure setting. The temperature rise inside the whitening chamber was moderate with the mean of 11.3℃ (range 5.6-18.3℃) even though it increased slightly with the roller speed. Considering the head rice recovery and milling efficiency, the optimum operational conditions of the machine appeared to be the counter-pressure setting of 67g/㎠ and the roller speed of 1,050rpm. Neglecting the small difference in the head rice recovery , the greater milling capacity could be obtained at the counter-pressure setting of 85g/㎠ with the roller speed of 850-1050rpm.

• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.76-86
• /
• 1979

This study was conducted to find out the effects of rainfall occurring during the paddy sun-during process of traditional paddy harvesting operations on the quality of milld rice. Rice varieties used for the experiment were MINEHIJARI variety a japonica and SUWEON 264 vareity , a sister-line of TONG-IL . Sun-drying days after the paddy cutting, times of storm occurrance during sun-drying period, and storm duration were treated as variables. The results is summarised as follows : 1. Brown rice recovery exposed to rainfall during the sun-druing period were ranged 81.6-82.1% and 79.4-80.2% for MINEHIKARI and SUWEON 264 varieties, respectively. which showed negligible effect by rainfall. 2. Milling recovery of MINEHIKARI variety was not affected by storm duration but by the by the sun-drying days after cutting as the sun-drying days increased to eight and four days when the variety met the rainfall one and two times, respectively. The range of milling recoveries of MINEHIKARI variety were 75.18-74.07% and 75.24-73.46% as the variety met the rainfall one and two times, respectively, and it were estimated that up to 0.9% and 1.5% of milling recovery would be reduced by one and two times of rainfall during sun-drying period. 3. The milling recovery of SUWEON 264 variety was affected only by the increase of drying days after cutting when it met one time of rainfall during the sun-drying period, while it was begun to reduce by the storm duration more than 11hours as the drying paddy met two times of rainfall. The milling reveries of the paddy met one and two times of rainfall were ranged 74.24-73.21% and 74.02-72.36% which were estimated to be reduced up to 0.9 % and 1.8% by the increase of the drying days after cutting and storm duration , respectively. 4. The head rice recovery of MINEHIKARI rice variety showed notable decrease as the drying days after cutting increased, and also it was greatly reduced even by the five hours of storm duration when one time of rainfall occurred but it was not affected by storm duration when the rainfall occurred two times. Head rice recoveries of MINEHIKARI met one and two times of rainfall during the sun-drying period were 65. 15 -40.85% and 61.86 - 30.03 %, which showed terrible reduction as much as up to 25% and 35% compared to that which did not met rainfall during the sun-drying process. 5. Head rice recovery or SUWEON 264 variety was very much reduced as the sum-drying days after cutting increased. Storm duration less than five hours during the sun-drying process did not affect on the decrease of head rice recovery when the variety was exposed to one time of rainfall, while storm duration affected considerably on the reduction of head rice recovery of SUWEON 264 variety exposed to two times of rainfall. The range of head rice recovery, 56.43 - 33.94% and 51.28 - 21.03% , for the paddy exposed to rainfall one and two times were evaluated that up to 24% and 37% of reduction in head rice recovery would be brought about compared to the head rice recovery of the sundriedpaddy that did not met the rainfall.

• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.75-75
• /
• 1979

This study was conducted to find out the effects of rainfall occurring during the paddy sun-during process of traditional paddy harvesting operations on the quality of milld rice. Rice varieties used for the experiment were MINEHIJARI variety a japonica and SUWEON 264 vareity , a sister-line of TONG-IL . Sun-drying days after the paddy cutting, times of storm occurrance during sun-drying period, and storm duration were treated as variables. The results is summarised as follows : 1. Brown rice recovery exposed to rainfall during the sun-druing period were ranged 81.6-82.1% and 79.4-80.2% for MINEHIKARI and SUWEON 264 varieties, respectively. which showed negligible effect by rainfall. 2. Milling recovery of MINEHIKARI variety was not affected by storm duration but by the by the sun-drying days after cutting as the sun-drying days increased to eight and four days when the variety met the rainfall one and two times, respectively. The range of milling recoveries of MINEHIKARI variety were 75.18-74.07% and 75.24-73.46% as the variety met the rainfall one and two times, respectively, and it were estimated that up to 0.9% and 1.5% of milling recovery would be reduced by one and two times of rainfall during sun-drying period. 3. The milling recovery of SUWEON 264 variety was affected only by the increase of drying days after cutting when it met one time of rainfall during the sun-drying period, while it was begun to reduce by the storm duration more than 11hours as the drying paddy met two times of rainfall. The milling reveries of the paddy met one and two times of rainfall were ranged 74.24-73.21% and 74.02-72.36% which were estimated to be reduced up to 0.9 % and 1.8% by the increase of the drying days after cutting and storm duration , respectively. 4. The head rice recovery of MINEHIKARI rice variety showed notable decrease as the drying days after cutting increased, and also it was greatly reduced even by the five hours of storm duration when one time of rainfall occurred but it was not affected by storm duration when the rainfall occurred two times. Head rice recoveries of MINEHIKARI met one and two times of rainfall during the sun-drying period were 65. 15 -40.85% and 61.86 - 30.03 %, which showed terrible reduction as much as up to 25% and 35% compared to that which did not met rainfall during the sun-drying process. 5. Head rice recovery or SUWEON 264 variety was very much reduced as the sum-drying days after cutting increased. Storm duration less than five hours during the sun-drying process did not affect on the decrease of head rice recovery when the variety was exposed to one time of rainfall, while storm duration affected considerably on the reduction of head rice recovery of SUWEON 264 variety exposed to two times of rainfall. The range of head rice recovery, 56.43 - 33.94% and 51.28 - 21.03% , for the paddy exposed to rainfall one and two times were evaluated that up to 24% and 37% of reduction in head rice recovery would be brought about compared to the head rice recovery of the sundriedpaddy that did not met the rainfall.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• v.4 no.2
• /
• pp.1-8
• /
• 1979

This study was carried out to investigated the actual state of rice milling at local milling plants and to find out sources for elevating their milling recoveries in both quantity and quality. At 36 local milling plants located in Gyeongnam and Jeonnam , milling recoveries and head rice recoveries were measured with respect to their different milling systems and rice varieties. Then, the same samples of rice were milled by experimental milling equipments at laboratory, and the two experimental results were compared in order to determine the amount of milling recovery possibly to be increased. The results of this study are as follows ; 1. Milling recoveries of rice at local milling plants were proved to have no relationship with milling systems, and were 68.1% per ent and 72.6percent on an average with new variety and native variety, respectively. 2. The milling recoveries above stated can be elevated 4.5 percent and 2.9percent with new variety and native variety, respectively, by developing and extending technologies of manufacturing and handling rice milling machinery. 3. The head rice recovery of new variety at local milling plants has insignificant differences among milling systems, and was 54.8 percent on the average. With native variety, the recovery by friction type rice polisher was 0.9percent higher than that of friction-abrasive type polisher, and was 64.9 percent on the average. 4. The head rice recoveries of new variety and native can be elevated 5.1percent and 3.9percent, respectively, by the same stimulation above mentioned.

