• The Journal of the Acoustical Society of Korea
• /
• v.14 no.1
• /
• pp.73-80
• /
• 1995

In this paper, Polarity Thresholding(PT) algorithm has been studied to enhance the received signal in ultrasonic inspection of the stainless-steel(SUS 304) which is the primary piping material of a nuclear power plant. The spectral decomposition components obtained by splitting the spectrum of received signals are composed of dispersive signal of the interference pattern produced by the grain boundaries and nondispersive signal by the flaw. PT algorithm enhance the SNR of received signal by using above properties. In experiment the stainless-steel has been chosen as the sample and heat-treated at 1125, 1150, 1175, and $1200^\circ{C}$, respectively. And the flat-bottom hole type defects have been made artificially in samples. The pulse-echo signals from the sample by using ultrasonic transducer of center frequency 5 MHz have been processed by PT algorithm. It has been shown that PT algorithm enhanced the SNR by average 14.2 dB.

• The Research Journal of the Costume Culture
• /
• v.18 no.3
• /
• pp.465-475
• /
• 2010

For this study, 18 kinds of cut and sew or seamless knitted test garment were made. Samples differed from each other by skirt angles($90^{\circ}$, $180^{\circ}$), gauges(7G, 12G, 15G), and grain directions(bias direction, wale direction, and radial direction). After measuring the mechanical properties of various gauges on the seamless knitting machine, I compared shape of the knitted flare skirt through subjective evaluation on appearances. The data analysis methods used in this study were descriptive statistics, one-way ANOVA, Duncan-test, correlation analysis, and regression analysis. The subjective evaluation on appearances of knitted flare skirts showed the following: In case of $90^{\circ}$ skirt, the seamless skirt showed a much higher score in every gauge expect that of the cut and sew 12G, and silhouette of 15G wale direction. In case of the $180^{\circ}$ skirt, the seamless type showed a much higher score in every item over the cut and sew expect the silhouette part of 7G wale direction.

• Journal of the Korean Magnetics Society
• /
• v.4 no.2
• /
• pp.122-125
• /
• 1994

The magnetic properties of Nd-Fe-B alloys of containing 4 at.% Nd have been studied for the development of new type rare-earth magnets. The amorphous phase of a melt-spun $Nd_{4}Fe_{85.5}B_{10.5}$ alloy is transformed into the phases which have a small amount of $Nd_{2}Fe_{14}B_{1}$ in ${\alpha}-Fe$ matrix by annealing above their crystallization temperature. The addition of Mo, Nb, V or Cu to $Nd_{4}Fe_{85.5}B_{10.5}$ alloy results in the reduction of grain size and the sub¬sequent improvement of the coercivity. The coercivity of $Nd_{4}Fe_{82}B_{10}M_{3}Cu_{1}$(M = Mo, Nb, V) alloys increases in the order of M = V < Nb < Mo and shows the highest value of 2.7 kOe when M = Mo. On the other hand, the rem¬anence of these alloys shows the opposite trend and the rn>st improved value of 1.35 T is observed when M = V.

• Korean Journal of Agricultural Science
• /
• v.41 no.1
• /
• pp.1-7
• /
• 2014

Ratooning ability is one of the major different traits from perennial to cultivated rice and annual type. We developed a set of 126 introgression lines derived from a cross between Hwayeong and W1944 (O. rufipogon) to gain an insight into the genetic factors underlying differences between common wild rice and cultivated rice. One IL, CR6 among the 126 ILs of $BC_3F_4$ showed a significant difference in rationing ability compared with Hwayeong. To further characterize the rationing ability, CR6 was selected and crossed to Hwayeong to produce three secondary populations, $BC_4F_2$, $BC_4F_3$ and $BC_5F_2$. In the Hwayeong background, the W1944 allele was associated with an increase in rationing ability. QTL analysis showed that the qRAT5 for rationing ability was linked to RM194 ($R^2$=6.6%, 19.6%, and 44.5% in the $BC_4F_2$, $BC_5F_2$, and $BC_5F_3$, respectively). The putative qRAT5 was also tightly linked to QTLs for spikelets per panicle and grain weight indicating that this region harbors a QTL cluster related to domestication. To our knowledge, this is the first report to map the major QTL for ratooning ability in rice. The SSR markers linked to qRAT5 would be useful in marker-assisted selection for breeding lines with enhanced ratooning ability.

