• 한국산업융합학회 논문집
• /
• 제25권3호
• /
• pp.357-363
• /
• 2022

In this study, in order to develop an non-slip metal grating, the stability of the grating according to the span of the grating and the gap and height of the bearing bar was evaluated. The optimal shape design of the grating was performed using the results of determining the stability of the grating. The purpose of this study is to determine the stability according to the spacing and height of the bearing bar by applying the design pressure at the design stage to develop the anti-skid grating, and to design the optimal shape for cost reduction. In the optimal design, the target variable was set as the mass, and the optimal design of the grating was performed based on about 20%. Regardless of the height of the bearing bar of the grating, the stress and deformation of the span and the grating showed a proportional tendency to each other, and it was found that the stress decreased as the height of the bearing bar increased. Based on the structural analysis results, an optimal design was performed using mass as the objective variable, and the existing 2mm thickness was changed to 1.6mm, reducing the mass by about 19%. The stress increased by about 4.4% compared to the maximum stress of the existing grating, but the minimum safety factor was 3.1, indicating that the optimally designed grating was stable.

• 한국레이저가공학회지
• /
• 제14권3호
• /
• pp.17-20
• /
• 2011

We fabricated a multi-layer diffraction grating inside fused silica glass by using a femtosecond laser direct writing method. The femtosecond laser with a wavelength of 515 nm, a pulse width of 250 fs, a repetition rate of 100 kHz, and an average output power of 6 W was used. Two layer diffraction grating with a grating period of $6{\mu}m$ was successfully fabricated with the layer gap of 0.5, 1, 2, 3, and $5{\mu}m$, respectively. Also, we investigated the diffraction pattern by illuminating a He-Ne laser beam. Finally, we demonstrated the diffraction grating with a grating period of $3{\mu}m$ by adjusting the gap of each layer with a grating period of $6{\mu}m$. Femtosecond laser direct writing technology of multi-layer has a potential to fabricate the diffraction grating with a grating period of below $1.5{\mu}m$.

• 한국산업융합학회 논문집
• /
• 제24권4_2호
• /
• pp.501-507
• /
• 2021

In this study, In order to prevent the safety accidents caused by the sliding, to develop the non-slip grating, the stability judgment based on the span length of the grating and the gap of the bearing bar is performed. The structural analysis of Grating was carried out in accordance with the provisions set out in Grating's load-bearing test conditions. As the span length increases, the deflection increases and the stress and span length tend to be proportional to each other. It was shown that the larger the span, the linear increase in stress and exponential increase in deformation of grating. The maximum stress of grating was approximately 58.2 MPa, indicating a very stable safety rate of about 4.3 compared to the yield strength of the grating material. Based on these results, it will be able to be utilized as the basic data for determining the optimal dimensions of non-slip grading by performing optimal designs in the future.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 추계종합학술대회 논문집(2)
• /
• pp.313-316
• /
• 2000

Concentric-Circle-Grating (CCG) cavity is analyzed by coupled mode theory. In this case concentric grating is acting as both feedback element and output coupler. In our calculations radiation loss terms are included in guided coupled mode equations. The surface-emitted field distribution is obtained in self-consistent manner.

• 한국전기전자재료학회논문지
• /
• 제17권9호
• /
• pp.994-1000
• /
• 2004

We studied the characteristics of annular phase gratings as spatial frequency filters. We first calculated the Fraunhofer diffraction patterns of annular gratings and then got the modulation transfer function (MTF) from the zeroth order Hankel transform of the intensity distribution function. Binaryphase annular grating shows higher diffraction efficiency than binary phase rectangular grating. But the MTF decreases linearly in the low-frequency region as that of rectangular grating does. The diffraction pattern of 4-phase annular grating is similar to that of 2-phase grating and hence MTFs of the two are much alike. For 8-phase annular grating, the 7th order diffracted beam is the lowest one next to the first. Consequently, the diffraction efficiency is very high and the MTF graph is curved upward. The diffracted beams except the first order are negligible and hence the MTF characteristics are more improved in the case of 16-phase grating. But the degree of improvement becomes lowered c(Impaled with 8-phase grating. We made a 16-phase annular grating and measured its MTF. The experimental result agrees well with the calculated one.