• Journal of Biosystems Engineering
• /
• v.3 no.2
• /
• pp.88-99
• /
• 1978

In this study, rice harvesting systems suitable to Korean situations and the optimum timing of these systems were determined, respectively, based on experimentally determined factors such as filed yield and the milling quantity and quality measured at various levels of the grain moisture content at harvest. Rice varieties used for the experiment were the AKIBARE (Japonica-type) and the SUWEON 251 (high yielding TONGIL sister-line variety), The harvesting systems studied by the experimental work of this study were traditional system with both the wet material and dry-material threshing system by use of binder with both the dry-material and wet-material threshings, and system by use of combine. Grain samples were taken from final products of the paddy rice harvested from the experiment a fields for each system to measure the recovery rates of the milled rice. The results may be summarized as follows; 1. The milling recovery rate of the AKIBARE variety had highest value within the range of the grain moisture at harvest, showing from 21 to 26 percent. The head-rice recovery for the same variety was a little greater in the wet-material threshing than in the dry-material threshing , higher values of which , were 20 to 25 percent , seen within the range of grain moisture at harvest regardless of the harvesting systems tested. 2. The milling recovery of the SUWEON 251 , when tested for different harvesting systems and harvesting grain moisture, did not show a statistically significant different. In contrast , head-rice recovery for the systems operated by the wet-material threshing was much greater than that by the -material threshing. The difference of the recoveries between these systems range from 2.6 to 4.7 percent. 3. An assessment of the optimum period of -harvest timing for each of the harve\ulcornersting systems tested were made bJ.sed on (a) the maximum total milled-rise yield and (b) the percentage reduction in the total milled-rice yield due to untimely harvest operations. The optimum period determined are: 23-19% for the ATD, AC, STD, SBW, STW systems, 25-21% for the ATW ani ABW systems, and 27-18% for the ABD, SBD, and SC systems, respectively.

• Journal of Biosystems Engineering
• /
• v.20 no.3
• /
• pp.262-274
• /
• 1995

A rice mill pilot plant was designed and developed in the basis of the simulation results on the mill plants. The performance of the developed rice mill plant was evaluated, and the simulation model on the mill system was validated with the experimental data in the mill plant. The results of this study were as followings : 1. A rice mill pilot plant with the capacity of 0.5 t/h was designed and developed. 2. The hulled ratio of the mill plant was 87.3%, and the milled rice recovery and the head rice recovery of the cleaned rice were 74% and 87% , respectively. The degree of milling of the cleaned rice was 10.6% with a high polish. The intensity of the cleaned rice appeared high compared with that of the milled rice in the analysis of whiteness test using an image processing system. 3. The bottleneck, processing time, and production amount of the developed mill system almost coincided with those of the simulation of the rice mill plant. The developed simulation model of the rice mill plant was proven to be applicable to the design of a rice mill plant through experiments.

