• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.4
• /
• pp.51-57
• /
• 1990

There exist residual stresses and deformations in welded structures because of nonuniform temperature distribution. The thermal elasto-plastic analysis is necessary to describe the behavor of the structure during welding. In this paper, we calculated the residual stresses and deformations of the welded beam using the I-dimensional layered beam theory. In the previous 1-dimensional analyses, there were restrictions that the equilibrium conditions which were effective only on beams with infinite length were used, and the boundary conditions could not be considered adequately. But, the layered beam theory based on the incremental finite element method, can overcome these restrictions. On the other hand, in the 2-dimensional analysis, the computing time is large because of many degrees of freedom, and there was inaccuracy in the calculation of welding deformations. However, the layered beam theory can take into account the variation of properties along the depth, and can reduce the degrees of freedom considerably in comparision with the 2-dimensional analysis, and shows good agreement with the experiments.

• Journal of Welding and Joining
• /
• v.34 no.6
• /
• pp.55-61
• /
• 2016

Recently developed ferritic heat resistance steel, T24 was used to evaluate microstructure characteristics of simulated heat affected zone. Also, correlation between the prior austenite grain size and amount of $M_{23}C_6$ carbide dissolution was discussed. With the increasing of peak temperature, Grain size steadily increased up to $1050^{\circ}C$ and then rapidly increased at $1150^{\circ}C$. Of the peak temperature $950{\sim}1050^{\circ}C$, amounts of $M_{23}C_6$carbide dissolution are low. But Most of $M_{23}C_6$ carbide that is inhibited grain growth were dissolved above $1050^{\circ}C$ and decreased volume fraction of carbide. This indicates that grain growth may be achieved through dissolution of carbide in the base material. As of welding, due to very rapid heating rate, $M_{23}C_6$ carbide exists above equilibrium solution temperature that is $800^{\circ}C$, even at $1050^{\circ}C$. So, It was confirmed that close correlation between carbide dissolution in the base material and grain growth. Calculated grain size has a linear relationship with peak temperature, on the other hand, measured grain size discontinuously increased between $950{\sim}1050^{\circ}C$ and above $1050^{\circ}C$. Grain size of heat affected zone at $1350^{\circ}C$ peak temperature showed maximum 67um and minimum 4um. Also, The number of side showed 3 to 10.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.5
• /
• pp.487-492
• /
• 2010

In this study, our system that the volume of collected human waste in the septic tank truck is measured accurately and the fee of disposing human waste can be calculated by using measured results has been developed. The level sensor and its circuits which can measure the height of the tank, the hand-held system that can be used by workers easily and simply with micro-controller have been developed. Also, this system has been built in the receipt printing function to charge for disposal fee. Even when working on a sloping field, this system can measure the accurate collected volume of human waste in the tank using the X-Y axis angle sensor. The results of this study expect that the popular complaints that generated from human waste can be reduced, the exportation possibility of our specialized systems can acquire foreign currency.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.17 no.4
• /
• pp.1-14
• /
• 2015

This study mainly analyzes that designing patterns of an adult women Jeogori that takes advantage of patterns from each textbooks and complements the disadvantages based on the analysis of data from the dress evaluation and comparison of materials. The modification of a size specification is needed for the standard body as an adjust of the length of Jogori between front and back, mediation for bust width between front and back, a movement for the based line of Sup and Godae. As a result, the suitable pattern according to the standard somatotype is as below. Jeogori Length of front is determined by the length of back which was measured from side neck point to bust point plus three centimeters, and give three and half centimeters more in front. This three and half centimeters is for the curved in front of your body due to the chest. Bust width of front and back have to show the differences of human body. Bust width of front is calculated as bust girth into quarters and add two centimeters. Bust width of back gives one centimeter behind the curve from the center line in order to reduce the floating phenomenon. So, the amount of center back line dart is one centimeter. Arm hole girth measures as dividing bust girth into four. Also, Goedae width has two methods to measure. First, divide bust girth into ten equal parts and subtract 0.5 centimeters from it. Second, measure neck girth and divide it by four. Sleeve length is equal to Hwajang minus bust width of front. Hand wrist calculates in using bust girth. Make bust girth into quarters and multiply three fifths. Side line measures as deducting from Jeogori length of back to Arm hole girth and multiply two thirds.

• Journal of Radiation Protection and Research
• /
• v.41 no.3
• /
• pp.260-267
• /
• 2016

Background: This study analyzes the differences in the annual averaged atmospheric dispersion factor and ground deposition factor produced using two classification methods of atmospheric stability, which are based on a vertical temperature difference and the standard deviation of horizontal wind direction fluctuation. Materials and Methods: Daedeok and Wolsong nuclear sites were chosen for an assessment, and the meteorological data at 10 m were applied to the evaluation of atmospheric stability. The XOQDOQ software program was used to calculate atmospheric dispersion factors and ground deposition factors. The calculated distances were chosen at 400 m, 800 m, 1,200 m, 1,600 m, 2,400 m, and 3,200 m away from the radioactive material release points. Results and Discussion: All of the atmospheric dispersion factors generated using the atmospheric stability based on the vertical temperature difference were shown to be higher than those from the standard deviation of horizontal wind direction fluctuation. On the other hand, the ground deposition factors were shown to be same regardless of the classification method, as they were based on the graph obtained from empirical data presented in the Nuclear Regulatory Commission's Regulatory Guide 1.111, which is unrelated to the atmospheric stability for the ground level release. Conclusion: These results are based on the meteorological data collected over the course of one year at the specified sites; however, the classification method of atmospheric stability using the vertical temperature difference is expected to be more conservative.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.3
• /
• pp.423-431
• /
• 2011

