• Transactions of Materials Processing
• /
• v.11 no.6
• /
• pp.519-528
• /
• 2002

The microstructural evolution during the equal channel angular pressing of Ti-6Al-4V alloy was investigated using the transmission electron microscopy (TEM). ECA pressing was carried out isothermally with route C at $600^{\circ}C$ for two types of initial microstructure, i.e., equiaxed and Widmanstatten microstructures. At an initial stage of ECA pressing, the equiaxed microstructure showed more uniform flow than the Widmanstatten microstructure. However, both microstructures were significantly refined revealing nearly equiaxed grains of 0.3$mu extrm{m}$ in diameter with high angle grain boundaries after 4 passes of ECA pressing. These ultrafine gains were found to be stable with little grain growth, when annealed up to $600^{\circ}C$ for 1hr.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.32-32
• /
• 2017

To increase rice production, manipulating plant architecture, especially developing new high-yielding cultivars with erect leaves, is crucial in rice breeding programs. Leaf inclination angle determines the light extinction coefficient (k) of the canopy. Erect leaves increase light penetration into the canopy and enable dense plantings with a high leaf area index, thus increasing biomass production and grain yield. Because of erect leaves, the high-yielding indica rice cultivar 'Takanari' has smaller k during ripening than 'Koshihikari', a japonica cultivar with good eating quality. In our previous study, using chromosome segment substitution lines (CSSLs) derived from a cross between 'Takanari' and 'Koshihikari', we detected seven quantitative trait loci (QTLs) for leaf inclination angle on chromosomes 1 (two QTLs), 2, 3, 4, 7, and 12. In this study, we developed a near-isogenic line (NIL-3) carrying a 'Takanari' allele for increased leaf inclination angle on chromosome 3 in the 'Koshihikari' genetic background. We compared k, dry matter production, and grain yield of NIL-3 with those of 'Koshihikari' in the field from 2013 to 2016. NIL-3 had higher inclination angles of the flag, second, and third leaves at full heading and 3 (- 4) weeks after full heading and smaller k of the canopy at the ripening stage. Biomass at full heading and leaf area index at full heading and at harvest did not significantly differ between NIL-3 and 'Koshihikari'. However, biomass at harvest was significantly greater in NIL-3 than in 'Koshihikari' due to a higher net assimilation rate at the ripening stage. The photosynthetic rates of the flag and third leaves did not differ between NIL-3 and Koshihikari at ripening. Grain yield was higher in NIL-3 than 'Koshihikari'. Higher panicle number per square meter in NIL-3 contributed to the higher grain yield of NIL-3. We conclude that the QTL on chromosome 3 increases dry matter and grain production in rice by increasing leaf inclination angle.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.5
• /
• pp.440-444
• /
• 2006

This study was carried out to compare the grain quality under lodging time and grade at ripening. Ripened grain ratio and 1000-grain weight were higher with lodging of plants at $45^{\circ}$ angle from the ground and increased with crop development. The number of spikelets, as well as the protein and amylose content of the grains, were higher in plants under severe or complete lodging than those under lodging at $45^{\circ}$ angle from the ground. Palatability and sensory evaluation values were higher in plants under lodging at $45^{\circ}C$ angle from the ground than those under complete lodging. Brown rice: rough rice ratio was higher with lodging of plants at $45^{\circ}C$ angle from the ground and increased with crop growth. Milling recovery and milled rice recovery were higher with lodging of plants at $45^{\circ}C$ angle from the ground, whereas chalky grain, cracked grain and damage grains were higher at complete lodging.

• Journal of Powder Materials
• /
• v.17 no.1
• /
• pp.52-58
• /
• 2010

Bulk nanostructured metallic materials are generally synthesized by bottom-up processing which starts from powders for assembling bulk materials. In this study, the bottom-up powder metallurgy and High Pressure Torsion (HPT) approaches were combined to achieve both full density and grain refinement at the same time. After the HPT process at 473K, the disk samples reached a steady state condition when the microstructure and properties no longer evolve, and equilibrium boundaries with high angle grain boundaries (HAGBs) were dominant. The well dispersed alumina particles played important role of obstacles to dislocation glide and to grain growth, and thus, reduced the grain size at elevated temperature. The small grain size with HAGBs resulted in high strength and good ductility.

• Geomechanics and Engineering
• /
• v.35 no.2
• /
• pp.135-147
• /
• 2023

Sand columns in clayey soil are considered one of the most economical and environmentally-friendly soil-improving techniques. It improves the shear strength parameters, reduces the settlement, and increases the bearing capacity of clayey soils. The aim of this paper is to study the effect of grain shape in sand columns on their performance in improving the mechanical properties of clayey soils. An intensive series of consolidated-drained triaxial tests were performed on clay specimens only and clay specimens with sand columns. The parameters examined during the experimental work were grain shape in sand columns (angular, rounded, sub-rounded) and effective confining pressure (50 kPa, 100 kPa, 200 kPa). The results indicated that there is a significant improvement in the deviatoric stress and stiffness values of specimens with sand columns. Improving deviatoric stress values in the use of angular sand grains was found to be higher than those in the use of sub-rounded and rounded sand grains. A 187%, 159%, and 153% increment in deviatoric stress values were observed for the sand columns with angular, sub-rounded, and rounded grain shapes, respectively. The specimens were observed to be more contractive as the sand column was installed, and as the angularity of grains in the sand column was increased. Sand column installation improves significantly the angle of internal friction, and the effective angle of internal friction increases as the angularity of the sand grains increases.

