This paper surveys the extraction condition of polygenetic natural dye, Sappan Wood and the effect of ash to the dyeability and fastness. The appropriate time for extracting Sappon Wood was 1hour. The pH was increased as the amount of ash increase. The pH was nearly invariable according to the time of ash solution, the extracting times and temperature. Absorbance of dyeing fabrics was about 480nm. From the result of K/S value determination of fabrics, 10g/$\ell$ quantity of ash was surfficient for treatment and the amount of Sappon Wood was in 100% o.w.f.. K/S value of fabrics pre-mordanted or post-mordanted were higher than that of fabrics simultaneous mordanted.K/S value was increased as pH of mordanting bath decrease and pre-mordanting and post-mordanting fabrics increased the amount of absorption (K/S value) compared with non-mordanted fabrics. It was found that pH of mordanting bath affected the amount of absorption and color change of dyed fabrics. Light fastness of fabric dyed was very poor and the fastness of fabric dyed was not influenced by the mordanting conditions and methods.
Kim, Younghun;Kim, Chanki;Choi, Sungyeol;Chun, Byungsik
Journal of the Korean GEO-environmental Society
/
v.11
no.11
/
pp.37-45
/
2010
In this study, the value of numerical analysis was compared to the measured value of horizontal displacement during construction. And also, the value was reviewed by comparing with numbers calculated by SUNEX program and EXCAV program. When comparing to suggested values of the maximum horizontal displacement in clayey layer, the displacement caused by the IPS system is larger than one by the Strut girder type system. When comparing the result of SUNEX program to that of EXCAV program, the SUNEX program interprets larger value. It could be concluded the result of SUNEX program is closer to the suggested value, 0.5%H, in clayey layer. The result also shows that the internal friction angle(${\Phi}$) is the key factor of developing horizontal displacement rather than type of supporting systems or materials. That means small horizontal displacement occurs in sandy layer having large value of the internal friction angle, whereas vice versa in clayey layer having small value of the internal friction angle. Therefore, the result of EXCAV program is larger in sandy layer and vice versa in clayey layer. When comparing the measured result during construction to the value of 0.5%H, the measured result is 1.4 times greater than the value of 0.5%H. In contrast, the result of SUNEX program is only 78.1% of the value of 0.5%H and the one of EXCAV program is just 18.1% of that. This result shows the calculated value by SUNEX or EXCAV program is smaller than the observed value by measuring during construction. In result, more careful attention is needed to determine the behavior of the ground. To better analyze the behavior of the ground, more precise finite element method is required.
Journal of the Korean Society of Fisheries and Ocean Technology
/
v.17
no.2
/
pp.77-83
/
1981
Four-day bioassay method was used in this study to find out toxicity levels of DDT and PCP. From this study it was found that M. chrysophekadion was the most sensitive to DDT with a 96 h-TL sub(m) value of 0.0044 mg/l followed by P. Sutchi with a 96 h-TL sub(m) value of 0.0056 mg/l, and the most resistant was C. Siamensis with a 96 h-TL sub(m) value of 0.0133 mg/l. In the case of PCP, it was also found that M. Chrysophekadion and P. Sutchi were the first and second most sensitive to PCP with a 96 h-TL sub(m) value of 0.065mg/l PCP and 0.125mg/l PCP respectively, as in the case of DDT study. T. Nilotica was found to be the most resistant to PCP with a 96 h-TL sub(m) value of 0.264mg/l PCP. The resistant power of fish to pollution varies with the species of fish and the types of pollutants. In order of decreasing sensitivity of fish to DDT based on TL sub(m), the following sequence is obtained M. Chrysophekadion, P. Sutchi, T Nilotica, P. Gonionotus, K. Bicirrhis, L. Bicolor, C. Carpio, R. Heteromorpha, C. Siamensis while in the case of PCP, M. Chrysophekadion, P. sutchi, L. Bicolor, K. Bicirrhis, P. Gonionotus (R. Heteromorpha, R. Trilineata), C. Siamensis, C. Carpio, T. Nilotica.
