• 전기학회논문지
• /
• 제60권10호
• /
• pp.1915-1923
• /
• 2011

For automated guidance control of a magnetically guided-all wheel steered vehicle, it is necessary to have information about position and orientation of the vehicle, and deviations from the reference path in real time. The magnet reference system considered here consists of three magnetic sensors mounted on the vehicle and magnetic markers, which are non-equidistantly buried in the road. This paper presents an observer to estimate such position and orientation at the center of gravity of the vehicle. This algorithm is based on the simple kinematic model of vehicle and uses the data of wheel velocity, steering angle, and the discrete measurements of marker positions. Since this algorithm requires the exact values of initial states, we have also proposed an algorithm of determining the initial position and orientation from the 16 successive magnet pole data, which are given by the magnetic measurement system(MMS). The proposed algorithm is capable of continuing to estimate for the case that the magnetic sensor fail to measure up to three successive magnets. It is shown through experimental data that the proposed algorithm works well within permissible error range.

• 전기학회논문지
• /
• 제63권1호
• /
• pp.132-138
• /
• 2014

The use of AGVs(Automated Guided Vehicles) are increasing in many factories. The most widely used AGV system is that magnetic tapes are attached on the factory floor to make guided path and an AGV equipped with a magnetic sensor follows the path by sensing magnetic flux. In this AGV system, usually a magnetic sensor is attached on the front end of an AGV to detect the guided path and the sensor generates analog voltages proportional to the magnetic flux. The problem is that the AGV in use has rather big tracking errors because the accurate orientation of the AGV can not be detected by using only one magnetic sensor. In this paper, we propose a method to minimize the path tracking errors. In our method, one additional sensor is attached on the rear end of the AGV to estimate the orientation of the AGV and to control more accurately the AGV according to the estimated orientation of the AGV. We performed several experiments and the results successfully show the feasibility of the proposed method.

• 한국항해항만학회지
• /
• 제37권3호
• /
• pp.309-313
• /
• 2013

본 연구는 복합센서를 활용한 무인지게차의 주행 시스템에 대한 것이다. 무인지게차가 화물 이 적재를 위해 랙에 진입할 시 필요한 주행기술로 무인지게차의 위치 및 방향을 정확하게 파악하기 위해 RFID, IMU센서 및 근접센서로 구성된 복합센서 시스템을 이용하였고, 각 센서의 성능실험을 통해 특성을 파악한다. 이를 직접 설계/제작한 실험용 차량에 부착하여 복합센서 시스템을 적용하는 실험을 수행하고 이를 통해 개발된 시스템의 성능을 검증하였다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제17권11호
• /
• pp.3064-3082
• /
• 2023

During the last decade, several Electronic Orientation Aids devices have been proposed to solve the autonomy problems of visually impaired people. When hearing is considered the primary sense for Visually Impaired people (VI) and it is generally loaded with the environment, the use of tactile sense can be considered a solution to transmit directional information. This paper presents a new wearable haptic system based on four motors implemented in shoes, while six directions can be played. This study aims to introduce an interface design and investigate an appropriate means of spatial information delivery through haptic sense. The first experiment of the proposed system was performed with 15 users in an indoor environment. The results showed that the users were able to recognize, with high accuracy, the directions displayed on their feet. The second experiment was conducted in an outdoor environment with five blindfolded users who were guided along 120 meters. The users, guided only by the haptic system, successfully reached their destinations. The potential of tactile-foot stimulation to help VI understand Electronic Orientation Aids (EOA) instructions was discussed, and future challenges were defined.

• Asian Pacific Journal of Cancer Prevention
• /
• 제15권7호
• /
• pp.3179-3183
• /
• 2014

Background: The purpose of study was to evaluate radiologic or clinical features of breast cancer undergoing ultrasound (US)-guided 14G core needle biopsy (CNB) and analyze the differences between underestimated and accurately diagnosed groups. Materials and Methods: Of 1,898 cases of US-guided 14G CNB in our institute, 233 cases were proven to be cancer by surgical pathology. The pathologic results from CNB were invasive ductal carcinoma (IDC) (n=157), ductal carcinoma in situ (DCIS) (n=40), high-risk lesions in 22 cases, and benign in 14 cases. Among high-risk lesions, 7 cases of atypical ductal hyperplasia (ADH) were reported as cancer and 11 cases of DCIS were proven IDC in surgical pathology. Some 29 DCIS cases and 157 cases of IDC were correctly diagnosed with CNB. The clinical and imaging features between underestimated and accurately diagnosed breast cancers were compared. Results: Of 233 cancer cases, underestimation occurred in 18 lesions (7.7%). Among underestimated cancers, CNB proven ADH (n=2) and DCIS (n=11) were diagnosed as IDC and CNB proven ADH (n=5) were diagnosed at DCIS finally. Among the 186 accurately diagnosed group, the CNB results were IDC (n=157) and DCIS (n=29). Comparison of underestimated and accurately diagnosed groups for BI-RADS category, margin of mass on mammography and US and orientation of lesion on US revealed statistically significant differences. Conclusions: Underestimation of US-guided 14G CNB occurred in 7.7% of breast cancers. Between underestimated and correctly diagnosed groups, BI-RADS category, margin of the mass on mammography and margin and orientation of the lesions on US were different.

