• Journal of the Korean Electrochemical Society
• /
• v.18 no.2
• /
• pp.68-74
• /
• 2015

To compare the microstructure and electrochemical properties between two binary alloys (Cr-Si, Ni-Si), two composition of binary alloys with the same capacity were selected using phase-diagram and prepared by matrix-stabilization method to suppress the volume expansion of Si by inactive-matrix. Master alloys were made by Arc-melting followed by fine structured ribbon sample preparation by Rapid Solidification Process (RSP, Melt-spinning method) under the same conditions. Also powder samples were produced by wet grinding for X-Ray Diffraction (XRD) and electrochemical measurements. As predicted from the phase diagram, only active-Si and inactive-matrix ($CrSi_2$, $NiSi_2$) were detected. The results of Scanning Electron Microscope (SEM) and Transmission Electron Microscopy - Energy Dispersive X-ray Spectroscopy (TEM-EDS) show that Cr-Si alloy has finer microstructure than Ni-Si alloy, which was also predictable through phase diagram. The electrochemical properties related to microstructure were evaluated by coin type full- and half-cells. Separately, self-designed test-cells were used to measure the volume expansion of Si during reaction. Volume expansion of Cr-Si alloy electrode with finer microstructure was suppressed significantly and improved in cycle capability, in comparison Ni-Si alloy with coarse microstructure. From these, we could infer the correlation of microstructure, volume expansion and electrochemical degradation and these properties might be predicted by phase diagram.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.4
• /
• pp.362-367
• /
• 2006

Waste activated sludge(WAS) collected from domestic wastewater treatment plant is biomass that contains large quantities of organic matter. However, relevant literature show that the bio-hydrogen yield using WAS was too low. In this study, the effect of pretreatment of WAS on hydrogen yield was investigated. Pretreatment includes acid and alkali treatments, grinding, heating, ozone and ultrasound methods. After pretreatment organic matters of WAS were solubilized and soluble chemical oxygen demand(SCOD) was increased by 14.6 times. Batch experiments were conducted to investigate the effects of pre-treatment methods and buffer solution, hydrogen partial pressure, and sodium ion on hydrogen production from WAS by using heated anaerobic mixed cultures. Experimental results showed that addition of buffer solution, efficient pre-treatment method with alkali solution, and gas sparging condition markedly increased the hydrogen yield to 0.52 mmol $H_2/g$-DS.

• Korean Journal of Ecology and Environment
• /
• v.43 no.2
• /
• pp.221-231
• /
• 2010

A simple extraction method was applied to control four selected cyanobacteria, solitary (SMA) and colonial Microcystis aeruginosa (CMA), and green algae, Scenedesmus quadricauda and Chlorella vulgaris using a domestic plant and mineral. Three kinds of concentrations (1, 5, and 10 mg $L^{-1}$) of three fresh plants Camellia sinensis, Quercus acutissima, and Castanea crenata, three minerals loess, quartz porphyry, and natural zeolite, and plant-mineral composite, totally seven materials were prepared with the simple extraction processes: drying and grinding of material, water-extraction by high temperature-sonication and filtering. Cyanobacteria SMA and CMA (over 60% of control) were effectively inhibited with the low concentration (1 mg $L^{-1}$) of plants Q. acutissima and C. crenata and natural zeolite, while green alga S. quadricauda (below 50% of control) also retarded in growth. Low concentrations (1 mg $L^{-1}$) of C. sinensis effectively increased the growth of C. vulgaris, while loess also induced the algal growth of S. quadricauda. Therefore, our results indicate that crude extract of domestic plants, Q. acutissima and C. crenata can be also useful to control the cyanobacterial bloom in eutrophic lake, whereas C. sinensis and loess may be a good growth factor or useful media for the algal mass culture.

• Korean Journal of Heritage: History & Science
• /
• v.43 no.3
• /
• pp.102-121
• /
• 2010

Three bronze bells excavated from the Hoeamsa temple site were investigated for their microstructures and chemical compositions in an effort to understand the technology applied in fabrication, which may represent the related industry established in the early Joseon period. The result shows that the bells were cast from alloys of approximately 85% copper-8% tin-7% lead. The chemical analysis for ten trace elements shows that they were all kept below 0.3 weight %, suggesting that the alloys were made of relatively well-refined copper, tin and lead. The presence of sulfur and iron indicates that chalcopyrite or chalcocite may have been used in the smelting of copper. Evidence has been found that the bells were cast by pouring the liquid metal from the top of the sand molds that were set up in an upright position. No additional treatments, thermal or mechanical, other than a little grinding were applied upon the completion of casting. After the shaping process, a balancing plate was attached to the top of the bell using a steel connection ring. The connection assembly was then fixed to the main body by using molten bronze as a solder. The surface inscription was found carved using different techniques. The differences in the order of strokes and the calligraphic style indicate that the carving was carried out by more than one master. In the absence of documentary evidence on past bronze technology, the present bronze bells with known chronology, provenance and the main agent of production, prove to be a rare and valuable archaeological material for the understanding of the related technology in use in the early Joseon period.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.5
• /
• pp.799-810
• /
• 2022