• Journal of Biosystems Engineering
• /
• v.3 no.1
• /
• pp.47-63
• /
• 1978

This study was conducted to obtain a basic information necessary to assess present rice milling technology in Korea The profiles for milling plants was analyzed by survey work.For the private custom-work mills, which process about 80 percent of domestic rice consumption ,their actual milling test for the identical samples as used for filed mills was conducted. Two rice varieties Japonica and Tongil-type were associated with the experiments. The results are summarized as follows: 1. Analyses for private custom-work mills showed their general aspects as; about 91 percent of the mills belonged to an individual owner ship ; more than 93 percent of the mills was established earlier than 1950 ; about 80 percent of the mills was powered with electric motor; mills having less than two employees were about 75 percent; about 45 percent of the mills provided for warehouse in storing customers cereal grains. 2. The polishers installed in 1,255mills within the surveyed area (7 counties) have been supplied by 44 different domestic manufacturers ;in but about 60 percent of which was supplied by 6major manufacturers. The polishers could be classified into two categories in terms of principles of their polishing actions ;jet-pearler and friction types. About 51 percent of the mills was equipped with the former which has been recognized as giving greater milling recovery than the friction types. 3. Reason for owners of private mills to supplement new machines was due mainly to pgrading their mills to meet the requirements that established by the Government. However, about 60 percent of the mill owners intended to replace with new pearler by their own needs to meet with new high yielding varieties. 4. Processing systems of each previate rice mills surveyed could be classified into three categories, depending upon whether the systems posessed such components as precleaner and paddy separator or not. Only 36.7 percent of mills was installed with both precleanr ad paddy seperrator, 5.0 percent of mills did have neither percleaner nor paddy seperator, and rest of them equipped only one of the two. Hence,it is needed for about 63% of rice miils to be supplemented with these basic facilities to meet with the requirements for the standaized system. 5. Actual milling capacity measured at each field rice mills was shown a wide variation, having range from about 190 to 1,210 kg/hr. The percentages of mills classified according to daily milling capacity based on this hourly capacity were 24.3% for the capacity less than 3 M/T a day; 20.0% for 3-4 M/T; 15.6% for 4-5 M/T; 6.7% for 5-6 M/T; 22.3% for 6-7 M/T; and 11.0% for more than 7 M/T a day. 6. Actual amount of rice processed was about 310 M/T a year in average. About 42% of total milled rice was processed during October to Decembear, which formed a peak demand period for rice mills. The amount of rice milled during January to May was relatively small, but it had still a large amount compared to that during June to September. 7. Utilization rate of milling facility, i. e., percentage of the actual amount of milled rice to the capacity of rice mills, was about 18% on the year round average, about 41% in the peak demand season, and about 10% during June to September. Average number of operating days for mills surveyed was about 250 days a year, and about 21 days a month. 8. Moisture contents of paddy at the time of field mill tests were ranged 14.5% to 19.5% for both Japonica and Tong-i] varieties, majority of paddy grains having moisture level much higher than 1530. To aviod potential reduction of milling recovery while milling and deterioration of milled rice while storage due to these high grain mJisture contents, it may be very important for farmers holding rice to dry by an artificial drying method. 9. Milling recovery of JapJnica varieties in rice mills was 75.0% in average and it was widely ranged from 69.0% to 78.0 % according to mills. Potential increase in milJing recovery of Japonica variety with improvement of mill facilities was estimated to about 1.9%. On the other hand, milling recovery of Tong-il varieties in the field mill tests was 69.8% in average and it ranged from 62% to 77 %, which is much wider than that of Japonica varieties. It is noticed that the average milling recovery of Tong-il variety of 69.8% was much less than that of the Japonica-type. It was estimated th3.t up to about 5.0% of milling recovery for Tong-il variety could be improved by improving the present lo'.ver graded milling technology. 10. Head rice recoveries, as a factor of representing the quality of commercial goods, of Japonica and Tong-il varieties were 65.9% and 53.8% in average, and they were widely ranged from 52% to 73% and from 44% to 65% , respectively. It was assessed that head rice recovery of Japonica varieties can be improved up 3.3% and that of Tong-il varieties by 7.0% by improving mill components and systems.

• Journal of Biosystems Engineering
• /
• v.2 no.1
• /
• pp.56-80
• /
• 1977

This experimental work was conducted in order to find out the optimum time of harvest of Japonica-type (Akibare) and Indica-type(Tong-il) rice variety for three harvesting systems by investigating the harvesting losses and milling quality. The study was also concerned about the nature and amount of grain losses incurred during the each sequence of post-harvest technologies, and based on these result, a modification of existing systems giving a minimum grain loss was attempted. Binder, combine, and traditional systems were tested in this study and five grain moisture levels were disposed according to the decrease of grain moisture . The results are summarized as follows ; 1. The total losses of Akibare variety were ranged from 1.1 to 1.5 per cent for the traditional harvesting system , 2.1 to 4.8 per cent for the harvesting system by use of binder, and 2.8 to 4.3 per cent for the harvesting system by use of combine as the grain moisture content was reduced from 24 to 15 percent. Milling recovery of the harvesting system by use of binder, 74.8 ∼75.7 percent, was a little higher as it was compared to that of traditional harvesting system, 74.3 ∼75.0per cent, and that of the harvesting system by use of combine, 73.8 ∼75.0 per cent. Head rice recovery of mechanically dried paddy samples was higher than that of sun-dried paddy samples. 2. The total losses of Tong-il variety were ranged from 3.8 to 5.0 per cent for the traditional harvesting system, 5.2 to 10.0 percent for the system by use of binder, and 3.0 to 5.0 per cent for the system by use of combine as the grain moisture was reduced from 28 to 16 per cent. 3. Milling recovery of Tong-il variety harvested by the traditional harvesting system was 72.3 ∼73.6 percent and it was lower when compared to that of 72.3∼75.0 per cent harvested by binder, and 73.0∼74.6 percent harvested by combine. 4. Head rice recovery of Tong-il variety harvested by the traditional harvesting system (58.