• Journal of the Korean Ceramic Society
• /
• v.56 no.5
• /
• pp.443-452
• /
• 2019

In this study, TiO₂-polyvinyl alcohol (PVA) composite granules were prepared via spray drying technique. To investigate the effects of solid content and binder/powder ratio in the slurry on the granulation behavior of TiO₂ powders, the feed compositions were designed to vary over a wide range. The morphology, actual densities, and average granule size and size distribution of the TiO₂-PVA composite granules were characterized by using scanning electron microscopy technique, a gas pycnometer, and an image analyzing program (Image-J), respectively. The results indicate that solid content and the amount of PVA in the feedstock slurry are the dominant factors determining the granule morphology, size, and size distribution of TiO₂-PVA composite. Moreover, it was observed that increasing the solid content and the amount of PVA in the slurry improved the granulation process and reduced the granule defects. For the preparation of spherical TiO₂-PVA composite granules with the minimum amount of non-granulated powders, the optimized composition of the feedstock slurry was found to be 35 wt.% solid and 3 wt.% PVA.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.1
• /
• pp.22-27
• /
• 2017

$TiO_2$ films, thickness of $1{\sim}30{\mu}m$ were deposited on glass substrate at room temperature by room temperature granule spray in vacuum. The starting powder was calcinated at $600^{\circ}C$ for 4 h using $Al_2O_3$ crucible in the furnace. The particle size of the $TiO_2$, $1.5{\mu}m$ was measured by a particle size analyzer. The effect of different process parameters such as number of pass, gas flow rate and feeder voltage was studied. As the number of passes increased, the film thickness increased proportionally due to adequate kinetic energy conserved. The effect of three different flow rates (i.e. 15, 25, and 35 LPM) on deposited film was investigated. As gas flow rate increased, the film thickness increased up to 25 LPM and then decreased. Higher feeder voltage with low flow rate of 15 LPM resulted in unsufficient coating thickness due to insufficient kinetic energy. Microstructure of $TiO_2$ films was investigated by scanning electron microscope and high resolution tramission electron microscope.

• Korean Journal of Food Science and Technology
• /
• v.21 no.4
• /
• pp.528-535
• /
• 1989

Starches isolated from Seipoong and Daeji potato were classified into small and large granules. The starch granule size for Seipoong and Daeji was in the range of $10-85\;{\mu}m$ and $13-90\;{\mu}m$, respectively. Seipoong starch contained more large granules $(>41\;{\mu}m)$ while Daeji starch had more small granules $(<30\;{\mu}m)$. There was no difference in water-binding capacity both between two starches and among granule sizes. Amylose content for toro starches was the same but was higher in large starch granules than small ones. Swelling powder at $80^{\circ}C$ for parent starches was essentially the same but small starch granules had much higher swelling powder than large ones. The large starch granules for Daeji showed higher peak viscosity by amylograph than small starch granules. No such difference was observed for Seipoong starch. The gelatinization temperature range of small starch granules was wider than that of large ones, but gelatinization enthalpy was the same between large and small starch granules. The starches regardless granule sizes were completely gelatinized at $70^{\circ}C$.

• Journal of Korea Society of Industrial Information Systems
• /
• v.8 no.3
• /
• pp.105-110
• /
• 2003

The purpose of this paper is to development of micro particle powder feeding systems for the reduction of air leakage of the feeding system. Most of the powder-granule supply systems using compressed air supply have a large amount of air leakage interference. The results of this study lead to reduce air leakage rate by over 50% and to save production cos by. 60%.

• Korean Journal of Weed Science
• /
• v.17 no.2
• /
• pp.135-138
• /
• 1997

Sulfonylureas are highly active herbicides which can be applied at very low rate(10-50g/ha) to control broadleaf weeds. The nature of this category of compound is, however, very unstable toward hydrolysis. Therefore, the preparation of these compounds as liquid formulation was not possible. Most of the current formulations of sulfonylurea are in dry forms such as water dispersible granule or wettable powder. Even in these dry forms, the active ingredients also encounter significant chemical decomposition. This study involves the preparation of the sulfonylurea salts by reacting the parent compound with base such as sodium hydroxide. The salt becomes stable toward hydrolysis and it turns soluble when diluted with water. This discovery makes the preparation for liquid formulation or soluble granule of sulfonylurea possible. The stoichiometry of base added to the neutral sulfonylurea is controlled quite precisely. The base has to be added enough to quench the acidic impurities in the technical material and to convert the active ingredient into salt. However, the base should not be overused to cause further saponification of the sulfonylurea salts. The chemical nature of these compounds is presented and the chemical reaction is described. New soluble liquid formulation and solid granule formulation of sulfonylurea are suggested.

