• Journal of the Korean Ceramic Society
• /
• v.29 no.4
• /
• pp.65-65
• /
• 1992

Role of CaO in the sintering of 12Ce-TZP ceramics was studied. The addition of small amounts of CaO increase the densification rate of 12Ce-TZP by altering lattice defect structure and the diffusion coefficient of the rate controlling species, namely cerium and zirconium cations. CaO also inhibits grain growth during sintering and allows the sintering process to proceed to theoretical density by maintaining a high diffusion flux of vacancies from the pores to the grain boundaries. The inhibition of grain growth is accomplished by the segregation of solute at the grain boundaries, causing a decrease in the grain boundary mobility. The segregation of calcium was revealed by AES study.

• Korean Journal of Materials Research
• /
• v.1 no.1
• /
• pp.37-45
• /
• 1991

In order to control the microstructures, the sintering behavior and abnormal grain growth with Ba/Ti ratio variation of $BaTiO_3$were investigated. The $BaTiO_3$powders used in this study were prepared by conventional calcination of $BaCO_3$ and $TiO_2$. The onset temperatures of the sintering were lowered and the densification was enhanced with increasing amounts of $TiO_2$ excess. These results are because of decrease of calcined particle sizes. A eutectic melt above temperature of $1320^{\circ}C$ did not assist the densification. Grain growth was strongly inhibited with increasing amounts of $TiO_2$ excess. The inhibition of grain growth caused abnormal grain growth due to inhomogeneous distribution of Ti-rich second phase.

• Journal of Powder Materials
• /
• v.12 no.1
• /
• pp.43-50
• /
• 2005

Mechanical alloying using high-energy ball mill and subsequent spark plasma sintering (SPS) process was applied to Al-Fe-Cr and Al-Fe-Mo powder mixture to investigate effects of Cr and Mo addition on thermal stability of Al-Fe, and thereby to enhance its thermal stability up to $500^{\circC}$. Various analytical techniques including micro-Vickers hardness test, SEM, TEM, X-ray diffractometry and corrosion test were carried out. It was found that addition of Cr and Mo to Al-Fe system played a role of grain growth inhibitor of matrix Al and some precipitates such as $Al_3Fe$ during SPS and subsequent heat treatment. The inhibition of grain growth resulted in increased Vickers hardness and thermal stability up to $500^{\circC}$ comparing to those of Al-Fe alloy system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.326-329
• /
• 1996

In order to synthesize Ba-ferrite fine particles by molten salt method and inhibit the abnormal grain growth of sintered specimen, KCI anti NaCl were added to basic composition to 50% by weight, and added 1 male% of $SiO_2$ to control the shape of Ba-ferrite particles. $H_{c}$ and $M_{r}$ were decreased when F $e^{3+}$ was substituted with $Co_{2+}$ and $Ti_{4+}$ from x=0 to x=1.0 in $BaFe_{12-2x}$ $Ti_{x}$ $Co_{x}$ $O_{19}$ , and 1 mole% $SiO_2$ increased the size but shortened c-axis of hexagonal ferrite. Seeds added in Ba-ferrite particle effected inhibition of abnormal grain growth during sintering.ing.g.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.207-207
• /
• 2017