Warfighting experimentation is an important process for identifying requirements against changing military environment and for verifying proposed measures for reforming military service. The wargame simulation experiment is regarded as one of the most effective means to warfighting experimentation, and its importance is increasing than ever. On the other hand, the results of wargame experiments could be unreliable due to the uncertainty involved in the experimental procedure. To improve the reliability of the experimental results, systematic experimental procedures and analysis methods must be employed, and the design and analysis of experiments technique can be used effectively for this purpose. In this paper, AWAM, a wargame simulator, is used to optimize the organization of operational troops. The simulation model describes a warfighting situation in which the 'survival rate of our force' and the 'survival rate of the enemy force' are considered as responses, 'the numbers of weapons in the squad' as control factors, and 'the uncontrollable variables of the battlefield' as noise factors. In addition, for the purpose of effective experimentation, the product array approach in which the inner and outer orthogonal arrays are crossed is adopted. Then, the signal-to-noise-ratio for each response and the desirabilities for the means and standard deviations of responses are calculated and used to determine a compromise optimal solution. The experimental procedures and analysis methods developed in this paper can provide guidelines for designing and analyzing wargame simulation experiments for similar warfighting situations.

• The KIPS Transactions:PartD
• /
• v.19D no.1
• /
• pp.21-28
• /
• 2012

Predication of protein interaction sites for monomer structures can reduce the search space for protein docking and has been regarded as very significant for predicting unknown functions of proteins from their interacting proteins whose functions are known. In the other hand, the prediction of interaction sites has been limited in crystallizing weakly interacting complexes which are transient and do not form the complexes stable enough for obtaining experimental structures by crystallization or even NMR for the most important protein-protein interactions. This work reports the calculation of 3D surface patches of complex structures and their properties and a machine learning approach to build a predictive model for the 3D surface patches in interaction and non-interaction sites using support vector machine. To overcome classification problems for class imbalanced data, we employed an under-sampling technique. 9 properties of the patches were calculated from amino acid compositions and secondary structure elements. With 10 fold cross validation, the predictive model built from SVM achieved an accuracy of 92.7% for classification of 3D patches in interaction and non-interaction sites from 147 complexes.

• Structural Engineering and Mechanics
• /
• v.19 no.6
• /
• pp.653-677
• /
• 2005

Concrete filled steel tubular columns (CFT) are widely used in civil engineering works, especially in large scale of works because of high strength, deformation, toughness and so on. On the other hand, as a kind of strengthening measure for seriously damaged reinforced concrete piers of viaduct in Hansin-Awaji earthquake of Japan in 1995, reinforced concrete piers were wrapped with steel plate. Then, a new kind of structure appeared, that is, reinforced concrete filled steel tubular column (RCFT). In this paper, compression test and bending-shearing test on RCFT are carried out. The main parameters of experiments are (1) strength of concrete, (2) steel tube with or without rib, (3) width-thickness ratio and (4) arrangement of reinforcing bars. According to the experimental results, the effect of parameters on mechanical characteristics of RCFT is analyzed clearly. At the same time, strength evaluation formula for RCFT column is proposed and tested by experimental results and existed recommendations (AIJ 1997). The strength calculated by the proposal formula is in good agreement with test result. As a result, the proposed evaluation formula can evaluate the strength of RCFT column properly.

• 전자공학회논문지 IE
• /
• v.48 no.1
• /
• pp.51-56
• /
• 2011

In this paper, a variety of digital image processing technique was applied to improve the quality of medical images which is a chest CR image. And the image quality was performed. On the other hand, the high-frequency emphasis filtering and the histogram equalization were realized by MATLAB programs to better the contrast of the chest CR image. As a result of simulation, the sharpness of the original image was elevated by the high-frequency emphasis filtering and the histogram equalization. To evaluate the degree which is improved the image quality by the digital image processing, the subjective evaluation is used by the observation of the image. The sensitivity which is the probability to find a signal or a lesion is calculated. The sensitivity of the image performed the high-frequency emphasis filtering and the histogram equalization became more improved than that of the original and the digital image processing performed in the medical image improved the quality of the image.

• Annals of Clinical Neurophysiology
• /
• v.5 no.2
• /
• pp.187-191
• /
• 2003

Purpose: MEPs elicited by transmagnetic stimulations of the motor cortex are facilitated by voluntary muscle contraction. We evaluated the effects of the imagination of the movements on latencies of MEPs and reciprocal inhibition by using transmagnetic stimulations. Methods: Twenty two healthy volunteers(eight men and fourteen women) were studied. TMSs were delivered at rest and during imagining abducting or adducting right thumb. A stimulator with a round coil and a fixed intensity of 80% of maximum was used to evoke MEPs. MEPs were evoked by magnetic stimulations over the scalp and cervical spine(C7-T1), and central motor conduction times(CMCT) were calculated by subtracting the latency of compound muscle action potentials(CMAPs) obtained by stimulating over the cervical spine from that obtained by stimulating over the scalp. The motor evoked potentials were recorded from right abductor pollicis brevis muscle(APB) and adductor pollicis muscle(AP) simultaneously. Results: Imagination of abduction resulted in a shortened latency of the CMAPs in APB, and a prolonged latency in AP. Imagination of adduction resulted in a shortened latency in AP, and a prolonged latency in APB. But the imagination caused no significant change in the latency of CMAPs elicited by stimulation over cervical spine. Therefore, the changes of the CMCTs account for these latency changes with imagination of movement. With the imagination of abduction, there are significant reduction of the CMCT's in APB(10.8%) and prolongation in AP(5.8%). On the other hand, with the imagination of adduction, prolongation of the CMCT's in APB(7.3%) and reduction in AP(5.9%) were observed. Conclusion: These findings indicate that imagination of muscle contraction increases the excitability of the human corticospinal system. Reciprocal inhibition may be accountable for the prolonged latency in the antagonist muscle.