• 전기학회논문지
• /
• 제59권5호
• /
• pp.922-926
• /
• 2010

We have investigated the grating coupled surface plasmon resonance (GC-SPR) sensors using ZnO nano-grating structures to enhance the sensitivity of an SPR sensor. The GC-SPR sensors were analyzed using the finite-difference time-domain method. The optimum resonance angles of 49 degrees are obtained in the 150 nm wide grating structure with a period of 300 nm for the ZnO thickness of 30 nm. Then, the ZnO nano-grating patterns were fabricated by using laser interference lithography. The measured resonance angle of nano-grating patterns was around 49 degrees. Here, an enhanced evanescent field is obtained due to the surface plasmon on the edge of the bandgap when the ZnO grating structures are used to excite the surface palsmon.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2000년도 제11회 정기총회 및 00년 동계학술발표회 논문집
• /
• pp.1-1
• /
• 2000

The interaction of light with periodic patterns generates beautiful color patterns and interesting applications. The basic equation for understanding this phenomena is the grating equation. It tells us the angles, relative to a perpendicular to a grating with a specific period, into which light of a specific wavelength will be diffracted. But what it does not tell us is how much light will be directed into the various "orders" of the grating. It was found that by controlling the shape of the diamond point used to cut the periodic structure into the substrate, a traditional grating could be made to direct most of the light diffracted from it into a single order. This type of grating is referred to as a "blazed" grating. (omitted); grating. (omitted)

• 한국광학회지
• /
• 제7권4호
• /
• pp.370-374
• /
• 1996

Superstructure Grating Distributed-Bragg Reflector(SSG DBR) 레이저는 비교적 높은 Mode Suppression Ratio(MSR)을 가지면서 넓은 파장 대에서 불연속 파장가변 특성을 가진다. 그러나 SSG DBR 레이저는 출력파장을 가변 시킬 때 파장가변 영역을 구성하는 채널 중 몇 개가 빠지는 현상이 실험을 통해 관찰되어 왔다. 우리는 수치해석적인 시뮬레이션을 통해 이 현상이 SSG DBR 거울을 구성하는 linearly chirped grating의 불균일한 반사 피크 높이에 의한 영향임을 발견했고 반사율 피크 높이를 거의 균일하게 만들 수 있는 nonlinearly chirped grating을 제안한다. 그리고 이 거울을 가지는 파장 가변 레이저가 채널의 손실 없이 넓은 파장가변 영역에서 동작하는 것을 확인했다. 그러므로 nonlinearly chirped grating을 가지는 DBR 거울은 넓은 파장가변 영역을 가지는 가변 레이저에 적용할 수 있다.

• 한국광학회지
• /
• 제18권2호
• /
• pp.142-148
• /
• 2007

기계적으로 유도되는 장주기 광섬유 격자 배열 소자를 제작하고 격자 배열소자의 광 투과 특성을 측정하였다. 격자 배열 소자는 표면에 $690{\mu}m$부터 $780{\mu}m$ 주기까지 $10{\mu}m$씩 주기가 증가되는 격자들이 만들어져 있는 45 cm 길이의 금속 막대와 고무덮개로 구성되어 있다. 외부 압력이 격자 배열 소자에 인가되면 압력이 인가된 지점에만 장주기 광섬유 격자가 형성되고 장주기 광섬유 격자의 공진 파장은 인가된 지점에 의존한다. 그리고 제작된 장주기 광섬유 격자 배열 소자의 특성측정 결과가 다양한 투과 특성을 갖는 광섬유 대역 제거 필터, 혹은 압력센서로 사용 가능함을 보여주고 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.402-406
• /
• 1995

The shadow moire is one the optical techniques which able to give contour lines of an object with respect to a master grating plane. The moire patterns are issued from the superposition of a grating and its shadow projected on the surface of an object. But in the conventional shadow moire method the reference grating and deformed grating are mutually dependent, it is impossible to obtain uniform phase shifts on the whole field by moving the reference grating. Here we propose ane trial to apply phase shifting to conventional shadow moire. When, in the conventional arrangement, Phase-shifting that is sctually constant regardless of fringe orders is achieved by moving the grating and the light source. Finally we obtained a better result by using this procedure and applied the phase shifting shadow moire to three dimensional measurement.