• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권8호
• /
• pp.387-393
• /
• 2001

This paper describes an advanced measuring method and precise evaluation of the ground resistance for the grounding system of energized substations and power equipments. A grounding system of substations consists of all interconnected grounding connections of grounded conductors, neutral ground wires, underground conductors of distribution lines, cable shields, grounding terminals of equipments, and etc. It is very difficult to measure the accurate ground resistance of the grounding terminals of equipments, and etc. It is very difficult to measure the accurate ground resistance of the grounding system of high voltage energized substations because of harmonic components caused by switched power supplies or overloads. The conventional fall-of-potential method may be subject to big error if stray ground currents and potentials are present. In this work, to improve the precision in measurements of the ground resistance by eliminating the effects of harmonic components and stray currents and potentials, the investigations of the ground resistance measurement by using a low pass filter in a model energized grounding system were conducted. The accuracy of ground resistance mesurements was evaluated as a function of the ratio of the test signal to noise (S/N). The errors due to the proposed ground resistance measurement method were decreased with increasing S/N and were less than 5[%] as S/N is 10. The proposed ground resistance measurement method appears to be considerably more accurate than the conventional fall-of -potential method. It is allows cancellation of the parasitic resistance of energized grounding systems, to employ the measurement method that allows cancellation of the parasitic effects due to other circulating ground currents and ground potential rises in practical situations.

• 조명전기설비학회논문지
• /
• 제25권5호
• /
• pp.92-97
• /
• 2011

This paper deals with the improvement of electrode installation for measurement of ground resistance through investigation on the spot in buildings. The investigation was carried out for an earthing terminal board for measurement of ground resistance, installation of auxiliary electrode, etc. The criteria value is set up by measuring method of ground resistance in international standard. In case of inadequate installation of auxiliary electrode, a relative error is analyzed and adequate installation method of auxiliary electrode is proposed. As a consequence, it is necessary to write direction of ground and equipment, and separate auxiliary electrode for measurement of ground resistance in order to minimize measuring error.

• 전기학회논문지P
• /
• 제56권2호
• /
• pp.109-114
• /
• 2007

This paper summarize about the auxiliary electrode measured a ground resistance. The method to measure a ground resistance is the fall-of-potential method to using an auxiliary electrode. And an auxiliary electrode must be set up on the ground. Today it is so difficult to set up the auxiliary electrode on the ground because of many concrete building and many paved roads. So this paper is regarding a trust analysis of the ground resistance measurement by the substitute auxiliary electrode. It substituted a iron structure around the building, a neutral line multiplex ground to earth, a wire net for auxiliary electrode. This information is confirmed bv compared with the measurement value.

• 조명전기설비학회논문지
• /
• 제16권4호
• /
• pp.117-123
• /
• 2002

접지저항의 측정은 접지계통의 접지성능이 적정한가를 평가하기 위한 가장 기본적이고 중요한 작업이라고 할 수 있다. 그러나 실제 현장에서, 특히 접지극의 크기가 큰 경우일수록 접지저항을 정확히 측정하기란 쉽지 않은데, 이는 정확한 접지전위 측정을 위한 기준전위 점을 찾기가 힘들기 때문이다. 본 논문에서는 접지극 주변에서 측정한 지표면전위를 분석하여 기준전위 점의 위치를 정확히 식별하는 방법과 그 정당성을 제시하였다.

• 한국전기전자재료학회논문지
• /
• 제23권1호
• /
• pp.61-64
• /
• 2010

Footing Resistance of a 154 kV transmission towers in korea is commonly required to be less than 15 ohm to avoid lightning back-flashover accident. The periodic measurement of Footing Resistance is important to verify that the grounding performance of the towers has been maintained good. Towers are electrically connected in parallel with overhead grounding wire, therefore footing resistance of each tower will be measured after disconnecting the overhead ground wires from the towers. however, In this paper, three direct measurement methods of footing resistance are presented. There are very useful methods without disconnecting overhead ground wires from the tower under measurement. They are compared in KEPCO 154 kV transmission towers. The experimental results describe performances of them.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기설비전문위원
• /
• pp.85-87
• /
• 2007

