• Korean Journal of Materials Research
• /
• v.8 no.4
• /
• pp.354-358
• /
• 1998

Effect of cold drawing ratio and aging time on the hardness of lnconel 718 wire aged at 11l6K were investi¬gated by hardness measurement and scanning & transmission electron microscopy. Hardness which was 245Hv in as¬solution treated condition increased very rapidly to 450Hv as cold drawing ratio increased to 50%. The hardness in the early stage of aging was increased by the precipitation of $\gamma^{'}$ and $\gamma^{'}$ phases and after the peak hardness, the hardness was decreased by the transformation of $\gamma^{'}$ phase to $\delta$ phase. The time to reach peak hardness during aging appeared to be reduced with the increase of cold drawing ratio, and those times were 30, 10, and 5 minutes for 0, 30 and 50% cold drawn materials, respectively. For the 50% cold drawn material. $\gamma^{'}$ and $\gamma^{'}$ were precipitated by aging for 5 minutes at 1116K. The hardness in the same material was largely decreased under the initial hardness by the recrystallization.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.105-106
• /
• 2007

Microstructure and hardness of metallic powder of Cu was studied after high pressure torsion (HPT) with 10 torsions and high pressure of 6 GPa. The size Cu grain decreases drastically after HPT and reaches the nano size range. During HPT, Cu powder increases hardness and Hall-Petch hardening, due to the decreasing grain size. In this study, effect of HPT on the hardness of Cu powders and consolidation with Nanocrystalline of the work reported here. The results indicated that Cu powder has a beneficial effect on homogeneous deformation, reducing grain size.

• Korean journal of food and cookery science
• /
• v.10 no.4
• /
• pp.346-350
• /
• 1994

This investigation was undertaken for the purpose of studying the effect of the addition of the powder(0, 1, 2, 3%)from fruit of paper mulberry(Broussonetia Kazinoki SieboId) on the hardness, cohesiveness, elasticity, gumminess, chewiness, cooking loss and sensory characteristics of cooked ground beef with or without soysauce. The results obtained were summerized as follows; Hardness, gumminess, chewiness, and cooking loss were decreased by increasing the percent of adding the powder from the fruit of paper mulberry. As a result of sensory evaluation for cooked ground beef, sample with powder from the fruit of paper mulberry showed the higher scores in most of the characteristics. And cooked ground beef added the powder from the fruit of paper mulberry with soysauce showed the higher decreasing rate of hardness than those of without soysauce.

• Journal of Ocean Engineering and Technology
• /
• v.5 no.2
• /
• pp.58-66
• /
• 1991

Not only difference of fatigue crack growth and propagation behavior resulted from the grain size, the hardness ratio and volume fraction in M.E.F. dual phase steel composed of martensite in hard phase and ferrite in soft phase, but also the effects of the plastic constraint were investigated by fracture mechanics and microstructural method. The main results obtained are as follows: 1) The fatigue endurance of M.E.F. steel increases with decreasing the grain size, increasing the ratio of hardness and volume fraction. 2) The initiation of slip and crack occures faster as the stress level goes higher. These phenomena result from the plastic constraint effect of the second phase. 3) The crack propagation rate in the constant stress level is faster as the grain size gets larger, the ratio of hardness lower and volume fraction smaller.

• Journal of Power System Engineering
• /
• v.18 no.3
• /
• pp.100-105
• /
• 2014

This study is to investigate the effect of thermo mechanical treatment on the mechanical properties of 316L stainless steel. ${\alpha}^{\prime}$ and ${\varepsilon}$-martensite was formed by deformation. With increasing number of thermo mechanical treatment, volume fraction of martensite was increased rapidly, and then unchanged. With increasing number of thermo mechanical treatment, hardness and strength was increased rapidly, and then unchanged while elongation was decreased rapidly, and then unchanged. With increasing volume fraction of martensite formed by thermo mechanical treatment, hardness and strength was increased rapidly, elongation was decreased rapidly. Thus, hardness, strength and elongation of thermo mechanical treated 316L stainless steel was strongly affected by martensite formed by thermo mechanical treatment. Good combination of strength and elongation was obtained from thermomechanical treatment.

