• Progress in Superconductivity and Cryogenics
• /
• v.4 no.1
• /
• pp.40-44
• /
• 2002

Influences of bending strain on the critical current (Ic) were investigated in Bi-2223 superconducting tapes at 77K. The effect of bending mode on the Ic degradation behavior was discussed in viewpoints of test procedure, n-value and damage morphology Especially, in this paper, we reported the Ic behavior in Ag alloy/Bi-2223 multifilamentary superconducting tapes under bending occurred within a width plane of the tape which was called as a hard bending. The Ic degradation under hard bending appeared significantly as compared with that under easy bending. The n-value decreased slightly with the increase in bending strain under the hard bending.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.2
• /
• pp.8-11
• /
• 2012

In order to recognize the allowable bending diameter in coils, the strain as function of diameters is evaluated. The irreversible strain limits of $I_c$ in the easy and hard bending modes were measured. Strains were calculated at the coating film in the easy bending and at outer edge or inner edge in the hard bending of the CC tape, respectively. The tape geometry subjected to bending procedures is considered from the current industrial spool winding operation. Through the linear superposition of strain induced in different bending modes regarding the expressions, the appropriate design for critical bending diameter is suggested. Results proved that the existence of buckling resulting from bending in hard direction when applied strain exceeded 0.6% is possible. The depicted results showed that the strain limit as a viable parameter should be considered for future purposes.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.144-148
• /
• 2002

Influences of bending strain on the critical current (I$_{c}$) were investigated in Bi-2223 superconducting tapes at 77K. The effect of bending mode on the I$_{c}$ degradation behavior was discussed in viewpoints of test method, n-value and damage morphology. Especially, in this paper, we reported the I$_{c}$ behavior in Ag alloy/Bi-2223 multifilamentary super- conducting tapes under bending occurred within width x length plane of the tape which was called as a hard bending.nding.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.04a
• /
• pp.50-54
• /
• 2002

Influences of bending strain on the critical current ($I_c$) in Ag-sheathed Bi-2223 superconducting tapes at 77K were investigated. The effect of bending mode on the bending strain characteristics was discussed in viewpoints of sample geometry, n-value and damage morphology. Especially, in this paper, we reported the $I_c$ behavior in Ag alloy sheathed Bi-2223 multifilamentary superconducting tapes under hard bending. As a result, $I_c$ degradation behavior of the hard bending appeared remarkably than the case of easy bending, but it did not influence greatly on the n-value.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.70-74
• /
• 2004

We investigated transmittance, surface characteristics, and resistivity according to bending of ITO(indium tin oxide) film with four other multi -harrier film). Transmission data of ITO film with four ITO films showed there was about large 90％ transmission above 550nm wavelength at three multi-barrier structures. But, both-side hard coated structure showed relatively low 75％ transmission above 550nm wavelength. And, surface images measured from SEM (scanning electron microscope) showed both-side hard coated structure have a tendency of more roughness. Also, resistivity change of four other multi-barrier film showed there was the lowest change at one-side hardcoated structure. Subsequently, with result of resistivity change according to position, we knew the resistivity change of the center increased rapidly than that of the edge.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.55-62
• /
• 2019

Stiffness-gradient stretchable electronic packages of the soft PDMS/hard PDMS/FPCB structure were processed using the polydimethylsiloxane (PDMS) as the base substrate and the more stiff flexible printed circuit board (FPCB) as the island substrate. The elastic characteristics of the stretchable packages were estimated and their long-term reliabilities on stretching cycles and bending cycles were characterized. With 0.28 MPa, 1.74 MPa, and 1.85 GPa as the elastic moduli of the soft PDMS, hard PDMS, and FPCB, respectively, the effective elastic modulus of the soft PDMS/hard PDMS/FPCB package was estimated as 0.6 MPa. The resistance of the stretchable packages varied for 2.8~4.3% with stretching cycles ranging at 0~0.3 strain up to 15,000 cycles and for 0.9~1.5% with 15,000 bending cycles at a bending radius of 25 mm.

