• Tribology and Lubricants
• /
• v.20 no.6
• /
• pp.322-329
• /
• 2004

Recently, a load/unload(L/UL) system is adopted to the hard disk drive(HDD) due to its advantages such as lower power consumption, larger data zone, simpler fabrication of disk due to no bumped parking zone, and rarer contact between slider and media. An analysis of the transient motion for the slider is very important to design an air bearing surface(ABS) of the slider to secure the stable performance of the system. During the L/UL process, however, there are several issues occurred such as contact or collision between slider and media. Sometimes this will cause the system failure. In this study, the dynamics of a pico slider during the loading process are investigated through numerical simulation using FEM analysis and experiment. Ramp profile and angular velocity of the swing arm actuator are very important parameters for the design of L/UL system to avoid collision between slider and disk.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2646-2653
• /
• 2000

The performance of slider of a hard disk drive affects the durability of the system. Particularly, the flying ability of the slider is critical in terms of surface damage and head crash. In this work, the take-off characteristics of the slider for various types of laser zone textured bump geometries were investigated. Also, the effect of ambient pressure on the flying characteristics of the slider was experimentally observed. An index of air density which can be used as a parameter for evaluating the flying characteristic is introduced.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.210-214
• /
• 2003

The static and dynamic characteristics of HDD slider with ulta-low flying height are analyzed using Direct Numerical method with Boundary Fitted Coordinate System. The slip flow effect is considered using the Boltzmann equation solution in a form of the flow rate database. The air film stiffness and damping are evaluated by the small perturbation method.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.363-371
• /
• 2000

There are some concepts that could achieve Near-Field Recording (NPR). One of concepts is the use of the flying head with Solid Immersion Lens (SIL). The basic concept of this is almost same with that of Hard Disk Drive (HDD). This study presents the flying characteristics of the slider for NFR. Numerical simulations are performed using FEM and Broydon-Fletcher-Goldfarb-Shanno (BFGS) method. Some modifications are considered to improve flying characteristics of the slider.

• Tribology and Lubricants
• /
• v.16 no.4
• /
• pp.247-252
• /
• 2000

As the demand for higher areal recording densities requires a lower flying height of the slider, the variation of the flying height of the slider during drive operation becomes of great concern. The variation of the flying height is closely related with the slider design parameters such as air bearing shape, cavity depth, shallow step depth, crown, camber, pitch offset, roll offset, gram load, and so on. The objective of this work is to optimize the cavity depth and the shallow step depth, which are the control factors in air bearing design, using Robust Design method. It was found that the shallow step depth was statistically significant in affecting the variation of flying height, therefore the level of the shallow step depth should be chosen to minimize the variation of flying height.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.167-174
• /
• 1998

In this work the surface damage of head and disk of a hard disk drive was analysed using an Atomic Force Microscope. The initial damage of the disk occurred by generation of extremely small wear particles. Also it was shown that wear particles tend to pile up near the front side of the slider. The surface damage mechanism of drag test and contact-start-stop test was found to be quite similar.

• KSTLE International Journal
• /
• v.1 no.1
• /
• pp.29-33
• /
• 2000

In this study, a methodology is developed and confirmed to find the physical contact between the slider and disc due to the defects of disk during head seeking operation using acoustic emission (AE) signal. The head/disk contact was detected during random and standard seeks, whereas no contact was detected during track fellowing. During standard and random seeks, the torsion mode of slider excitation was observed at 680KHz. Therefore, it is thought that AE technique can be used as an alternative method of the glide test by monitoring existence of the torsional mode of the slider during seek operation or can be used to detect the spacing loss during seeking operation. By appropriately choosing the location of the sensor an order of magnitude increase in the sensitivity for RMS AE signal is observed. Therefore we can find take-off velocity clearly with high signal to noise ratio of AE signal.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.314-317
• /
• 2005

There are many benefits such as increased areal density, reduced power consumption, applied smaller size and improved shock resistance in Load/Unload(L/UL) mechanism. It has been the key technology of developing small form factor hard disk drive used in portable digital devices. The main objectives of L/UL are no slider-disk contact and faster L/UL process. For realizing those, we must consider many design parameters in L/UL systems. In this paper, we focus on the effects of ramp profile. We can investigate dynamic characteristics of suspension tap and slider on ramp during unloading process experimentally. In special, we examine the effects of vortical velocities, ramp slopes and disk vibrations. As the result of these experiments, we propose design criteria of advanced ramp profile for good unloading performance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.8
• /
• pp.1069-1076
• /
• 2002

Contamination particles in a hard disk drive can cause serious problems including slider crash and thermal asperities. A recirculation filter is typically installed in the hard disk drive to remove the particles. Measurements and theoretical predictions of particle concentration decay with the filter are carried out for a commercially available HDD. Especially, the effect of disk rotational speed on the particle capture efficiency is investigated. Results show that filter efficiency is higher for higher disk rotational speed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.5 s.236
• /
• pp.599-608
• /
• 2005

Controlling particle contamination is important to increase storage capacity as the flying height of a slider in a hard disk drive decreases. Since precise detection and analysis of particles are primary steps of particle control in a HDD, many researchers have used sampling methods. In this paper, we newly designed a particle sampler and conducted performance evaluation of the sampler. Also, we conducted particle sampling from the HDD using the particle sampler and analysis of sampled particles by SEM and AES. Experimental results show that the particles generated by the slide-disk interaction mainly came from the disk surface.