• Geomechanics and Engineering
• /
• 제16권5호
• /
• pp.483-493
• /
• 2018

Experimental study of the deterioration of high-temperature rock subjected to rapid cooling is essential for thermal engineering applications. To evaluate the influence of thermal shock on heated granite with different temperatures, laboratory tests were conducted to record the changes in the physical properties of granite specimens and the dynamic mechanical characteristics of granite after rapid cooling were experimentally investigated by using a split Hopkinson pressure bar (SHPB). The results indicate that there are threshold temperatures ($500-600^{\circ}C$) for variations in density, porosity, and P-wave velocity of granite with increasing treatment temperature. The stress-strain curves of $500-1000^{\circ}C$ show the brittle-plastic transition of tested granite specimens. It was also found that in the temperature range of $200-400^{\circ}C$, the through-cracks induced by rapid cooling have a decisive influence on the failure pattern of rock specimens under dynamic load. Moreover, the increase of crack density due to higher treatment temperature will result in the dilution of thermal shock effect for the rocks at temperatures above $500^{\circ}C$. Eventually, a fitting formula was established to relate the dynamic peak strength of pretreated granite to the crack density, which is the exponential function.

• Geomechanics and Engineering
• /
• 제12권6호
• /
• pp.919-933
• /
• 2017

A series of Brazilian tests under diameter compression for disc specimens was carried out to investigate the strength and failure behavior by using acoustic emission (AE) and photography monitoring technique. On the basis of experimental results, load-displacement curves, AE counts, real-time crack evolution process, failure modes and strength property of granite specimens containing two pre-existing holes were analyzed in detail. Two typical types of load-displacement curves are identified, i.e., sudden instability (type I) and progressive failure (type II). In accordance with the two types of load-displacement curves, the AE events also have different responses. The present experiments on disc specimens containing two pre-existing holes under Brazilian test reveal four distinct failure modes, including diametrical splitting failure mode (mode I), one crack coalescence failure mode (mode II), two crack coalescences failure mode (mode III) and no crack coalescence failure mode (mode IV). Compared with intact granite specimen, the disc specimen containing two holes fails with lower strength, which is closely related to the bridge angle. The failure strength of pre-holed specimen first decreases and then increases with the bridge angle. Finally, a preliminary interpretation was proposed to explain the strength evolution law of granite specimen containing two holes based on the microscopic observation of fracture plane.

• 지질공학
• /
• 제11권2호
• /
• pp.215-227
• /
• 2001

충북 보은 일대에 분포하는 옥천계 지층 및 중생대 화강암을 대상으로 기반암의 지진파 속도 및 시편으로부터 3차원적인 지진파의 전달속도를 측정하고, 이의 결과 자료를 비교분석 하였다. 야외에서 측정된 P파의 평균속도는 불국사화강암이 2697m/s로서 최대이고 구룡산층2에서 861m/s로 최소의 속도를 보인다. 각 방위에 따른 P파의 이방성을 암종별로 비교하면 불굴사화강암에서 최대치(81%)를 장리층에서 최소치(46%)를 보이고, 8곳의 평균 이방성지수는 68.5%이다. 시료에서 측정된 P파의 평균속도를 비교하여 보면 구룡산층1, 구룡산층2,창리층 및 문주리층2에서 5000m/s이상이며, S파의 경우도 동일한 시료에서 3500m/s 이상의 높은 속도가 측정되었는데 이는 야외의 경우보다 3∼5배의 빠른 속도를 나타낸다. 또한 P파의 이방성지수는 불국사화강암과 구룡산1에서 60% 이상의 높은 수치를 보이나 다른 시료에서는 30%이하의 낮은 수치를 보인다. 이 수치는 야외에서 측정된 P파의 평균이방성지수 68.5%보다 현저히 낮은 수치로서 야외에서 측정된 P파의 방향에 따른 속도 차이가 시료의 경우보다 현저히 높았음을 뜻한다.

• 한국지반환경공학회 논문집
• /
• 제5권1호
• /
• pp.35-46
• /
• 2004

화강암질은 우리나라의 3분의 1을 차지하고 있으며, 특히 화강풍화지반은 우리나라 전역에 걸쳐 널리 분포하고 있다. 화강풍화지반은 민감한 입자 구조를 가지고 있어 비교란시료를 채취하기가 매우 어려우며 이로 인해 대부분의 연구는 재성형 시료로 수행되어 지고 있는 실정이다. 그러므로 비교란 또는 재성형 시료로 부터 얻어지는 탄성계수와 감쇠비 등의 변형특성을 비교하는 것은 신뢰성 있는 지반 거동을 이해하는데 중요하다. 본 눈문에서는 국내 화강풍화지반에 대해 다양한 공진주/비틂전단시험을 수행하였다. 그리고 화강풍화지반에 있어 비교란, 재성형 시료 각각의 탄성계수와 감쇠비 등의 변형특성이 비교되고 평가되었다.

• 지질공학
• /
• 제12권3호
• /
• pp.273-284
• /
• 2002

화강암의 응력하에서의 손상발달특성을 연구하기 위해 국내의 조립, 중립, 세립 화강암 시료를 채취하였으며, 일축압축에 의한 손상 전과 후에 탄성파속도시험, 투수성시험이 시료의 물리적 특성을 파악하기 위해 수행되었고, 시료의 단면에 발생된 크랙의 육안관찰을 용이하게 하기 위하여 셀롤로즈 아세테이트 필름 복제법이 사용되었다. 그리고 아세테이트필 상의 크랙을 좀더 명확하게 촬영하기 위해, 암시야조명을 이용한 근접촬영법이 적용되었다. 개인용 컴퓨터와 그래픽 프로그램을 이용하여 크랙을 확대 후 스케치하여 측정함으로써 시료단면에 발생한 크랙을 입도 별로 비교 분석하였다. 손상이 발생한 후, 조립·중립화강암이 세립화강암에 비해 상대적으로 더 낮은 탄성파속도, 더 높은 투수성을 가졌으며, 더 많은 크랙 발생을 보였다.