• Progress in Superconductivity and Cryogenics
• /
• v.12 no.2
• /
• pp.5-8
• /
• 2010

In this study, the effect of bending strain on the transport property and critical current of lap and butt-jointed (non-laminated) BSCCO tapes has been investigated. The samples were joined using a mechanically controlled jointing procedure. To achieve a uniform thickness at the joint a single point loading contact has been devised. GFRP mandrels with different bending radii which support the sample during bending have been used. $I_c$ have been measured at 77 K and self field. In the case of easy bending test for jointed BSCCO tapes, sudden degradation of $I_c$ is caused by the local strain concentration due to non uniform deformation at the edge parts of the joint. In the case of hard bending test of jointed BSCCO tapes transverse macroscopic crack at specific subsection caused a large $I_c$ degradation. The transport property of jointed BSCCO tapes in each bending mode was discussed with the damage morphology occurred.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.209-214
• /
• 2001

Most reinforce concrete Columns of Building structure are subjected to both axial load and biaxial bending. However, It is hard to estimate the moment capacity of biaxial bending by exact solution. Thus, columns under biaxial bending are designed by approximate methods in practice. The purpose of this study is to compare experimental result with approximate methods and exact solution by computer. Parameters of the present test are compressive strength of concrete (350, 585, 650kgf/$\textrm{cm}^2$) and shape ratio of rectangular section. Ultimately, an experimental shape factor for rectangular RC column section is obtained through the test program. The shape of load contour is dominated by this shape factor obtained experimentally. So, reasonable design of RC columns subjected to both axial compression and biaxial bending depends on load contour.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.177-180
• /
• 2003

We investigated transmittance, surface characteristics, and resistivity according to bending of ITO(indium tin oxide) film with four other multi-barrier film. Transmission data of ITO film with four ITO films showed there was about large 90% transmission above 550nm wavelength at three multi-barrier structures. But, both-side hard coated structure showed relatively low 75% transmission above 550nm wavelength. And, surface images measured from SEM(scanning electron microscope) showed both-side hard coated structure have a tendency of more roughness. Also, resistivity change of four other multi-barrier film showed there was the lowest change at one-side hardcoated structure. Subsequently, with result of resistivity change according to position, we knew the resistivity change of the center increased rapidly than that of the edge.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.46-57
• /
• 2006

To estimate nondestructively strength performances of laminated woods, 3-ply parallel- and cross-laminated wood specimens exposed under atmosphere conditions after bending creep test were prepared for this study. The effects of density of species, arrangement of laminae and lamination types on dynamic MOE obtained by flexural vibration were investigated, and regression analyses were conducted in order to estimate static bending strength and bending creep performances. Dynamic MOE of parallel-laminated woods showed 1.0~1.2 times higher values than static bending MOE, and those of cross-laminated woods showed 1.0~1.4 times higher values than static bending MOE. The degree of anisotropy of dynamic MOE perpendicular to the grain of face laminae versus that parallel to the grain of face laminae was markedly decreased by cross-laminating. There were strong correlations between dynamic MOE by flexural vibration and static bending MOE (correlation coefficient r = 0.919~0.972) or bending MOR (correlation coefficient r = 0.811~0.947) of 3-ply laminated woods, and the correlation coefficient were higher in parallel-laminated woods than in cross-laminated woods. It indicated that static bending strength performances were able to be estimated from dynamic MOE by flexural vibration. Also, close correlations between the reciprocal of dynamic MOE by flexural vibration and initial compliance at 0.008 h of 3-ply laminated woods were found (correlation coefficient r = 0.873~0.991). However, the correlation coefficient between the reciprocal of dynamic MOE and creep compliance at 168 h of 3-ply laminated woods was considerably lower than those between dynamic MOE and initial compliance, and it was hard to estimate creep compliance with a high accuracy from dynamic MOE due to the variation of creep deformation.