• Journal of Technologic Dentistry
• /
• v.36 no.1
• /
• pp.9-15
• /
• 2014

Purpose: Generally dental technicians clinically decide the sintering temperature of zirconia artificial teeth to match the color of the teeth. However, the sintering temperature influence the microstructure and mechanical strength of ceramic body. In this study, to evaluate the free choice of sintering temperature which leads to color the problems in zirconia false teeth, the variation of microstructure, mechanical strength, and colortone of zirconia ceramics according to the change of sintering temperature was investigated. Methods: Bar type specimens were prepared from commercial zirconia blocks by cutting and polishing into $0.8cm(L){\times}1.0cm(W){\times}4.8cm(H)$. Specimens were fired from 1,400 to $1,700^{\circ}C$ at $50^{\circ}C$ intervals and held for 1hour at highest temperature. Apparent porosity, water absorption, firing shrinkage, bulk density, bend strength, whiteness were tested. Microstructures were observed by SEM. Results: When fired above $1450^{\circ}C$, all specimens showed 0% apparent porosity and water absorption, 20% firing shrinkage, and $6.1g/cm^3$ bulk density regardless of firing temperatures. SEM photomicrographs showed grain growth of zirconia occurred above $1,600^{\circ}C$. Whiteness was also largely changed above this temperature. Maximum bend strength of 1,05MPa was obtained at $1,550^{\circ}C$. Bend strength lowered slightly above this temperature and showed $950{\ss}\acute{A}$ at $1,700^{\circ}C$. Conclusion: In order to fit the colortone of zirconia artificial teeth, arbitrary choice of firing temperature higher than $1,500^{\circ}C$, up to $1,700^{\circ}C$ did not influence the mechanical strength.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1118-1125
• /
• 2005

In this study, seismic safety of CFRD(Concrete-Face Rockfill Dam) type "D" dam in operation is evaluated from the results of 1-g shaking table test using similitude laws. Model dam is made by similitude law considering the grain size of prototype dam component. After the model dam is impounded to the normal water level(N.W.L), it is excited by artificial earthquake wave corresponding to standard design respond spectrum of the "D" dam site. Displacement response behavior of the dam is examined through the measurement of vertical and horizontal displacement of dam crest. Also, amplification characteristics of acceleration with dam height is examined through the measurement of acceleration with dam height. Finally, the purpose of this study is to evaluate seismic safety of "D" dam in operation. From the results of acceleration measurement, it was found that acceleration of dam crest was amplified about 1.52 times compared to the acceleration of dam bottom and amplification phenomenon is outstanding at three quarters of dam height from the bottom of dam. From the analysis of displacement behavior, it was estimated that vertical displacement of prototype dam is 6.8cm (0.1% of dam height) and horizontal displacement 12.3cm(0.2% of dam height). These percentages is much lower than 1% of dam height(general stability criteria). Therefore, it was concluded that seismic stability of "D" dam against an estimated earthquake is guaranteed.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.6
• /
• pp.670-677
• /
• 2012

Perovskite-type oxides such as doped barium zirconate ($BaZrO_3$) show high proton conductivity and chemical stability when they are exposed to hydrogen and water vapour containing atmospheres, thus it can be applicable to the hydrogen separation and the fuel cell electrolyte membranes. However the high temperature ($1700-1800^{\circ}C$) and long sintering times (24h) are generally required to prepare the fully densified $BaZrO_3$ pellets. These sintering conditions lead to the limitation of the grain size growth and the degradation of conductivity due to the acceleration of BaO evaporation at $1200^{\circ}C$. Here we demonstrate NiO-doped $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ with lower calcination and sintering temperature, less experimental procedure and lower process cost than the conventional mixing method. The stoichiometry of $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ was optimized by the control of excess amount of Ba (5mol%) to minimized BaO evaporation. We found that the crystal size of NiO-doped $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ was increased with increase of calcination temperature from XRD analysis. NiO-doped $BaZr_{0.85}Y_{0.15}O_{3-{\delta}}$ powder was calcined at $1000^{\circ}C$ for 12h when its showed the highest conductivity of $3.3{\times}10^{-2}s/cm$.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.40 no.3
• /
• pp.160-166
• /
• 2007