• 화약ㆍ발파
• /
• 제29권1호
• /
• pp.34-40
• /
• 2011

본 연구에서는 가곡광산 화강암의 변형거동에 열응력과 수압이 미치는 영향을 평가하였다. 열응력과 수압이 미치는 영향을 해석하기 위하여 화강암 시험편에 열을 가하여 200, 300, 400, 500, 600, $700^{\circ}C$ 예열시험편을 제작하였고, 500, 600, $700^{\circ}C$ 예열시험편에 7.5MPa의 수압을 가하였다. 예열시험편에 대한 일축압축시험 결과 예열온도가 증가함에 따라 시험편의 축변형률 및 횡변형률이 증가하는 것으로 나타났으며 특히 $600^{\circ}C$ 이상 시험편에서 변형률의 증가가 현저한 것으로 나타났다. 온도에 따라 시험편의 일축압축강도와 탄성계수는 지수적으로 감소하는 것으로 측정되었다. 수압을 받은 시험편은 그렇지 않은 시험편에 비해 비탄성적인 변형거동이 큰 것으로 나타났으며 이는 수압이 예열시험편 내에 존재하는 균열의 확장과 개구에 영향을 미친다는 것을 뜻한다.

• 터널과지하공간
• /
• 제2권2호
• /
• pp.251-264
• /
• 1992

In this study, the size effect in measuring the fracture toughness of rock was investigated using the ISRM Suggested Method for Fracture toughness using Chevron Bend Specimens. Total 58 specimens were prepared with 4 different diameters, 29, 42, 54, 68mm and center cut-chevron notch. In addition to this, to evaluated the effect of anisotropy of Jecheon granite, which is the sample for this study, core drilling direction was adjusted perpendicular(short transverse) and parallel(arrester) to the rift plane in the sample and the measured fracture toughness for each direction were compared. Important results obtained from this study are as follows. Level ll test condition is more adequate than l, because of low data scattering and precision and corrected fracture toughness of Jechoen granite measured and 2.2MPa{{{{ SQRT { m} }}}} for arrester direction with minimum initial crack length 0.7cm. From the relationship between core diameter and initial crack length presented in the ISRM testing method, the specimen diameter should be bigger than 47mm. The fracture toughnesses measured for arrester and short transverse directon show 10% difference. This is to the anisotropy of Jecheon granite possessing rift plane.

• Geomechanics and Engineering
• /
• 제33권4호
• /
• pp.393-400
• /
• 2023

Displacements near crack and stress intensity factor (SIF) are key parameters to solve rock failure issue when using fracture mechanics. In order to study the horizontal displacement and stress intensity factor of the mode I fracture, a series of three-point bending tests of granite specimens with central notch were carried out. The evolution of horizontal displacements of precast notch and crack tip opening displacements (CTOD) were analyzed based on the digital image correlation (DIC) method. Stress intensity factors for three-point bending beams with arbitrary span-to-width ratios(S/W) were calculated by using the WU-Carlsson analytical weight function for edge-crack finite width plate and the analytical solution of un-cracked stress by Filon. The present study provides a high efficient and accurate method for fracture mechanics analysis of the three-point bending granite beams.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.89-96
• /
• 1994

This study is to develop a new composite material, a mixture of epoxy resin and granite aggergates which is called Expoxy-Granite, to overcome the inherent disadvantages of conventional materials commonly used as a bed structure material of long-term dimensional/ thermal stability. Under the various manufacturing conditions which could be formulated through experimental investigation, we have constructed 6 kinds of Epoxy-Granite structure models having one fifth the size of the ultra-precision machine tool bed structure. They are compared with cast iron and pure granite models through the dynamic test and the thermal deformation test. Both in the steel ball dropping test and in the forced vibration test, three types of epoxy-granite models made in this study have shown much better dynamic characteristics than the cast iron model and almost the same characteristics as compared with the pure granite model. In the thermal deformation test the above composite materials have also represented lower thermal displacements in the vertical direction of each model as compared with other specimens. It is therefore seen that the epoxy-granite complsite material can be applied to the construction of high-precision machine tool bed, instead of cast iron or pure granite.

• 한국농공학회논문집
• /
• 제49권4호
• /
• pp.63-70
• /
• 2007

The soil samples used in this study were prepared with the residual granite soils passed through the #4 sieve and obtained from Pocheon in Gyeonggi-Ki do. Specifically, five types of samples were prepared. Sample A which is a natural state soil was classified as SM according to the uses. Samples of B, C, D, and E were prepared by mixing Sample A with bentonite and were classified as SC according to the uses. The plasticity indexes of samples B, C, D, and E were 15, 25, 30, and 40, respectively. The specimens, whose dimensions are 100mm by 127.5mm, were prepared by A method of ASTM D 698 with the Proctor mold. In experiments, the loading with the 1%/min was applied. Four different disk diameters, 13mm, 26mm, 38mm, and 52mm were used in the Improved Unconfined Penetration (IUP) tests. To compare the tensile strengths, the split tensile tests were also conducted on the same specimens used for the IUP tests. To find out the effects of moisture contents, plasticity Index of specimens on the tensile strength, six different water contents were used for making a specimen.