This paper summarize about the auxiliary electrode measured a ground resistance The method to measure a ground resistance is the fall-of-potential method to using an auxiliary electrode. And an auxiliary electrode must be set up on the ground. Today it is so difficult to set up the auxiliary electrode on the ground because of many concrete building and many paved roads. So this paper is regarding of the ground resistance measurement by the substitute auxiliary electrode. It substituted a iron structure around the building, a wire net for auxiliary electrode. This information is confirmed by compared with the measurement value.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2000년도 학술대회논문집
• /
• pp.77-81
• /
• 2000

The purpose of this paper is to describe a new measuring method of ground resistance for the grounding system in energized power equipment and substations. It is very difficult to measure the accurate ground resistance in energized power equipment and substations because of the noise conducted from all external connections to the grounding system and harmonics components caused by unbalanced loads and overloads. The ground resistance that is measured with existing methods includes not only the effect of desired signals but also noise components for the measurement period in grounding system. The measured value of ground resistance can entirely be different from actual value. In this paper, to eliminate 60[Hz] power system interference and harmonic components the low-pass filter method was used in the measurement of ground resistance.

• 한국인터넷방송통신학회논문지
• /
• 제19권6호
• /
• pp.65-71
• /
• 2019

기존의 대지저항률과 접지저항 현장 측정 방식은 일정한 간격의 측정전극을 설치하여 전류를 인가하여 대지의 저항값에 따른 전압강하를 측정하게 되는데 현장 대지의 층상 구조가 특이성을 갖게 되면 역산 시 경계 조건의 오차를 발생하게 되고 접지 설계 시 중요한 대지저항률 분석이 시뮬레이션 상과 많은 차이를 보이게 된다. 본 연구는 정보통신 융합환경에서 아두이노 모듈과 스마트 접지 측정 기술를 활용하여 대지의 층상이 특이성을 갖는 구조라도 신뢰할 수 있는 스마트 대지 저항 측정장치를 개발하여 대지저항을 분석하고 데이터를 축적하여 대지의 경년변화를 예측한다. 현장의 지형적인 특성을 고려하여 접지저항과 대지저항 측정 시 각도와 거리를 정확하게 위치시켜 보조전극을 설치할 수 있는 접지저항 측정장치 및 측정방법을 제안한다. 정확한 접지저항 값을 선정할 수 있게 하기 위해 설치된 전극을 통해 접지저항 값뿐만 아니라, 대지저항률을 취득할 수 있어 유사지역에 전기시설물 설치 시에 유용한 자료로 활용할 수 있다. 또한 신뢰성 높은 데이터를 활용하고 현장의 대지구조를 분석하여 공사비용 뿐 아니라 접지설계에서 중요한 비중을 차지하는 대지에 대한 정밀한 분석으로 전위상승 등의 접지설비설계에서 많은 활용이 기대된다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 춘계학술대회 논문집
• /
• pp.352-355
• /
• 2009

The ground resistance has been used as a method of estimating the capability of counterpoise. When transient currents blow through a ground electrode, it is reasonable to evaluate the performance of ground electrode system as a ground impedance instead of ground resistance. However, the measurement method of ground impedance for counterpoise is not clearly presented. This paper describes the measurement method of ground impedance considering the earth mutual resistances and AC mutual coupling. When we measure the ground impedance, the error due to earth mutual resistances depends on the distance between the auxiliary electrodes and the electrode under test. The measurement accuracy of high frequency ground impedance is mainly influenced by the location of the current electrode and the potential electrode.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권4호
• /
• pp.234-237
• /
• 2004

Measuring ground resistance has been a popular method of evaluation of the grounding electrode performance. If some portions of grounding electrodes are lost by corrosion, aging or other reasons, consequent deteriotation of the grounding performance would be resulted. It is one of the reasons why it is required to evaluate the performance of grounding systems regularly. However, in case of the electric facilities with multi-grounded system such as power substations with multi-grounded overhead ground wires and/or distribution line neutrals, it is practically difficult to disconnect neutrals or skywires from the substation grounding mesh for the ground resistance measurement. In this paper, a method for the grounding performance measurement of multi-grounded systems, which is based on the measuring ground current distributions, has been proposed. A field test results has shown the validity of the proposed test method.