The coarse deposit with a lower mud content adjacent to the shelf of the southern East Sea is probably a "relict" sediment deposited in response to a lower stand of sea level during the Pleistocene. The sediment that developed on the slope and in the deep sea was river-borne primarily and was secondarily reworked or redistributed by the Tsushima Warm Current from the East China Sea. The clay mineralogy of the area suggests various sources of fine-grained sediment from adjacent rivers, the Korea Strait, volcanic material from Ulleung Island, and the Japan coast. Massive sand, bioturbated mud, homogeneous mud, and laminated mud were the dominant facies found in the core sediments from the study area. The massive sand was mainly volcanic ash from an eruption on Ulleung Island (9300 yr BP) and consisted of colorless pumiceous glass and a black scoriaceous type. The sedimentation rates on the slope, based on the Ulleung-Oki ash layer, were about 10cm/ky higher than in the basin. Other than the coarse-grain sediment, the mean size of the fine sediment dominating the bioturbated and homogeneous muds in the basin and the laminated mud on the slope was 6-10 phi. This indicates a difference in the major sedimentary process: hemipelagic sedimentation in the Ulleung Basin and mass flow deposition, such as turbidite, on the slope of the southern East Sea.

• The Plant Pathology Journal
• /
• v.34 no.5
• /
• pp.412-425
• /
• 2018

The Hfq protein is a global small RNA chaperone that interacts with regulatory bacterial small RNAs (sRNA) and plays a role in the post-transcriptional regulation of gene expression. The roles of Hfq in the virulence and pathogenicity of several infectious bacteria have been reported. This study was conducted to elucidate the functions of two hfq genes in Burkholderia glumae, a causal agent of rice grain rot. Therefore, mutant strains of the rice-pathogenic B. glumae BGR1, targeting each of the two hfq genes, as well as the double defective mutant were constructed and tested for several phenotypic characteristics. Bacterial swarming motility, toxoflavin production, virulence in rice, siderophore production, sensitivity to $H_2O_2$, and lipase production assays were conducted to compare the mutant strains with the wild-type B. glumae BGR1 and complementation strains. The hfq1 gene showed more influence on bacterial motility and toxoflavin production than the hfq2 gene. Both genes were involved in the full virulence of B. glumae in rice plants. Other biochemical characteristics such as siderophore production and sensitivity to $H_2O_2$ induced oxidative stress were also found to be regulated by the hfq1 gene. However, lipase activity was shown to be unassociated with both tested genes. To the best of our knowledge, this is the first study to elucidate the functions of two hfq genes in B. glumae. Identification of virulence-related factors in B. glumae will facilitate the development of efficient control measures.

• Journal of the korean society of oceanography
• /
• v.34 no.4
• /
• pp.220-230
• /
• 1999

Four tidal flats, covering two dissipative type beaches and two other tidal mud flats, around Yonaiong-Yongyu Islands, Inchon, Korea were studied in May 1991 to analyze the spatial distribution patterns of benthic communities on macrotidal flats. From the statistical test on spatial patterns of species number, density, and biomass, significant trends were found in species number and biomass. Although quantitative analysis was not performed, the interpretation showed that the variations were ruled out by environmental gradients such as sediment grain size and tidal elevation. The eight communities revealed in this study are as follows: Moerella-Mactra(Group 1), llyoplax-Glycera -Magelona japonica-Magelona sp.-Pe riserrula ( Group 2), Amphiura-Nephtys californiensis-Bullacta-Eohaustorius (Group 3), Leonnates-Heteromastus-Pretankyra-Nephtys polybranchia (Group4), Nephtys chemulpoensis-Macrophthalmus (Group 5), Ceratonereis-Scopimera (Group 6), Haustorioides-Urothoe (Group 7) and Cycladicama-Armandia-Minuspio community (Group 8). Some of these communities were classified into substratum-specific (Group 1 to 3) and tidal elevation-specific communities (Group 4). It was difficult to identify the predominant governing agent in Groups 5,6,7 and 8 because of their presence at extreme types of sediment and at uppermost elevations. Mixed effects seemed to act upon the latter four communities (Group 5 to 8). Based on the number of samples, 60% of the target samples were influenced by substratum properties, 20% by tidal elevation effect and 20% by mixed effect of the two factors. From this, it was concluded that substratum properties serve as the most important factors on soft bottom inhabitants in the area studied.