• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.5
• /
• pp.121-129
• /
• 2006

This study look into the mechanisms of growth and magnification of the cracks and delamination in the pre-cracked RC beams repaired with carbon fiber sheets. The experimental parameters were loading type, loading speed and crack. In the experiments, it was confirmed that a failure of beams began with development and propagation of the stepped delamination in the below the loading point due to the rapid change of shear force, but mechanisms of the failure were not influenced with loading type, loading speed and pre-cracks. Particularly, in the case of beams having the pre-cracks, growth of crack concentrated at the special crack below the loading point and led to failure of the beam by delamination due to magnification of crack.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.7 no.1
• /
• pp.10-15
• /
• 2002

Environmental and medium factors were investigated as basic data for optimizing DHA production when using Thraustochytrium aureum. To study the effect of environmental conditions, the rotation speed and culture temperature were changed. Plus the trend of the growth characteristics, lipid content in the biomass, and DHA content in lipids were evaluated according to various initial glucose concentrations. The biomass, lipid, and DHA analyses showed that the physiological characteristics of T. aureum were closely related with the environmental and medium conditions, as in the case of other marine microorganisms. For example, a low rotation speed of 50 rpm lowered the cell growth rate as well as the DHA content in the lipids. A low temperature had a negative effect on the cell growth, yet a positive effect on the lipid content in the biomass. Different initial glucose concentrations had no effect on the lipid content in the biomass or DHA content in the lipids, yet did affect the cell growth. Accordingly, these results show that environmental and medium factors must be synthetically considered in order to optimize DHA production when using T. aureum.

• Microbiology and Biotechnology Letters
• /
• v.33 no.1
• /
• pp.51-55
• /
• 2005

The effect of rotation speed and culture temperature on the growth of T. aureum and also the biosynthesis of lipid and DHA was investigated. The optimal temperature for the growth was $32^{\circ}C$, but the best temperature for the maximum production of lipid and DHA was $18^{\circ}C$ in the range of $4^{\circ}C\;to\;39^{\circ}C$. In the case that the temperature was higher than $39^{\circ}C$ and lower than $11^{\circ}C$, the growth was very slow and the production of DHA was also very low. However, the lipid content in the biomass became higher with decrease in the culture temperature. The rotation speed for the maximum growth was 100rpm. But the growth and the production of DHA were not affected by the change of rotation speed in the range of 100 to 250 rpm. When the rotation speed was 50 rpm, the growth as well as the production of DHA and lipid was greatly reduced.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2001.04a
• /
• pp.73-76
• /
• 2001

We have simulated the effect of fracture characteristics on reduction of effective permeability of the fractured rocks due to in-situ bacteria growth. A nutrient is injected continuously for growth of in-situ bacteria. We used a power law for fracture length distribution and a fBm for fracture aperture spatial distribution. The results show that in-situ bacteria growth reduces the Permeability hyperbolically, but the porosity of backbone fracture does not change significantly. It shows that reduction of the permeability proceeds at faster speed for smaller value of length exponent(a) and for larger value of Hurst exponent(H). The fracture length distribution has stronger effect on speed of reduction than the aperture spatial distribution. The time needed to reduce permeability is inversely proportional to the hydraulic gradient.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.2 no.1
• /
• pp.43-50
• /
• 1992

$ LiNbO_3$ single crystals were grown using the Czochralski Method at various pulling speeds. Macroscopic defects such as cracks, bubbles and cellular structures were observed in some crystals. Cracks and bubbles observed in the crystals depended on the pulling speed and cooling rate. $ LiNbO_3$ crystals of about 15mm diameter could be grown properly at 6-7mm/h pulling speed and $ 20^{circ}C/h$ cooling rate. In order to investigate dielectric properties and optical properties for device application, these properties were measured for the sample cut along a axis and c axis at different temperatures.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1010-1015
• /
• 2003

Bubble growth on microheater has been experimentally investigated in this study. The experiment was performed using platinum microheaters having dimensions of 300 ${\mu}m$ or 50 ${\mu}m$ in length, 20 ${\mu}m$ or 5 ${\mu}m$ in width, and $0.2{\pm}0.01$ ${\mu}m$ in thickness. A high speed video camera was used to observe bubble growth at 2,000 frames per second. Microheater temperature was measured at the rate of 300 Hz. with a data acquisition system. Bubble nucleation frequency increased with working fluid temperature. Although the slope of temperature drop was similar in all cases, the magnitude of temperature drop was different. The temperature profiles and the high speed camera images were combined to explain temperature drop.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.5
• /
• pp.211-217
• /
• 2001

Czochralski법에 의한 ZnWO₄단결정을 [100], [101], [001] 방향으로 성공적으로 성장시켰다. 각 축 방향에 따른 성장조건이 rotation speed, pulling rate, 성장된 결정의 직경 등의 변수를 가지고 조사되어졌다. 성장된 결정의 냉각시 발생되는 균열을 annealing 효과에 의하여 방지할 수 있었다. 성장된 결정의 방위는 Laue back reflection으로 결정하였다. 각 축 방향으로 성장된 결정의 미세구조적 특징이 논하여졌으며, 경도, 열팽창계수 및 유전상수의 물리적 특성이 평가되어졌다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.84-87
• /
• 2001

The high speed machining which cam improve the production and quality has been remarkable in die/mold industry with the growth of parts and materials industries. The speed of machine tool increases, but on the other hand, the response of sensors I not being improved. Therefore, the condition monitoring techniques for the machine too, tool and workpiece in high speed machining are incomplete. In this study, characteristics of the tool edge roughness were verified from the high frequency components of cutting force signals acquired by the high speed dynamometer. Also, the experimental evaluation technique for the machinability and condition monitoring in high speed machining was established by analyzing the cutting force, acceleration and surface roughness.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.3
• /
• pp.13-19
• /
• 2003

The high speed machining technology has been improved remarkably in die/mold industry with the growth of parts and materials industries. Though the spindle speed of machine tool increases, the condition monitoring techniques of the machine tool, tool and workpiece in high speed machining ate incomplete. In tins study, efficient sensing technology in high speed machining is suggested by observing the characteristics of cutting force, gap sensor and accelerometer signal also, machinability of high-speed machining is experimentally evaluated sensing technique to monitor the machine tool and machining conditions was performed.

• Journal of Bio-Environment Control
• /
• v.5 no.2
• /
• pp.152-159
• /
• 1996

Experiment was performed in a newly developed wind tunnel with light system to determine the aerodynamic resistance and eddy diffusivity above the plug stand under artificial light. Maximum air temperature appeared near the top of the plug stand under artificial light. Since Richardson number was ranged from -0.07 to +0.01, the atmosphere above the plug stand in wind tunnel was in an unstable or near- neutral stability state. The average aerodynamic resistance at rear region of plug stand was 25 % higher than that at middle region. Eddy diffusivity($K_{M}$) linearly increased with the increasing air current speed. $K_{M}$ at air current speed of 0.9 m.$s^{-1}$ was about two times as many as that at air current speed of 0.3 m.$s^{-1}$. And average $K_{M}$ at the rear region was 15% lower than that at the middle region. These results indicated that the diffusion of heat and mass along the direction of air current inside the plug stand was different. It might cause the lack of uniformity in the growth and quality of plug seedlings. The wind tunnel developed in this study would be useful to investigate the effects of air current speed on microclimates and the growth of plug seedlings under artificial light in a semi- closed ecosystem.