The proso millet is vulnerable to lodging due to high plant height and shallow root. A lodging results in a hard mechanical harvesting and yield loss. One of solutions on this problem is inhibition of internode elongation. The objective of this study was to set up use time and dose of prohexadium-calcium, is growth inhibitor. The experimental variety was Ibaekchal. The experiment design was a split-plot design with three replications. The treatments were as follow: Main-plots were 25 and 35 day after sowing(DAS) as use time and sub-plots were 0%, 50%, 100%(diluted solution of 1000 times, $1000{\ell}\;ha^{-1}$), 150% as dose. The amount of nitrogen, phosphate and potassium fertilization were 90, 70, $80kg\;ha^{-1}$, respectively. The size of high ridge and plant spacing were $90{\times}30cm$ and $60{\times}15cm$, respectively. Proso millet was sown on June 9, 2016 by hands and was adjusted at 2 plant per hill. The growth survey of vegetative growth stage was conducted at 1 day before treatment and with one week interval after treatment. Data were collected: (1) grain yield: weight of grain in $kg\;ha^{-1}$, (2) 1000 grain weight: average weight of 1000 grain, (3) plant height: distance from soil to top of panicle or leaf in cm, (4) ear length: distance from top of stem to top of ear in cm, (5) stem diameter: diameter of second internode (6) degree of lodging: percentage of lodging area, etc. Analyses of variance were performed using R version 3.3.1(https://www. r- project. org). The Duncan's multiple range test(DMR) was used to separate treatment means at P < 0.05. There was a significant difference in plant height and number of stem among the use time and dose of prohexadium-calcium during vegetative growth stage. At 25 DAS, the difference with no treatment increased until 25 day after treatment and decreased since then. The difference in number of stem increased until 18 day and decreased since 25 day. At 35 DAS, the difference with no treatment in plant height and number of stem increased until 22 day after treatment and decreased since then. We assumed that the effect of prohexadium-calcium was inhibition of internode elongation and promotion of tillering, continued untel 25day after treatment. At 25 DAS, the degree of lodging deceased to 100%, 30%, 10% and 0% as dose increased. At 35 DAS, the degree of lodging decreased to 100%, 20%, 0% and 0% as dose increased. At 25 DAS, the yield was 2910, 2710, 3190, $2310kg\;ha^{-1}$ among dose. At 35 DAS, the yield was 2750, 2630, 2220, $2050kg\;ha^{-1}$. We recommend that the optimum use time and dose of prohexadium-calcium for proso millet is 1000 times diluted solution of $1000{\ell}$ per ha at 25 day after sowing.

• Journal of Korea Foundry Society
• /
• v.31 no.6
• /
• pp.347-353
• /
• 2011

There is thixo-extrusion to form high strength aluminum alloy. But, it is a problem that grains become grain coarsening during reheating process because the alloy was exposed at high temperature. In order to solve grain growth during reheating process, calcium was added in Al-Zn-Mg alloys. Primary a grain sizes of semi-solid Al-Zn-Mg-(0, 0.4, 0.6 and 0.9, wt.%)Ca were measured with image analyzer after reheating. Measured primary a grain sizes were applied to LSW(Lifshitz-Slyozov and Wagner) equation to check the effect of Ca on grain coarsening. Coarsening rate constant K values of semi-solid Al-Zn-Mg-(0, 0.4, 0.6 and 0.9, wt.%)Ca alloys were $371\;mm^3s^{-1}$, $247\;mm^3s^{-1}$, $198\;mm^3s^{-1}$ and $166 mm^3s^{-1}$, respectively. As increasing calcium content, K value decreased which means grains are refined. Also, grains of calcium addition were more spherical than that of calcium free.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.29 no.3
• /
• pp.285-290
• /
• 1984

The effects of retardants B995 and CCC on the growth and yield of soybean cultivar, kwanggyo, were investigated. The 3 application times(4th, 5th and 6th trifoliate leaf stage) combined with 4 concentrations (500, 1000, 2000 and 3000 ppm) were treated, and the retardant solutions were sprayed on the foliage. Only stem length in retardants, rate of podding in application times, and, in concentrations, stem length, number of branch, number of pod per plant and grain yield, were significant. In the inhibition of stem elongation, B995 was more effective than CCC, and rate of podding was the highest in the 4th leaf-spraying. The highest concentration, 3000 ppm, was the most effective in the inhibition of stem elongation and in the increase of number of branch and pod, rate of podding, and in yield. The number of node of mainstem, dry stem weight, chlorophyll and 100 grain weight were not significant with any treat. Yield had positively correlated with number of branch and pod, and rate of podding but negatively with stem length. The retardants was thought to be considerably conducive to the increase of yield.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.4
• /
• pp.172-179
• /
• 2006