• Nuclear Engineering and Technology
• /
• v.51 no.1
• /
• pp.198-206
• /
• 2019

A new methodology to analyze the nuclear material accountability for pyroprocessing system is developed. The $Pu-to-^{244}Cm$ ratio quantification is one of the methods for Pu accountancy in pyroprocessing. However, an uncertainty in the $Pu-to-^{244}Cm$ ratio due to the non-uniform composition in used fuel assemblies can affect the accountancy of Pu. A random variable, LOPu, is developed to analyze the probability of detection for Pu diversion of hypothetical scenarios at a pyroprocessing facility considering the uncertainty in $Pu-to-^{244}Cm$ ratio estimation. The analysis is carried out by the hypothesis testing and the event tree method. The probability of detection for diversion of 8 kg Pu is found to be less than 95% if a large size granule consisting of small size particles gets sampled for measurements. To increase the probability of detection more than 95%, first, a new Material Balance Area (MBA) structure consisting of more number of Key Measurement Points (KMPs) is designed. This multiple KMP-measurement for the MBA shows the probability of detection for 8 kg Pu diversion is greater than 96%. Increasing the granule sample number from one to ten also shows the probability of detection is greater than 95% in the most ranges for granule and powder sizes.

• Food Science and Preservation
• /
• v.12 no.6
• /
• pp.572-577
• /
• 2005

This study was conducted to investigate the effect of binding agents on the physicochemical characteristics of granule prepared by Lentinus edodes. The mushroom powder was mixed with com starch, lactose, gelatin, gum arabic, or dextrin(DE=23), and the mixtures were passed to granule sieve. Solubility of granule was in the following order, gum arabic>gelatin>lactose, dextrin>corn starch. L value was in the following order, com starch, lactose>gelatin, gum arabic, dextrin. a value and pH were not affected by the binding agents. b value was in following order, lactose, corn starch>gelatin, gum arabic>dextrin. Viscosity was in the following order, gelatin, corn starch>gum arabic, dextrin>lactose. Water absorption was in the following order, gelatin>lactose>corn starch>dextrin>gum arabic. Sugar content was in the following order, gum arabic>lactose, dextrin>corn starch, gelatin. Protein content was the highest in granule formed with gelatin. These results suggested that gum arabic can be utilized for improving solubility and lowering absorption of Lentinus edodes granule as binding agent.

• Applied Chemistry for Engineering
• /
• v.22 no.6
• /
• pp.642-647
• /
• 2011

The fabrication characteristics of porous uranium oxide granules from $U_3O_8$ powder was investigated in terms of initial particle bed motions such as slumping and rolling, thermal treatment conditions, and rotational velocities in slumping motion using a rotary voloxidizer. With respect to the initial particle bed motion the recovery rate of granule of above 1 mm in slumping motion was higher than that in the rolling motion. Rolling motion was changed into slumping motion with high slumping frequency by formation of granules from fine particles. Recovery rate of granule significantly increased with the increas in thermal treatment temperature and time of upto 10 h. As the rotational velocity of voloxidizer in the case of the initial particle bed showing slumping motion increased, the recovery rate of granule increased from 81.5 to 88.7%. However, the rotational velocity of 2 rpm provided an effective density, crushing strength and sphericity of granules.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.9
• /
• pp.1311-1316
• /
• 2015

The aim of this study was to investigate the quality characteristics and antioxidant activities of herbal medicine extract granules for the comparison of commercial powder products such as adlay tea powder and roasted grain powder. The antioxidant activities of samples were estimated using reducing power, 1,1-diphenyl-2-picrylhydrazyl (DPPH) and 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) free radical scavenging activities, and total polyphenolic contents. Herbal extract granules contained $126.44{\pm}7.26mg/100g$ of total polyphenolic contents. Interestingly, the highest antioxidant activity was found in 5.5% herbal extract granules, which showed DPPH and ABTS free radical scavenging activities of 71.82% and 85.28%, respectively, at 100 mg/mL and reducing power of O.D 1.25. These results suggested that addition of herbal medicine extract had beneficial effects on the functionality of granules without any affecting on its sensory characteristics.

• Journal of the Korean Ceramic Society
• /
• v.53 no.3
• /
• pp.332-337
• /
• 2016

As a case study on yttria stabilized zirconia ceramics, the sintering characteristics of submicron powders and the granulation prepared by two-fluid spray drying of submicron particles were investigated. As-received powders of yttria stabilized zirconia particles were reduced to a uniform size of less than about 200 nm by repeated milling. Granulation size obtained by the two-fluid spray drying was affected by the organic matter and the primary particle size. Sintering behavior such as porosity, water absorption ratio, density, and transparency was influenced by processing conditions of the powder, and the discontinuous interfaces in a green body were reduced.