• Journal of Industrial Technology
• /
• v.22 no.A
• /
• pp.153-159
• /
• 2002

This paper is an experimental work of estimating friction angle of very coarse grained soil such as rubble mound by performing laboratory experiments. Two crushed rocks of rubble mound were used for tests. Triaxial compression tests with drained conditions were performed to measure friction angles of soils prepared by mixing the crushed soil having an identical coefficient of uniformity with different maximum grain size distribution. Centrifuge model experiments with those soils were also performed to measure angle of repose and to estimate friction angle of soil from measuring the slope of slip line in the active stress state. Model tests were carried out by changing the G-levels of 1G and 50G. From triaxial compression tests, the measured value of friction angle of soil is in the range of $41{\sim}57^{\circ}$. The measured value of repose angle is in the range of $32{\sim}35^{\circ}$. The values of friction angle are found not so sensitive to the maximum grain size of soil as long as the coefficient of uniformity is identical. Estimated value of friction angle from measuring the slope of slip line in the active stress state is in the range of $30{\sim}46^{\circ}$. Thus, the estimated angle of friction are found to be greater in the order of the measured angle of repose, the estimated value from the slope of active state, and triaxial compression test results. On the other hand, the measured values of friction angle from triaxial tests were compared with empirical equations, based on the relation between friction angle and void ratio. Equations proposed by Helenelund(l966) and Hansen(1967) found to be relatively reliable to estimate friction angles of soil.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.177-180
• /
• 2002

The effects of pressing temperatures on the formability and the microstructural evolution during equal channel angular pressing (ECAP) of lamellar Ti-6Al-4V alloy were investigated in this study. ECAP above isothermally 600$^{\circ}C$ was successful without producing any noticeable segments at the specimen surfaces after a single pass of pressing. After 4 passes of ECA pressing, lamellar microstructures were significantly refined revealing equiaxed grains of 0.3$\mu\textrm{m}$ in diameter consisting of high angle grain boundaries. Also these ultrafine grains were relatively stable with little grain growth when annealed up to 600$^{\circ}C$ for 1hour.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.4
• /
• pp.353-358
• /
• 1994

Grain yields of errect-leaved corn hybrids were reported to be increased as planting density(PD) increased compared to those of horizontal leaf type hybrids. This trial was conducted to investigate the difference between errect and horizontal-leaved hybrids in response to different PD. Grain yields of both type hybrids were decreased at the highest PD, however, that of horizontal-leaved hybrid, Ga209 ${\times}$ Ki14A, was decreased more than errect-leaved hybrids which indicated varietal difference in response to PD. Responses to PD for days to tasseling, plant height, ear height, and leaf angle were not significant, also, PD ${\times}$ hybrid interactions were not observed. Yield components were decreased as PD increased and there were no PD ${\times}$ hybrid interactions for these characters. Leaf angle was negatively correlated with grain yield and yield components except for kernel weight.

• Journal of the Korean Ceramic Society
• /
• v.38 no.10
• /
• pp.914-920
• /
• 2001

The grain orientation distribution and grain boundary characterization of $ZrB_2$-ZrC composites sintered by a SPS(Spark Plasma Sintering) method, a new sintering technique were analyzed by the EBSP technique and then their crystallographic results have been compared with those of a sintered specimen using a PLS(Pressureless Sintering) method. In the $ZrB_2$-ZrC composite manufactured by SPS, (0001) planes of $ZrB_2$ were oriented in the direction normal to the specimen surface. In the case of PLS, those of $ZrB_2$ were oriented normal to the electron beam. In both cases of PLS and SPS, ZrC grains had the randomly oriented grain structure. The grain boundary characterization showed that low angle grain boundaries in the PLS and SPS processed materials constituted about 10% and 8% of the total number of boundaries, respectively, represented the only slight difference between the proportion of low angle grain boundary. However, in the distribution of CSL(Coincident Site Lattice) boundaries, it was shown the higher proportion of CSL boundaries with $\Sigma$ 3,5,7,9, 11 in the SPS processed material.

• Geomechanics and Engineering
• /
• v.22 no.2
• /
• pp.165-171
• /
• 2020

Laboratory determination of strength and deformation behavior of clean sands and gravels has always been challenging due to the difficulty in obtaining their undisturbed samples. An alternative solution to this problem is to develop correlations between mechanical properties of cohesionless soils and their gradation characteristics. This study presents database of 3 natural sands with 11 varying particle size gradation curves to allow investigating relationships between mean particle size, maximum and minimum void ratio, relative density and shear strength of the test soils. Direct shear tests were performed at relative densities of 50, 75 and 95% to explore the effects of gradation and density on the angle of internal friction of the modeled sand samples. It is found that the mean grain size D₅₀ bears good correlations with void ratio range (e_max - e_min) and peak angle of internal friction 𝜙'_peak. The generated regression models are in good agreement with published literature and can be considered as reliable for natural sands in Pakistan. These empirical correlations can save considerable time and efforts involved in laboratory and field testing.