• 한국정밀공학회지
• /
• 제30권5호
• /
• pp.493-498
• /
• 2013

The present study treats the optimization process for a non-linear grinding system with dual time delay, mainly from the energetic viewpoint. To this end, the stability of the grinding system is investigated first with regard to the grinding wheel rotation speed. The concept of grinding energy density is newly proposed as the primary figure of merit and this quantity is evaluated at various stable and limit cycle conditions. The computational results show that simple monotonic trend in energy density is observed under stable conditions, whilst rather complicated behaviors can appear when the conditions are associated with limit cycle oscillations. Finally, the relations between the vibration amplitude and the energy density and their implications on the engineering decision/compromise are discussed.

• 한국정밀공학회지
• /
• 제33권6호
• /
• pp.485-490
• /
• 2016

This study focused on developing an electro-discharge truing method for the ELID grinding process using a metal-bonded grinding wheel. The truing process in grinding plays important roles in enhancing the quality of the ground surface. In this study, a reference current in the electro-discharge truing process was confirmed to be a viable solution for efficient truing through performance experiments. Current and voltage variation experiments were carried out and the variation output data were collected with a monitoring program to understand the electrodischarge phenomenon that occurs between metal-bonded grinding wheels and copper electrodes. The experimental results showed that as the reference current decreased, the average electro-discharge energy decreased. Therefore, the reference current can be used as an indicator to estimate the size of the gap between the truer and grinding wheel.

• 한국생산제조학회지
• /
• 제6권3호
• /
• pp.17-25
• /
• 1997

This paper aims to clarify the effects of grinding conditions on the grinding force, ground surface and chipping size of workpiece in surface grinding of various ferrites with the resin bond diamond wheel. The main conclusions obtained were as follows: In a constant peripheral wheel speed, the specific grinding energy is fitted by straight lines with grinding depth coefficient($\delta$) in a logarithmic graph. The effect of both depth of cut and workpiece speed on grinding energy becomes larger in the order of Mn-Zn, Cu-Ni-Zn and Sr. When using the diamond grain of the lower toughness, the roughness of the ground surface becomes lower. The ground surfaces show that the fracture process during grinding becomes more brittle in the order of Sr, Mn-Zn and Cu-Ni-Zn. The chipping size at the corner of workpiece in grinding increases with the the increases of the depth of cut and workpiece speed, and the decrease of peripheral wheel speed. The effect of both depth of cut and workpiece speed on chipping size becomes more larger in the order of Sr, Mn-Zn and Cu-Ni-Zn.

• 한국세라믹학회지
• /
• 제51권2호
• /
• pp.121-126
• /
• 2014

The influence of a liquid medium duringa wet-milling process in the grinding and oxidation of silicon powder was investigated. Distilled water, dehydrated ethanol and diethylene glycol were used as the liquid media. The applied grinding times were 0.5, 3, and 12 h. Ground silicon powder samples were characterized by means of aparticle size analysis, scanning electron microscopy(SEM), x-ray powder diffraction (XRD), FT-IR spectroscopy and by a chemical composition analysis. From the results of the characterization process, we found that diethylene glycol is the most efficient liquid medium when silicon powder is ground using a wet-milling process. The FT-IR results show that the Si-O band intensity in an unground silicon powder is quite strongbecause oxygen becomes incorporated with silicon to form $SiO_2$ in air. By applying deionized water as a liquid medium for the grinding of silicon, the $SiO_2$ content increased from 4.12% to 31.7%. However, in the cases of dehydrated ethanol and diethylene glycol, it was found that the $SiO_2$ contents after grinding only changed insignificantly, from 4.12% to 5.91% and 5.28%, respectively.

• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.696-701
• /
• 2003

교반형 볼 밀에서 실리카 분말의 열처리에 따른 분쇄효율을 분쇄에 따른 에너지 소비량을 측정함으로써 조사하였다. 열처리를 행한 것과 행하지 않은 시료를 비교해 보면, 600~90$0^{\circ}C$에서 열처리 후 실온에서 냉각된 시료를 건식 분쇄하였을 경우 약 40~50% 정도, 열처리 후 물속에서 급속 냉각한 경우 약 52～62% 정도의 에너지의 감소 효과가 있었다. 또한 열처리한 실리카 분말을 습식 분쇄를 할 경우 건식 분쇄에 비하여 약 40% 정도의 분쇄에너지가 적게 소모되고 있음을 알 수 있었다. 또한 실리카 분말을 열처리 한 후, 급속 냉각할 경우 발생하는 열충격은 입도에 대한 영향을 거의 받지 않으며 분쇄효과를 향상시킴을 알 수 있었다.