When $Al_2O_3-MoO_3$ mixture is reduced, $MoO_3$ is only reduced to Mo at $900^{\circ}C$. But a compound between $Al_2O_3$ and Mo is not formed up to $1300^{\circ}C$. In the case of $Al_2O_3-MoO_3-MnO_2$ mixture, an intermediate compound $Mn_2Mo_3O_8$ is firstly formed at $900^{\circ}C$ and changes to $MnAl_2O_4$ at $1100^{\circ}C{\sim}1300^{\circ}C$. $Al_2O_3/Mo/MnO_2$ composite are manufactured by a selective reduction process in which Mo is only reduced in the powder mixture of $Al_2O_3,\;MoO_3\;and\;MnO_2$ oxide. For $Al_2O_3/Mo$ composite, the average grain size was not changed with increasing Mo content because of inhibition of grain growth of $Al_2O_3$ matrix in the presence of Mo particles. Fracture strength increased with increasing Mo content due to phenomenon of grain growth inhibition of $Al_2O_3$ matrix. Hardness decreased because of a lower hardness value of Mo, whereas fracture toughness increased. For $Al_2O_3,\;Mo\;and\;MnO_2$ composite, grain growth was facilitated by MnOB and it showed a lower fracture strength because of grain growth effect with increasing Mo and $MnO_2$ content. Hardness decreased because of the grain growth of matrix and coalesced Mo particles to be located in grain boundary, whereas fracture toughness increased.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.4
• /
• pp.144-148
• /
• 2005

The microstructure and electrical properties of varistor ceramics, which are composed of Zn-Pr­Co-Cr-Dy-oxide system, were investigated at various dysprosia $(Dy_2O_3)$ addition contents. The $DY_2O_3$ microstructurally played the role of inhibition for the densification and grain growth. As the $DY_2O_3$ content increased, the density decreased in the range of $5.51-4.90 g/cm^3$, reaching maximum at $0.5 mol\%$ and the average ZnO grain size decreased in the range of $17.7-6.0{\mu}m$. The incorporation of $DY_2O_3$ significantly improved the nonlinear properties of varistors, above 30 in nonlinear exponent, compared with that without $DY_2O_3$. The varistors with the best performance of nonlinear properties was obtained $DY_2O_3$ content of $1.0 mol\%$, 49 in nonlinear exponent and $0.5{\mu}A$ in leakage current.

• Journal of the Korean Ceramic Society
• /
• v.33 no.1
• /
• pp.83-91
• /
• 1996

Monolithic AlN and AlN-W composites were fabricated by pressure-less sintering at 190$0^{\circ}C$ under nitrogen atmosphere and the influences of tungsten phase on the microstructure and mechanical properties were investi-gated. In the fabrication of sintered specimen no additive was used. And monolithic AlN showed substantial grain growth and low relative density. AlN-W composites were fully densified and grain growths of matrix were inhibited. The densification behavior of composites were inferred to be achieved through the liquid phase sintering process such as particle-rearrangement and solutino-reprecipitation. Also the oxid phases which is expected to form liquid phases duringsintering process were detected by XRD analysis. As the tungsten volume content increases fracture strength was decreased and fracture toughness was increased. It was suppo-sed that the strength decrease of composites with tungsten content was due to existence of interface phases. The subcritical crack growth behavior was observed from the stress-strain curve of composites. The effect of the secondary phase and interface phases on toughness in crease were studied through observation of crack propagation path and the influence of residual stress on crack propagation was investigated by X-ray residual stress measurement. In the result of residual stress measurement the compressive stress of matrix in composi-test was increased with tungsten volume content and the compressive stress distribution of matrix must have contributed to the inhibition of crack propagation.