In order to use leaf mustard Dolsan food preservative ingradient acidity, antimicrobial activity and colors were investigated during pretreatment of leaf mustard Dolsan. pH was remarkably decreased after 8 hours to pretreatment(extracted on shaking) of leaf mustard Dolsan, and no changes were observed after that time. pH of leaf part was higher than stalk after 8 hours storage. Titratable acidity was opposite tendency to the pH. pH was gradually decreased than initial stage during pretreatment of leaf mustard Dolsan at 30, 40 and 5$0^{\circ}C$. After 16 hours pretreatment, the higher pretreatment temperature was, the higher pH was, but after pretreatment for 48 hours, pH of sample pretreated at 5$0^{\circ}C$ was lower than that of sample pretreated at 40 $^{\circ}C$. Antimicrobial activity of leaf mustard Dolsan extract pretreated at 3$0^{\circ}C$ was the strongest of the samples pretreated at 30, 40 and 5$0^{\circ}C$, and that of stalk part was stronger than that of leaf part. L and time. L and b value was higher in the order of samples pretreated at 40, 50 and 3$0^{\circ}C$, and the lower pretreatment temperature was, the higher a value was. L value of stalk part was higher than that of leaf part, but a and b value of leaf part was higher than that of stalk part.
A study has been made of the Korean bentonite aqueous suspension contrast with American bentonite by means of XRD IR swelling, gel formation and rheogram at various conditions such as concentration, temperature and pH. The Korean bentonite was identified as montmorillonite clay containig a small proprotion of crystoballite and mordenite, and its swelling power were acceptable for requirements of Korean pharmacopeia regulations though its values were not satisfied. Korean bentonite swelled to 10 times and American one did to 15 times compared to its bulkiness of powder. The rheogram of Korean bentonite suspension reveals bulged pseudoplatic flow with yield value at higher concentration and pseudoplastic flow without yield value at lower concentration. The higher the concentration, the greater were the apparent viscosity and hysteresis loop. Korean bentonite suspension showed insignificant temperature dependence on both apparent viscosity and hysteresis loop and it was more temperature dependent on viscosity but less on hysteresis loop than those of American sample. The pH dependence was so high on viscosity that apparent minimum value was near pH 7 and maximum value at pH 3 or 7. The hysteresis loop appeared minimum over the pH range 5-7 and maximum near pH 3 or 11. The Korean bentonite was inferior to the American bentonite in swelling volume, gel formation, thioxotropy, however, it would be possible to improve the quality of Korean bentonite by developing the method of purification for bentonite clay.
To understand transition characteristics from wood to charcoal, Quercus variabilis wood was carbonized at 200, 250, 300, 340, 540 and $740^{\circ}C$, respectively. Heating value, pH and surface property by FT-IR spectroscopy of the carbonized charcoal were investigated. Heating value and pH increased with increasing carbonization temperature from 4500 cal/g and 4.3 of the control wood to 8,000 cal/g and 9 of the charcoal carbonized at $740^{\circ}C$, respectively. From FT-IR spectroscopy, the peaks from O-H, C-H and C-O stretching disappeared during carbonization at 540 and $740^{\circ}C$. Aromatic skeletal vibration at near $1,506{\sim}1,593cm^{-1}$ was repidly increased until $540^{\circ}C$. These results suggest that the chemical and physical characteristics of wood components in cell wall can be easily changed by increasing carbonization temperature and the carbonization seem to be incomplete at temperature below $540^{\circ}C$.