• 한국정밀공학회지
• /
• 제14권12호
• /
• pp.66-72
• /
• 1997

This paper aims at reviewing the possibility application over normal or abnormal, detection used by AE and the wear characteristics of grinding process. In this study, when diamond bur in dentistry with chosen grinding conditions were tuned at grinding. The variation of grinding resistance and AE signal is detected by the use of AE measuring system. The tests are carried out in accordance with diamond burs and workpiece: arcyl and bovine. According to the experiment results, the following can be expected: AE has the possibility to detect the state normality and abnormality. Hpwever, the grinding resistance measuring can find it difficult to detect it. It can be accurately excepted from AE occurrence pattern in contact start point of diamond bur and bovine, grinding condition and derailment point. It is known that AErms is well compatible with grinding resistance. According to the increase of the material removal rate, the specific energy of the diamond bur is inclined to dectease and the grinding resistance has a tendency to increase.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.870-873
• /
• 2000

This investigation reports the grinding characteristics of quartz. Grinding experiments were performed at various grinding conditions including wheel mesh, table speed and depth of cut. The grinding forces and specific grinding energies were measured to compare the grindability of quartz with those of structural ceramics such as A1$_2$O$_3$, SiC, Si$_3$N$_4$ and ZrO$_2$. Surface roughness was also measured with tracer and the ground surfaces were observed with SEM. The chip formation energy of quartz was about 6J/㎣, which is quite smaller than those of structural ceramics. Although plastic flows are occured in Si$_3$N$_4$ and ZrO$_2$, micro/macro cracks are occured in ground surface of quartz like in A1$_2$O$_3$ and SiC.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.80-84
• /
• 1996

This paper aims at reviewing the Possibility application over normal or abnormal, detection used by AE and the wear characteristics of grinding process. In this study, when diamond bur in dentistry with chosen grinding conditions were tuned at grinding. The variation of grinding resistance and hE signal is detected by the use of AE measuring system. The tests are carried out in accordance with diamond burs and workpiece; arcyl and bovine. According to the experiment results, the following can be expected; AE has the possibility to detect the state normality and abnormality. However, the grinding resistance measuring can find it difficult to detect it. It can be accurately excerpted from AE occurrence pattern in contact start point of diamond bur and bovine, grinding condition and derailment point. It is known that AE$\_$rms/ is well compatible with grinding resistance. According to the increase of the material removal rate, the specific energy of the diamond bur is inclined to decrease and the grinding resistance has a tendency to increase.

• 한국기계가공학회지
• /
• 제3권1호
• /
• pp.45-51
• /
• 2004

In this paper, the relationship between the mechanical properties of alumina abrasives and grinding performance was investigated. Micro vickers hardness and fracture strength of all abrasives used in this study were measured. The grinding experiments were earned out with alumina grinding wheels made by various kinds of alumina abrasives including 32A, WA, ART, ALOMAX, and RA. The performance of such grinding wheel for grinding SKD11 was evaluated by specific grinding energy, grinding-ratio, and surface roughness. The grinding wheels composed by the harder abrasives and the lower fracture strength abrasives showed better grinding performance.

• 한국정밀공학회지
• /
• 제15권9호
• /
• pp.145-151
• /
• 1998

In this study, the experimental and analytic investigation with cold air system has been performed for improving the working environment of the conventional grinding fluid. Very simple cold air system was developed which could replace by the conventional grinding fluid system. The identification of heat of grinding Bone is very important for precision grinding. The experimental data was analysed to investigate the heat which was transferred to the workpiece. It was found that 45∼55％ of the total energy for dry grinding, 22∼28％ for wet grinding, and 32∼35％ for cold air system are conducted to the workpiece in grinding with cubic boron nitride wheel. Cubic boron nitride wheel could reduce the residual stress and thermal demage comparing with aluminium oxide wheel, because cubic boron nitride wheel has very high extreme thermal conductivity.