• Journal of the Korea Furniture Society
• /
• v.23 no.1
• /
• pp.57-67
• /
• 2012

Recently, shows the possibility of providing such dyed-gathered woods after forming single boar This studyds with using cheap timbers generated by the thinning. It is helpful for master artisans are suffering from finding qualified materials. Traditionally, the master artisan has been used the beautiful grained wood from around roots of old zelkova trees and black persimmon trees. Instead, this study shows that dyed-gathered woods replace the natural grained wood and also produces a furniture made of an aggregate and a plate from walnut trees and ash trees which are a contrast to dyed-gathered woods. Dyed-gathered woods can reproduce the various colors to satisfy people's tastes, and the dignified grains that we can see in the old woods. Besides, dyed-gathered woods can replace rare materials and provide higher reliability of supplies.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.1
• /
• pp.55-68
• /
• 1989

This experiment was carried out to investigate the crack of coated Nitrocellulose Lacquer on flatand edge-grained boards of Quercus acutissima, ring-porous wood, and Betula platyphylla var. japonica, diffuse-porous wood, by variations of moisture contents at 7, 13 and 21%. Cold check system was used as an accelerating method for crack development, in which one cycle of the system consisted of 10 replications of each unit cycle, $60^{\circ}C$ for 4hr followdd by $-20^{\circ}C$ for 4hr. The analysis of Nitrocellulose Lacquer characteristics was made by means of water permeation measurement, F.T.I.R. spectroscopy, N.M.R. spectroscopy, gel permeation chromatography, gas chromatography, and D.S.C. The results obtained were as follows: 1. The number of cracks increased with the increasing moisture content of board. 2. The crack of coated film on flat-grained board was fewer in number than on edge-grained board. 3. The crack occurred in Quercus acutissima was more numerous on edge-grained board but less frequent on flat-grained board compared with that in Betula platyphylla var. japonica, respectively. 4. The cold crack vertically developed to the grain both in Quercus acutissima and Betula platyphylla var. japonica. 5. Water permeability in intermediate coated film was lower than in under and top coated film, but the difference was not confirmed between under and top coated film.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.1-6
• /
• 1999

European spruce and maple were to be estimated as raw material of violin family instruments with linear modal analysis to provide the information data for the design of their bodies. Wood specimens cut in different direction were excited by impact hammer to measure the resonant frequency with typical vibrational modes. In spite of lower density than maple, European spruce showed the excellent acoustical properties with higher resonant frequency. And edge-grained spruce had more even frequencies than flat-grained ones to be more acceptable as front plate of violin. Resonant frequency was positively correlated with wood density of each specimen and the coefficients of edge-grained specimens were higher than those of flat-grained specimens of both wood species.

• Journal of the Korea Furniture Society
• /
• v.13 no.2
• /
• pp.19-28
• /
• 2002

This study was carried out to investigate the wood properties for efficient utilization of warm temperate tree species. The tested species were Actinodaphne lancifolia Meisn. grown in Korea. Fundamental wood properties such as anatomical, physical and mechanical properties and chemical components were examined. This species was diffuse porous, straight grained and fine textured wood. The heartwoods of this species was not distinguished clearly to the sapwoods. This species had moderate specific gravity, shrinkage, and mechanical properties. And this species had high content of the extractives by organic solvent.

• Journal of the Korean Wood Science and Technology
• /
• v.19 no.3
• /
• pp.19-26
• /
• 1991

This study was carried out to investigate the solid wood bending properties of red pine(Pinus densiflora S. et Z.)naturally grown in Korea by boiling treatment The specimens were green and their dimension was $15\times15\times350mm$. The optimum conditions for solid wood bending processing of pine lumber are shown in Table 6 and the minimum solid bending radius was 240 mm in boiling treatment. The effects of knot on the degradation of bending processing properties were very severe and the failures of diagonal and torn grained wood were 20% and 30% respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.23-30
• /
• 2007

Round piles of Korean larch were excavated from the foundation of ex-Chosunchongdokbu (ex-Chosun Governer-General Building), which was constructed in 1916 and dismantled later in 1996. By the record (Huh, 1996), the Korean larch logs were logged from the Yalu river area near Mt. Baekdu in North Korea. At present, however, Korean larch is not so popular in South Korea. The latewood ratio profiles and strength properties (longitudinal compression, shear, longitudinal tensile, and bending) were obtained. The ratio of latewood from pith to bark increased up to 25 years, and then it showed constant tendency at 40% with some variances. From the microscopic observation, however, the latewood ratio decreased from the heartwood to the sapwood. Compression strength was greater and bending strength was a little lower than the previous reports (references 13~15), which might be attributed to the strength reduction of old structural members by aging or damage in the compression specimens than the bending ones. The flat-grained specimens for the shear and tension test showed higher coefficient of variation (COV) than the edge-grained ones. For the better comparison of results, in case of shear and tensile strength tests, the strength values of the edge-grained specimens were thought to be adopted rather than those of flat-grained ones.