Welding work is a production work method widely used throughout the industry, and various types of welding technologies exist. In addition, many methods are being studied to automate these welding operations using robots, but in the ship manufacturing field, welding such as painting, cutting, and grinding is also the most common operation, but the manual operation ratio is higher than in other industries. Such a high manual labor ratio in the field of ship manufacturing not only causes quality problems and production delays according to the skill of workers, but also causes problems in the supply and demand of manpower. Therefore, this paper analyzed the reason why the automation rate is low in welding work at ship manufacturing sites compared to other industries, and analyzed the production process and field environment for small and medium-sized ship manufacturing companies that repeatedly manufactured with a small quantity production method. Based on the analysis results, it is intended to propose a robot system that can easily move between workplaces and secure uniform welding quality and productivity by collaborating simple welding tasks with humans. Finally, the simulation environment is constructed and analyzed to secure the suitability of robot system application to current production site environment, work process, and productivity, rather than to develop and apply the proposed robot system. Through such pre-simulation and robot system suitability analysis, it is expected to reduce trial and error that may occur in actual field installation and operation, and to improve the possibility of robot application and positive perception of robot system at ship manufacturing sites.

• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.3
• /
• pp.227-233
• /
• 2023

Tardive dyskinesia is an involuntary neurological movement disorder caused by long-term use of dopamine receptor-blocking drugs leading to dental implications like uncontrolled gnashing and grinding of teeth which in turn imperil the oral rehabilitation procedures as the excessive load increases the risk of prosthesis fracture. A 40-year male with a medical history of tardive dyskinesia visited the hospital to receive oral rehabilitation for missing maxillary anterior teeth. After the oral examination, tooth preparation was done on teeth 13, 15, and 23. After that silicon impression was made and the gypsum cast was digitalized using a desktop scanner and an interim prosthesis was fabricated by milling a resin block. During the try-in, the occlusal one-third of the interim prosthesis was trimmed, and an auto-polymerizing acrylic resin was applied on the occlusal surfaces and inserted in the patient's mouth. Then, the functionally generated path (FGP) of occluding surfaces of opposing arches was traced on the resin surface. When the resin was hardened, the modified interim prosthesis was removed and digitized using an intraoral scanner. The scan image was used in designing the occlusal morphology of definitive prosthesis by modifying the design of the interim prosthesis using the dual scan method. Lastly, a monolithic zirconia prosthesis was fabricated by milling a zirconia block. The definitive prosthesis was delivered reflecting the patient's occlusal scheme. This case report shows that the FGP technique with the dual scan method can help in fabricating fixed prosthesis with harmonious occlusion in a tardive dyskinesia patient.

• Clean Technology
• /
• v.18 no.4
• /
• pp.379-389
• /
• 2012

Environmental issues are being paid more attention due to income growth, urban overcrowding, and population growth in Korea. Among the various environmental problems, odor damage is the one of the serious factors. To take example for food waste combination treatment in Su-young wastewater treatment plant in Busan, many complaints occurred because this plant locate around residential areas. The purpose of this work is not only to analyze odorous elements and their contributions but also to evaluate odor quotient (OQ), sum of odor quotient (SOQ), and treatment efficiency of bio-filter. The results of dilution sensory test of complex odor, grinder, leachate, hopper indicated higher order complex odors happen in July and August. The main odorous elements consisted of hydrogen sulfide, ammonia, methly mercaptan and acetaldehyde, which were analyzed by instrumental detection method, and methyl mercaptan was exceeded over 3,571 times of threshold. In addition, result of contribution of odor was methyl mercaptan (49.95 to 59.08%), hydrogen sulfide (20.43 to 29.27%), trimethylamine (8.82 to 13.42%) and acetaldehyde (9.17 to 11.35%). Other facilities were compared with the contribution of the odor using OQ and SOQ during the process. Sulfur compounds, acetaldehyde, and trimethylamine are high contribution of odor using OQ as well as odor intensity of grinding process is highest. As a result, sulfur compounds (e.g., methyl mercaptan and hydrogen sulfide) are highest for OQ and SOQ of grinding process is highest as 7,067. The removal efficiency of deodorization equipment was more than 90.00% in ammonia and amines, but the average efficiency of sulfur compounds was 53.51%. Thus, this facility is more higher contribution of acetaldehyde and trimethylamine than other treatment facilities. And food waste treatment in environmental area needs to consider appropriate capacity and refers to other bio-filter operating conditions.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.6
• /
• pp.837-842
• /
• 2010

