• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.368-374
• /
• 2007

CVD-SiC coating has been introduced as a protective layer in TRISO nuclear fuel particle of high temperature gas cooled reactor (HTGR) due to its excellent mechanical stability at high temperature. In order to prevent the failure of the TRISO particles, it is important to evaluate the fracture strength of the SiC coating layer. It is needed to develop a new simple characterization technique to evaluate the mechanical properties of the coating layer as a pre-irradiation step. In present work, direct strength measurement method with the specimen of hem i-spherical shell configuration was suggested. The indentation experiment on a hemisphere shell with a plate indenter was conducted. The fracture strength of the coating layer is related with the critical load for radial cracking of the shell. The finite element analysis was used to drive the semi-empirical equation for the strength measurement. The SiC hemispherical shells were successfully recovered from the section-grinding of TRISO coated particle and successive heat treatment in air. The strength of CVD-SiC coating layer was evaluated from the experimentally measured critical load during the indentation on SiC hemisphere shell. Weibull diagram of fracture strength was also constructed. This study suggested a new strength equation and experimental method to measure the fracture strength of CVD-SiC coating of TRISO coated fuel particles.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.99-102
• /
• 1999

In the study, the effect of the replacement content(20, 40, 60, 80%) and particle fineness and the chemical activator of the fly-ash on the flow and strength development of mortar was investigated. We found that the higher raito of the fly-ash replacement produced the lower the mortar strength and the higher fineness of the fly-ash yielded the higher strength. Also, we used Na2SO4 as activator of fly-ash to rise compressive strength mortar. The result as follows: the fly-ash mortar which stimulated by chemical activator, was higher strength development at early than the fly-ash mortar without chemical activator. But in the late age, the result indicated adversely.

• Journal of the Korean Wood Science and Technology
• /
• 제44권2호
• /
• pp.166-171
• /
• 2016

Size reduction is one of the major pre-processing operations in using biomass as a source of energy or raw materials for forest products industry. The grinding characteristics of dried yellow poplar wood chips were investigated using laboratory knife mill with three different screen aperture diameters to provide the basic information for the optimizing of size reduction processes in biomass industry. Average specific energy consumptions were 0.157, 0.137, and 0.093 Wh/g for the screen aperture diameters of 5.0, 7.5, and 9.0 mm, respectively. According to the results of size distribution analysis of ground particles, the sizes of the most of ground particles were much smaller than the aperture diameters of the screens installed on knife mill used in this study.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2016년도 추계 학술논문 발표대회
• /
• pp.98-99
• /
• 2016

Oyster shell is light weighted and its strength characteristic is similar to sand so we have reviewed to find its suitability of aggregate. Therefore we found fineness modulus and size distribution of oyster shell by grinding it with inverter cutter mill varying inverter speed and screening size. In our test, the fineness modulus has tendency of decrease in higher speed and tendency of increase in bigger diameter of screening size. 5~2.5mm, 2.5~1.2mm, 1.2~0.6mm, and below 0.6mm of oyster shell particle size could be used in further test for suitability of aggregate.