• Journal of the Korea Furniture Society
• /
• v.11 no.2
• /
• pp.25-35
• /
• 2000

This study was carried out to investigate the wood properties for development the proper uses of lesser-known tree species. The tested species are Tamiang(Hydnocarpus woodii) Bangelem (Strombosia zeylanica) and Kamasulan(Anisophyllea ferruginea) grown in Indonesia. fundamental wood properties such as anatomical, physical and chemical properties and characteristics related to wood processing were examined. The results are summarized as follows : These species are diffuse porous, interlocked grained and coarse textured wood. Exceptionally, texture of Tamiang is fine. The heartwoods of these species are not distinguished clearly to the sapwoods. These species have high specific gravity, high shrinkage, and excellent strength properties. However, Tamiang has moderate specific gravity. Sawing characteristics are poor for these species except Tamiang. Sawing characteristics is moderate for Tamiang. Drying characteristics are moderate for Tamiang and Bangelem, and Poor for Kamasulan. The surfacing characteristics by planer are moderate f3r all these species. Bending property and durability are poor. Ash content is low in Bangelem.

• Journal of the Korea Furniture Society
• /
• v.11 no.1
• /
• pp.13-23
• /
• 2000

This study was carried out to investigate the wood properties for development the proper uses of lesser-known tree species. The tested species are Kebambang(Pentace sp.), Bawang-bawang(Dysoxylum alliaceum Bl .), Garu buaya( Gonystylus brunescens A. Shaw)grown in Indonesia. fundamental wood properties such as anatomical, physical, mechanical and chemical properties and characteristics related to wood processing were examined. The results are summarized as follows : The woods of these species are diffuse porous, coarse textured, and interlocked grained. The heartwood of Kebambang is distinguished clearly to the sapwood, but the heartwood of other species are not distinguished clearly to the softwood. The woods of Kebambang and Bawang-bawang have the moderate weight density and the low strength properties, but Garu buaya has the high weight density and the high strength properties. The woods of these species has high shrinkage. The sawing characteristics of Kebambang are excellent but the other species are moderate. The machining characteristics by planer and drying characteristics of these species are moderate. These woods has poor characteristics in bending processing and decay durability. The wood of Bawang-bawang has high content of the extractives and lignin.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.726-735
• /
• 2016

This study was carried out to evaluate the high-temperature drying characteristics of douglas-fir, hemlock, and radiata pine square timber with dimensions of thickness 15 cm and 18 cm. As a result, radiata pine showed the lowest final moisture content followed by douglas-fir and hemlock without reference to the timber size. Moreover, when the longitudinal kerfing is processed, the final moisture content was lower than control. The kerfing treatment was effective to decreasing the twist of radiata pine and hemlock. When douglas-fir is processed to the shape like the edge-grained timber that does not include the pith, the decrease of drying defect was possible.

• Journal of the Korea Furniture Society
• /
• v.18 no.1
• /
• pp.39-46
• /
• 2007

This study was carried out to investigate the wood properties for efficient utilization of warm temperate tree species of Quercus acuta Thunb. grown in Korea. Fundamental wood properties in the anatomical, physical, mechanical and chemical characteristics were examined. Quercus acuta Thunb. is a radial-porous, straight grained and fine textured wood. The heartwood is not clearly distinguished from the sapwood. In physical properties, it has a high oven-dry specific gravity of $0.85{\pm}0.02$, and high shrinkage from green to air-dried condition of $7.05{\pm}0.52%$ in radial and $11.13{\pm}0.48%$ in tangential direction. Mechanical properties determined are strong with the MOR of $1,065{\pm}90kgf/cm^2$, and tensile strength parallel to grain of $1,490{\pm}258kgf/cm^2$ and shear strength of $175{\pm}13kgf/cm^2$. Also, this wood has high extractive contents: 11.11% for cold and 13.51% for hot water.