The physicochemical properties of coarse semolina (CS), medium semolina (MS) and fine semolina (FS) were investigated to research method applied in noodles processing of Korean wheat semolina. Large particle (>250 ${\mu}m$) was over 75% in all semolinas, except for FS, and the particle distribution of MS and durum semolina (DS) was similar. Crude protein and crude ash were the highest in DS followed by CS>MS>FS. Crude lipid of DS was the lowest among samples and CS, MS and FS were not significantly different. L value was high in semolina with small particle distribution and starch damage was the lowest in DS followed by FS>MS. Amylose content was high in DS (29.80%) and FS (29.08%) with small particle distribution. Water binding capacity was the highest in DS, and FS showed the highest water binding capacity among Korean wheat samples. Solubility and swelling power were noticeably high in FS with low starch damage and small particle distribution. In scanning electron microscope (SEM), FS and MS showed distribution of separated fine particles of flours. From these results, the physicochemical properties of semolina showed many differences by grinding methods. FS should be applied in noodles processing through additional examination about characteristic of noodle making.

• The Korean Journal of Food And Nutrition
• /
• v.25 no.4
• /
• pp.1033-1038
• /
• 2012

This study was done to provide basic information about the storage and distribution of specialty grade coffee of which the market will be expanded through customer sensory evaluation according to the storage period of specialty grade coffee by the SCAA classified method with consideration to defective beans and scent. The specialty grade coffee sample of this study was extracted on day 1, day 14, and day 28. The water content showed a significant reduction on the 28th storage day and there was no pH change according to the storage period. Color degree was brightened according to the preservation period before and after grinding but there was no significant difference. The panels for sensory evaluation considered of 24 university. The sensory evaluation consist of aroma, bitterness, and astringency, acidity, aftertaste, overall satisfaction, and items for strength estimation consist of aroma, acidity and bitterness. The sensory evaluation was expressed by applying a 5 point Likert scale. The results showed that as the storage period increased so too did the aroma and the strength of bitterness. Preference was the highest on day 1 in every items except aroma and astrigency. However on day 14 and day 28, most of the sensory evaluation became low and then became high, which was inconsistent. Male students were not consistent in their evaluation according to the preservation period, but female students rated aroma and bitterness the lowest on preservation period day 1 and they prefer after a storage period of 1 day in regards to the entire degree of satisfaction including sour test. astrigency and aftertaste. The analysis of visiting frequency for coffee shops used demonstrated that the longer the preservation period, the lower the preference but was not significant in the case of involving a little frequency group. The group that did not like Americano coffee evaluated that the longer the preservation period, the lower the preference based on Americano coffee preference analysis. There was no consistency between the storage period day 14 and day 28 in strength and preference, but preference for storage period day 1 was high in every group, which means that the quality of coffee is affected by the preservation period.

• Korean Journal of Veterinary Research
• /
• v.42 no.3
• /
• pp.363-370
• /
• 2002

For the development of diagnostic polymerase chain reaction (PCR) to fungal infection by dermatophytes Trichophyton and Microsporum, detection of the fungal DNA by PCR and analysis of the DNA pattern were undertaken in the present study. A total of 15 strains were tested and those consisted of 3 reference strains and 12 isolates such as: reference strains of T mentagrophytes (downy type, ATCC 9533), T rubrum (IFO 6204) and M gypseum (ATCC 9083), and each isolate of T mentogrophytes (powdery type), T mentagrophytes (granular type), T mentogrophytes (purple-red type), T rubrum, T raubitschekii, T tonsurans, T equinum, T ajelloi, T verrucosum, M cookei, M nanum and M gypseum. The DNA were purely isolated from all strains of Trichophyton spp. and Microsporum spp. by a simple method partly consisted of disruption of fungal cells by lyophilization and grinding and extraction of fungal DNA without phenol treatment which is a routine procedure in DNA isolation. For the detection of fungal DNAs, optimal condition of PCR was determined as preheating once at $94^{\circ}C$ for 5 min, 35 cycles of denaturation at $94^{\circ}C$ for 1 min, annealing at $38^{\circ}C$ for 1 min and polymerization at $72^{\circ}C$ for 2 min, and 1 cycle of final extension at $72^{\circ}C$ for 5 min. In PCR using arbitrary primers AP-1 (5' ACCCGACCTG3') and AP-2 (5' ACGGGCCAGT3'), DNAs in various numbers and sizes were detected from different species of Trichophyton and Microsporum, while DNAs in similar size were also detected in all strains of Trichophyton spp. and Microsporum spp. There were unique DNAs observed from certain dermatophytes by AP-1 such as 1,900 bases in T rubrum, 950 and 1,100 bases in T raubitscheldi, 2,100 bases in T equinum, 400 bases in T verrucosum and 1,150 bases in M gypseum. The unique DNAs were also observed by AP-2 such as 1,200 bases in T ajelloi, 250 bases in T verrucosum, 1,150 bases in M cookei and 2,000 bases in M nanum. The results indicated that PCR can detect a specific DNA from certain Trychophyton and Microsporum spp, which can be the information for further development of diagoomc PCR to dennatophytes.