• 한국식품영양과학회지
• /
• 제39권6호
• /
• pp.837-842
• /
• 2010

우리밀 semolina의 면류가공 산업현장에 적용될 수 있는 방안을 모색하고자 제분과정 중 발생하는 coarse semolina (CS), medium semolina(MS), fine semolina(FS)의 이화학적 특성을 비교 분석하였다. 실험에 사용한 semolina 모두가 FS를 제외하고는 $250{\mu}m$ 이상의 큰 입자가 약 75% 이상을 차지하였고, MS의 경우 durum semolina(DS)와 가장 유사한 입도분포를 나타내었다. 조단백, 조회분은 DS가 유의적으로 높게 나타났고, 우리밀 semolina는 CS, MS, FS 순으로 감소하였다. 조지방은 DS가 가장 낮게 나타났고, CS, MS, FS는 유의적 차이를 나타내지 않았다. L값은 작은 입도분포를 많이 가질수록 높게 나타났고, 손상전분은 DS와 FS에서 낮게 나타났으며, CS에서 가장 높은 손상전분을 나타내었다. 아밀로오스 함량 또한 비교적 작은 입도분포를 가지는 DS와 FS에서 각각 29.80%과 29.08%로 높게 나타났으며, 물결합력은 DS가 가장 높았고, 우리밀 semolina의 경우 FS에서 높게 나타났다. 용해도와 팽윤력에서도 낮은 손상전분과 작은 입도분포를 가지는 FS에서 높게 나타났다. 미세구조 관찰시 FS와 MS에서 가루로부터 깨끗하고 뚜렷한 작은 전분입자가 파열되지 않고 전분 입자형태를 유지하면서 가루 표면에서 떨어져 나와 있는 전분립들을 관찰할 수 있었다. 이러한 결과로부터 제분에 의한 semolina의 이화학적 특성변화가 많이 일어남을 알 수 있으며, 부가적인 제면특성 검사를 통해 FS의 면류가공 적용이 가능하리라 생각된다.

• 유기물자원화
• /
• 제11권3호
• /
• pp.60-66
• /
• 2003

본 연구는 혐기성 소화를 이용한 음식물쓰레기와 하수슬러지 병합처리를 위한 음식물쓰레기 전처리 공정 방안을 모색하기 위하여 수행되었다. 음식물쓰레기 전처리 공정에 따른 음식물쓰레기 단위 공정별 성상 변화와 산발효조 적정 투여 기초조사 및 음식물쓰레기와 하수슬러지 혼합비 특성변화를 통한 산발효조의 효율 향상방안을 검토하였다. 연구결과, 음식물쓰레기의 구성성분은 대부분이 곡류와 채소류로 산발효 공정에서 유기산으로 전환될 가능성이 충분한 것으로 판단되며, 산발효조 투입시 TS의 적정한 범위를 위한 음식물쓰레기와 희석수의 비율은 1:5가 적합한 것으로 나타났다. 음식물쓰레기 분쇄 후 입도 분포 특성을 고려할 때 약 8mm 이하의 입자가 적합하며, 음식물쓰레기와 하수슬러지 슬러지의 혼합비는 3:7 이하가 적합한 것으로 나타났다.

• 한국대기환경학회지
• /
• 제9권3호
• /
• pp.191-199
• /
• 1993

This paper describes the results of a systematic study to determine the characteristics of particle generated from various types of asbestos containing material(ACM) and manmade fiber material(MMFM) during operations of cutting and grinding in laboratory and workplace. Tests were conducted with a specially designed glove box which allowed complete sampling of the generated asbestos fibers. Specificially, air measurements were made during ACM and MMFM installation in building. All personal air samples collected were identified by polarized light microscopy(PLM), X-ray diffraction(XRD) and scanning electron microscope with energy dispersive X-ray analysis(SEM/EDXA). Also, the samples were counted by phase contrast microscope(PCM) in order to compare the results with the permissible exposure standard for workplace. Results indicate that the characterisitcs of fibers found in the roofing sheet, the ceiling and the wall insulation boards were identical to those of asbestos, while the characteristics of fibers found in the ceiling insulation board, the floor tile and the sprayed on insulation products in parking area were identical to those of asbestos, while the characteristics of fibers found in the ceiling insulation board, the floor tile and the sprayed on insulation products in parking area were identical to those of rock wool. The concentrations of airborne fibers from various building materials cut by a grinder for 5 minutes were in the ranges of 0.09 $\sim$ 1.71 fibers/cc(f/cc). The highest concentration(1.71f/cc) was found during grinding the wall insulation board which also contains rock wool. The airborne fiber concentrations generated by installing at workplace were ranged from 0.0009 to 0.029 f/cc. All asbestos fibers from the ceiling insulation board at workplace were less than 20$\mu$m in length and more than 20% of them had the average aspect ratio greater than 20. Therefore, for the purpose of decreasing asbestos and man-made fiber concentrations at the workplace, the ceiling and wall board should use strong binding material to increase the binding force with fiber. Also, the permissible exposure standard for workplace(2.0f/cc) in Korea should be constituted below the maximum avaiable concentration measured at glove box.