Shafigh, Payam;Yousuf, Sumra;Ibrahim, Zainah;Alsubari, Belal;Asadi, Iman
Advances in concrete construction
/
v.11
no.5
/
pp.419-428
/
2021
The pH of cement-based materials (CBMs) is an important factor for their durability, sustainability, and long service life. Currently, the use of supplementary cementitious materials (SCMs) is becoming mandatory due to economic, environmental, and sustainable issues. There is a decreasing trend in pH of CBMs due to incorporation of SCMs. The determination of numerical values of pH is very important for various low and high volume SCMs blended cement mortars for the better understanding of different defects and durability issues during their service life. In addition, the effect of cement hydration and pozzolanic reaction of SCMs on the pH should be determined at initial and later ages. In this study, the effect of low and high-volume fly ash (FA) and ground granulated ballast furnace slag (GGBFS) cement mortars in different curing conditions on their pH values has been determined. Thermal gravimetric analysis (TGA) was carried out to support the findings from pH measurements. In addition, thermal conductivity (k-value) and strength activity indices of these cement mortars were discussed. The results showed that pH values of all blended cement mortars were less than ordinary Portland cement (OPC) mortar in all curing conditions used. There was a decreasing tendency in pH of all mortars with passage of time. In addition, the pH of cement mortars was not only dependent on the quantity of Ca(OH)2. The effect of adding SCMs on the pH value of cement mortar should be monitored and measured for both short and long terms.
본 논문에서는 AF 기능을 구현함에 있어서 2 백만 화소 카메라 모듈인 Sharp LZ0P3731의 기능, AF 모터 (VCM, Voice Coil Motor)에 작용하는 힘과 구동원리, 이를 구동하기 위한 H/W의 설계 특성, 및 DM270을 이용한 AF 제어 시 Focus Value의 특성 분석을 바탕으로 Focus Value 특성을 고려한 최적 AF 알고리즘을 개발하였다. 본 논문에서 제안한 최적 AF 알고리즘은 '최대의 Focus Value가 각 State의 Step Value 마다 각각 다른 위치에서 검출'되는 AF 모터 및 구동 H/W특성을 고려하여, 최적 AF 기능은 최대의 AF Value에 근접하는 Lens Position 제어가 가능하도록 하였다. 이를 검증하기 위한 윈도우용 S/W로 성능을 확인한 결과, 일반적인 AF 기능은 58 프레임으로 3.87초의 시간이 소요되는 반면, 제안한 AF 기능은 25 프레임으로 1.67초로 2배 이상의 빠른 AF 성능을 가졌다.
To study the dyeability(K/S value) and surface color of silk fabrics dyed with Impatiens balsamina extract, its flower, leaf and stem, was extracted by water. This paper investigated some experiments with Impatiens balsamina extract under the various dyeing conditions such as dyeing temperature, dyeing time, repetition of dyeing, dyeing pH with silk fabrics. The results obtained were as follows. 1. It was found that it $\lambdamax$. of silk fabrics dyed with Impatiens balsamina extract was 260nm and its flower, leaf, stem and flowers(white, pink, violet) had same it $\lambdamax$ at 260nm. 2. K/S value was increased when dyeing temperature, repetition of dyeing and time was higher, value of munsell of silk fabrics dyed with Impatiens balsamina extract was yellow-red. dyeing temperature, repetition of dyeing and time was higher, shifted to longer wavelength side. 3. pH added acetic acid was colored reddish yellow-red, but pH added alum was colored yellowish yellow-red in silk fabrics dyed with Impatiens balsamina extract and repetition of dyeing was increased the dye-uptake.
Kim, Wan Keun;Koh, Seong Ung;Kim, Kyoo Young;Yang, Boo Young;Jung, Hwan Kyo
Corrosion Science and Technology
/
v.4
no.6
/
pp.236-241
/
2005
Hydrogen induced cracking (HIC) is one of the hydrogen degradation phenomena of linepipe steels caused by $H_2S$ gas in the crude oil or natural gas. However, NACE TM0284-96 standard HIC test method is hard to satisfy the steel requirements for sour service application since it uses more severe environmental conditions than actual conditions. Therefore, in order to use steels effectively, it is required to evaluate HIC resistance of steels in the practical range of environmental severity. In this study, HIC resistance of two high strength low alloy (HSLA) steels being used as line pipe steels was evaluated in various test solutions with different $H_2S$ pressures and pH values. The results showed that the key parameter affecting crack area ratio (CAR) is $H_2S$ partial pressure of test solution when the pH value of test solution is not over 4. Hydrogen diffusivity was not a constant value, but it was rather affected by the hydrogen ion concentration (pH value) in the solution.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.