• Journal of Ginseng Research
• /
• v.19 no.3
• /
• pp.287-290
• /
• 1995

This study was conducted to elucidate the effect of physical properties of soil in nursery bed with different densities on growth of ginseng seedling. Stem length, leaf length and leaf width of ginseng seedling showed the decreasing tendency with increasing the hardness of the nursery soil. Fresh root weight per seedling and number of available seedlings were increased significantly with decrease of the soil hardness. For solid, liquid phases, bulk density and hardness of soil, negative correlations were shown in stem length, leaf length, leaf width, root weight per seeding, and number t of available seedlings. On the other hand, gas phase, air permeability and porosity of soil had positive correlations with stem length, leaf length, leaf width, root weight per seedling and number of available seedlings. Key words Yang-Jik nursery, ginseng seedling, soil physical properties.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.1
• /
• pp.28-39
• /
• 2004

The effect of trace metallic additives on microstructure, surface appearance and hardness of zinc electrodeposits was investigated by using sulfate bath and flow cell system. The preferred orientation of Zn deposit with Fe additive was (103)(104)+(002) mixed texture and that of Zn deposits with both Fe-Ni and Fe-Co additives was (10 1), while Zn deposits with Fe-Cr additives had (002) preferred orientation. The surface morphology of the zinc deposits was closely related to the preferred orientation of the deposits. The glossiness of Zn deposit with Fe-Ni additives was higher than that of pure Zn deposit, while the glossiness of Zn deposits with both Fe-Co and Fe-Cr additives was lower than that of pure Zn deposit. The hardness of Zn deposits with both Fe-Ni and Fe-Co additives was noticeably higher than that of Zn-Fe deposit, while that of Zn deposit with Fe-Cr additives was similar to that of Zn-Fe deposit.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.4
• /
• pp.236-240
• /
• 2004

Effect of plasma power on PECVD process were investigated in this study. TiN and TiCN films were deposited on nitrided STD11 steel with 600W, 1,200W and 1,600W plasma power. As the plasma power was increased, the preferred orientation was reinforced from (200) to (111) and the hardness of films was improved. The low plasma power was, however, effective for improving of adhesion force of films. Regarding above properties, TiN and TiCN films were deposited by gradient plasma power. It was possible to get high hardness as well as adhesion force through gradient plasma power.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.3
• /
• pp.17-23
• /
• 2003

As a fundamental study of developing sawdust board from thinning softwood logs from three species (Pinus densiflora S. et Z., Larix leptolepis G. and Pinus koraiensis S. et Z.), this study examined the effect of board density and resin content on physical and mechanical properties of sawdust board. As the board density increase, thickness swelling, bending strength, and Brinell hardness increased while water absorption decreased. With increasing the resin content, the bending strength and hardness increased while water absorption and thickness swelling decreased. The board made of L. leptolepis was slightly low in its water absorption, and the one made of P. koraiensis was a little high in its bending strength, while there was no definite difference between each kind of trees in their hardness values.

• Archives of Metallurgy and Materials
• /
• v.66 no.4
• /
• pp.1049-1054
• /
• 2021

In this study, stainless steel 316L and Inconel 625 alloy powders were additively manufactured by using directed energy deposition process. And heat treatment effect on hardness and microstructures of the bonded stainless steel 316L/Inconel 625 sample was investigated. The microstructures shows there are no secondary phases and big inclusions near interfacial region between stainless steel 316L and Inconel 625 except several small cracks. The results of TEM and Vickers Hardness show the interfacial area have a few tens of micrometers in thickness. Interestingly, as the heat treatment temperature increases, the cracks in the stainless steel region does not change in morphology while both hardness values of stainless steel 316L and Inconel 625 decrease. These results can be used for designing pipes and valves with surface treatment of Inconel material based on stainless steel 316L material using the directed energy deposition.