• 한국항행학회논문지
• /
• 제25권4호
• /
• pp.293-298
• /
• 2021

일반적으로 유도무기의 탐색기와 유도조종장치는 유도탄의 상태를 나타내기 위해 표적, 탐색, 인지, 포착정보를 처리하여 유도무기의 운용 및 제어를 담당하는 역할을 한다. 유도에 필요한 신호는 시선 변화율 신호, 시각 신호, 종말 단계 동체 지향 신호이며, 발사 통제에 필요한 신호는 표적, 감지 신호가 필요하다. 최근 유도탄의 복잡하고 처리하기 어려운 유도탄 신호를 실시간으로 처리하기 위해 유도탄의 데이터 처리 속도를 높여야 한다. 본 연구는 PLINQ(Parallel Language-Integrated Query)의 병렬 알고리즘 방법 중 스톱앤고와 역 열거형 알고리즘을 적용한 후 유도탄 점검 프로그램을 이용하여 실시간으로 유도탄 필요 신호 데이터 처리속도를 비교 후 처리결과를 나타내었다. 도출된 데이터 처리결과 기준으로 다중코어 처리방식과 단독코어 처리방식 CPU(Central Processing Unit) 처리속도 비교, CPU 코어 이용률을 비교하고 병렬처리 알고리즘 적용 시 유도탄 데이터 처리에 효과적 방법을 제안한다.

• 한국소음진동공학회논문집
• /
• 제15권1호
• /
• pp.81-86
• /
• 2005

In this work, we propose a new ultrasonic damage inspection method in plate structures. The proposed method employs an OPMT(orientation-adjustable patch-type magnetostrictive transducer) in order to make the ultrasonic waves directed to a specific target point. For experiments, virtual grid points were set up at every 50 mm in an aluminum plate and two OPMTs were used for inspection. If there exists a crack in a plate, the reflected Lamb wave from the crack is measured in addition to the direct waves from the transmitting transducer to the receiving transducer.

• 대한의용생체공학회:의공학회지
• /
• 제26권5호
• /
• pp.265-270
• /
• 2005

A new Computer Integrated Surgical Robot system is composed of a surgical robot, a surgical planning system, and an optical tracking system. The system plays roles of an assisting surgeon and taking the place of surgeons for inserting a pedicle screw in spinal fusion. Compared to pure surgical navigation systems as well as conventional methods for spinal fusion, it is able to achieve better accuracy through compensating for the portending movement of the surgical target area. Furthermore, the robot can position and guide needles, drills, and other surgical instruments or conducts drilling/screwing directly. Preoperatively, the desired entry point, orientation, and depth of surgical tools for pedicle screw insertion are determined by the surgical planning system based on CT/MR images. Intra-operatively, position information on surgical instruments and targeted surgical areas is obtained from the navigation system. Two exemplary experiments employing the developed image-guided surgical robot system are conducted.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2000년도 추계학술대회논문집
• /
• pp.219-225
• /
• 2000

The major movement block of the containers have range between apron and designation points on yard in container terminal. The yard tractor operated by human takes charge of its movement in conventional container terminal. In automated container terminal, AGV(Automated Guided Vehicle) has charge of the yard tractor's role and the navigation path is ordered from upper level control system. The automated container terminal facilities must have the docking system to guide landing line to have high speed travelling and precision positioning. The general method for docking system uses the vision system with CCD camera, infra red, and laser. This paper describes the detection of AGV's position and orientation using laser slit beam to develop docking system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.807-808
• /
• 2008

This is concerned with the radiation pattern of elastic waves in a plate generated by an orientation-adjustable patch-type magnetostrictive transducer. In general, not only the Lamb waves but also shear horizontal (SH) waves are produced by the deformation of the circular magnetostrictive patch bonded to a plate. Among the two types of waves, this paper investigates the radiation patterns of SH waves. A number of experimental results are presented. They are also accurately predicted by a theory developed by the present authors. Experimental findings were explained by a theoretical analysis.