• The Journal of Advanced Prosthodontics
• /
• 제3권4호
• /
• pp.221-228
• /
• 2011

PURPOSE. Veneering porcelain might be delaminated from underlying zirconia-based ceramics. The aim of this study was the evaluation of the effect of different surface treatments and type of zirconia (white or colored) on shear bond strength (SBS) of zirconia core and its veneering porcelain. MATERIALS AND METHODS. Eighty zirconia disks (40 white and 40 colored; 10 mm in diameter and 4 mm thick) were treated with three different mechanical surface conditioning methods (Sandblasting with $110{\mu}m$ $Al_2O_3$ particle, grinding, sandblasting and liner application). One group had received no treatment. These disks were veneered with 3 mm thick and 5 mm diameter Cercon Ceram Kiss porcelain and SBS test was conducted (cross-head speed = 1 mm/min). Two and one way ANOVA, Tukey's HSD Past hoc, and T- test were selected to analyzed the data (${\alpha}=0.05$). RESULTS. In this study, the factor of different types of zirconia ceramics (P=.462) had no significant effect on SBS, but the factors of different surface modification techniques (P=.005) and interaction effect (P=.018) had a significant effect on SBS. Within colored zirconia group, there were no significant differences in mean SBS among the four surface treatment subgroups (P=0.183). Within white zirconia group, "Ground group" exhibited a significantly lower SBS value than "as milled" or control (P=0.001) and liner (P=.05) groups. CONCLUSION. Type of zirconia did not have any effect on bond strength between zirconia core and veneer ceramic. Surface treatment had different effects on the SBS of the different zirconia types and grinding dramatically decreased the SBS of white zirconia- porcelain.

• 자원리싸이클링
• /
• 제26권6호
• /
• pp.50-57
• /
• 2017

본 연구에서는 몽골 플라이애시의 기초물성 및 분쇄과정을 통한 시멘트 혼화재로의 사용가능성을 검토하였다. 몽골 플라이애시는 국내 플라이애시 보다 입자가 컸으며, 구형 입자도 적게 관찰되었다. 몽골 플라이애시의 CaO 함량은 높았으며, 이외 성분은 비슷한 수준이었다. 진동밀 분쇄 후 플라이애시는 $7.9{\mu}m$까지 작아졌으며, 분말도도 증가하였다. 분쇄 플라이애시를 시멘트와 혼합할 경우, 60분 분쇄시 가장 우수한 압축강도 값을 나타내었다. 또한 이들 강도값은 모든 재령에서 OPC 보다도 높은 수준이었다.

• 펄프종이기술
• /
• 제44권4호
• /
• pp.16-24
• /
• 2012

To characterize the coating structure, diverse methods such as mercury intrusion, nitrogen adsorption and oil absorption methods have been developed and widely employed. These indirect techniques, however, have some limitation to explain the actual coating structure. Recently microscopic observation methods have been tried for analyzing structural characteristics of coating layers. Preparation of the undamaged cross section of a coating layer is essential for obtaining high quality image for analysis. In this study, distortion-free cross-section of the coating layer was prepared using a grinding and polishing technique. The coated paper was embedded in epoxy resin and cured. After curing the resin block it was ground with abrasive papers and then polished with diamond particle suspension and nylon cloth. Polished coating layer was sufficient enough to obtain undamaged cross sectional images with scanning electron microscope under backscattered electron image mode. In addition, the SEM images allowed distinction of the coating layer components. Also S/B latex film formed between pigment particles was visualized by osmium tetroxide staining. Pore size distribution and pore orientation were evaluated by image analysis from SEM cross-sectional images.