• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.374-378
• /
• 2003

From linear motor feed system model, two axis control rules have been applied. As an application process, a flexible disk grinding system process has been also introduced that utilized varying disk orientation with respect to workpiece along with the applied feed speed. A known process model methodologies has been used to fomulate processed surface profiles. Various process conditions including cutting speed, maximum feed speed and orientation angles could applied to observe process results sensitivities. Even though continuous and constant feed speed has been applied to the process, the results from the trapezoidal input velocity profiles would be observed and compared.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.193-200
• /
• 2006

To perform the finish grinding process of ferrules which are widely used as fiber optic connectors, a high-precision centerless grinding machine is necessary. The high-precision centerless grinding machine is consisted of the hydrostatic GW and RW spindle systems, hydrostatic RW feeding mechanism, RW swivel mechanism, on-machine GW and RW dressers, and concrete-filled steel bed. In this study, the thermal characteristics of the high-precision centerless grinding machine such as the temperature distribution, temperature rise and thermal deformation, are estimated based on the virtual prototype of the grinding machine and the heat generation rates of heat sources related to the machine operation conditions. The reliability of the predicted results is demonstrated by the temperature characteristics measured from the physical prototype. Especially, the predicted and measured results show the fact that the high-precision centerless grinding machine has very stable thermal characteristics.

• 대한기계학회논문집A
• /
• 제29권4호
• /
• pp.614-623
• /
• 2005

This study aims to perform the characteristic evaluation of surface grinding for the STD11 material with experimental and analytic techniques based on the response surface model. The grinding force acting on the workpiece and the ground surface roughness were measured according to the change of grain size, table speed and depth of cut. The effect of spark-out on the grinding force and the surface roughness was also characterized. The frictional coefficient between workpiece and grinding wheel could be determined by the analysis of spark-out effect. From the experimental data, the second-order response surface models were developed to predict the grinding force and the surface roughness. Validation of the developed model was examined.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1109-1112
• /
• 2001

In the grinding process, the edge of shape is very important to evaluate the surface roughness and the precision of dimension. To keep precision of product, parameters with respect to the amount of wheel wear have to limit by grinding condition. In this paper, we measured variation of grinding force to seek the grinding characteristics by the amount of wheel wear in surface grinding. Also, we find out that how these condition give influence to wheel life.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.8-13
• /
• 1997

In order to utilize the information of well-known grinding data or grinding machine, a database needs to be designed by considering the delicate property of the machine tools for the high precision and quality of the demanding specification. Among the machine tools, machining conditions of the grinding are various and knowledge repeatance obtained form the grinding process are less credable.Therefore it is desirable for D/B, which is used to set the grinding conditions, to utilize the maximum machine tool capability. The present paper studied occurance limit of chatter vibration and burn considering the characteristics of machine tool. And also basic experiments were performed to establish optimum grinding canditions which can maximize the machining efficiency.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.19-24
• /
• 1998

This paper aims to clarify the effects of grinding conditions on the ground surface and bending strength in surface grinding of various ferrites with diamond wheel. The main conclusions obtained were as follows. The surface roughness becomes better at lower wheel speed in the case of v/V=1$\times$10-3, and the condition of v/V=1$\times$10-4shows the best performance for the finish grinding. When the relative contact temperature becomes lower at a constant value of v/V, the ground surface exhibits lower roughness. The ground surface shows that the fracture process during grinding becomes more brittle at the higher value of v/V. The damage depth which affect the bending strength is below 10$\mu$m in the grinding condition of S=10㎣/mm.s with the diamond tool after dressing & truing, however, the depth increases with increasing removal rate(S). When the strength degradation due to grinding is larger, the removal depth for the recovery of strength requires a larger size.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.35-39
• /
• 2001

The precision grinding process is carried out with fine-cutting operation after coarse-cutting operation. So, the laminated grinding wheel has been developed to reduce the ineffectiveness induced by changing the operations. In this study, to investigate the possibility of the practical use of the laminated grinding wheel, the surface residual stress of the workpiece ground by the laminated grinding wheels was compared with that ground by the general grinding wheel, and the influence of the difference in grain sizes, between the coarse grit and fine grit of the laminated grinding wheel, on the surface roughness of the workpiece was investigated.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.172-179
• /
• 2005

A high-precision centerless grinding machine has been recognized as a core equipment performing the finish outer-diameter grinding process of ferrules which are widely used as fiber optic connectors. In this study, in order to realize the high-precision centerless grinding machine, the structural characteristic analysis and evaluation are carried out on the virtual prototype consisted of the steel bed, hydrostatic GW and RW spindle systems, hydrostatic RW feed mechanism, RW swivel mechanism, and on-machine GW and RW dressers. The loop stiffnesses of centerless grinding machine are estimated based on the relative deformations between GW and RW caused by the grinding forces. And the simulated results illustrate that the concrete-filled bed has the considerable effect on the improvement of the structural stiffness of centerless grinding machine.

• 한국생산제조학회지
• /
• 제8권5호
• /
• pp.20-24
• /
• 1999

Grinding System is very difficult to examine closely wear phenomenon or dynamic characterastic because it is very complex and different from a general cutting system, Considering automatization and precision it is very important to examine closely grinding system. In this study grinding wheel surface is acquired by using computer vision system in order to explain wear and loading phenomenon. We investigate the relationship between wear and Fourier spectrum of acquired image and observe the entropy variation in the process of manufacturing.

• 한국기계가공학회지
• /
• 제12권4호
• /
• pp.75-80
• /
• 2013

Single crystal sapphire being used in high technology industry is a brittle material with a high hardness and excellent physical properties. ELID(Electrolytic In-Process Dressing) grinding technology was applied to material removal machining process of single crystal sapphire wafer. Ultrasonic vibration which added to material using ultrasonic table was adopted to efficient ELID grinding of sapphire materials. The evaluation of the ground surface of single crystal sapphire wafer was carried out by means of surface measuring by using AFM(Atomic Force Microscope), surface roughness tester and optical microscope device. As the results of experiment, it was shown that more efficient grinding was conducted when using ultrasonic table. In case of using #170 grinding wheel, surface roughness of ELID ground specimen in using ultrasonic table was superior to ELID ground specimen without ultrasonic table. However, In case of using #2000 grinding wheel, surface roughness of ELID ground specimen in using ultrasonic table was inferior to ELID ground specimen without ultrasonic table.