• 한국측량학회지
• /
• 제33권5호
• /
• pp.453-461
• /
• 2015

이 연구에서는 시공 중에 있는 곡선형 PCT 거더교의 처짐 관리를 위해 압출 시 예상되는 취약부위에 GPS를 설치하고 시공단계에 따라 처짐변위를 측정하였으며 응력, 온도 및 경사변위를 측정하여 GPS 관측데이터와 처짐변위와 비교하였다. 압출거리에 따른 GPS 실측값과 유한요소 모델링 해석값을 비교 분석한 결과, 실측값이 해석값에 비해 0.6∼1.6배 정도 차이가 발생하였으나, 온도를 보정함으로써 그 차이가 크게 감소하였다. 교량 거동 형상 분석 결과, 시공중 거동은 95m 지점과 75m 지점에서 노즈 선단부에 처짐이 발생하는 것을 확인하였으며 압축 취약부는 압축, 인장취약부는 인장력이 발생하였다. 연구결과, GPS 적용함으로써 시공 중 곡선형 PCT 거더교의 처짐 관리를 보다 효율적으로 가능할 것으로 판단되며, 향후 동일 공법의 교량을 시공할 시 향후 거동을 예측하고 관리하는데 도움을 줄 것으로 판단된다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 봄 학술발표회 논문집
• /
• pp.128-136
• /
• 2001

This paper presents an optimum deck and girder system design for minimizing the life-cycle cost (LU) of steel box girder bridges. The problem of optimum LCC design of steel box girder bridges is formulated as that of minimization of the expected total LCC that consists of initial cost, maintenance cost, expected retrofit costs for strength, deflection, and crack. To demonstrate the effect of LCC optimum design of steel box girder bridges, the LCC optimum design is compared with conventional design method for steel box girder bridges design. From the numerical investigations, it may be positively stated that the optimum design of steel box girder bridges based on LCC will lead to more rational, economical and safer design.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.125-130
• /
• 2001

A existing design method of PSC girder bridges, according to total service loads, stress required tendon force at a time. Because this design method increases beam depth, design of long span is difficult. However, As UC girder stressing at difficult loading stages reduces sectional depth of PSC girder, both design and operation of long span bridges is possible. so, this study analyzes the effect of design parameter (Girder Strength, Girder Spacing, Span Length, Joint Strength) on the beam depth of IPC girder continuous bridges, and shows sectional depth of UC girder for design of long span bridges. According to analysis, when a continuous bridges of same length span is at strength of joint over strength of girder of 600kg/$cm^{2}$, a change of beam depth is observed and when a continuous bridges of different span length is at strength of joint below strength of girder of 600kg/$cm^{2}$, a change of beam depth is observed. In two case, a change of beam depth is mostly observed over strength of girder of 350kg/$cm^{2}$ according to analysis of deflection data, a continuous bridges of IPC girder is nearly satisfied.

• Smart Structures and Systems
• /
• 제15권3호
• /
• pp.505-522
• /
• 2015

Variation of temperature is a primary environmental factor that affects the behavior of structures. Therefore, understanding the mechanisms of normal temperature-induced variations of structural behavior would help in distinguishing them from anomalies. In this study, we used the structural health monitoring data of the Shanghai Yangtze River Bridge, a steel girder cable-stayed bridge, to investigate the mechanisms of thermally induced vertical deflection ($D_T$) at mid-span of such bridges. The $D_T$ results from a multisource combination of thermal expansion effects of the cable temperature ($T_{Cab}$), girder temperature ($T_{Gir}$), girder differential temperature ($T_{Dif}$), and tower temperature ($T_{Tow}$). It could be approximated by multiple linear superpositions under operational conditions. The sensitivities of $D_T$ of the Shanghai Yangtze River Bridge to the above temperatures were in the following order: $T_{Cab}$ > $T_{Gir}$ > $T_{Tow}$ > $T_{Dif}$. However, the direction of the effect of $T_{Cab}$ was observed to be opposite to that of the other three temperatures, and the magnitudes of the effects of $T_{Cab}$ and $T_{Gir}$ were found to be almost one order greater than those of $T_{Dif}$ and $T_{Tow}$. The mechanisms of the thermally induced vertical deflection variation at mid-span of a cable-stayed bridge as well as the analytical methodology adopted in this study could be applicable for other long-span cable-stayed bridges.

• 한국재난정보학회 논문집
• /
• 제19권4호
• /
• pp.851-858
• /
• 2023

연구목적: 종래의 PSC 거더에 비해 단면 효율이 개선된 양각 거더교의 구조적 안전성을 확보하기 위한 연구를 수행하였다. 이를 위해 거더 길이, 높이, 폭과 같은 단면의 제원을 정하고 강연선의 배치를 설계하여 정적 및 동적 하중에 의한 양각 거더의 실질적인 성능을 검증하였다. 연구방법: 정적 성능 실험은 1차 및 2차 정적 하중에 대한 처짐, 균열 등의 거동 응답을 측정하여 사용성 한계상태를 검토하였다. 또한, 동적 하중 재하 실험은 시간에 따른 가속도, 변위 거동 응답을 측정하여 고유진동수 및 감쇠비를 산정하여 사용성 한계상태를 검토하였다. 연구결과: 정적 성능 실험 결과 최대 재하하중 기준 처짐값은 안정적인 거동을 나타났고, 최대 재하하중 수준에서 측정된 균열폭은 매우 작아서 사용성 한계상태를 만족하는 것으로 나타났다. 또한, 동적 하중 재하 실험 설계 시 산정된 고유진동수를 상회하는 고유진동수가 나타났으며, 현행 규정에 만족하는 감쇠비를 확보하는 것으로 나타났다.

• Steel and Composite Structures
• /
• 제13권3호
• /
• pp.239-258
• /
• 2012

In this paper, experimental investigations on high strength steel (HSS) stud connected steel-concrete composite (SCC) girders to understand the effect of shear connector density on their flexural behaviour is presented. SCC girder specimens were designed for three different shear capacities (100%, 85%, and 70%), by varying the number of stud connectors in the shear span. Three SCC girder specimens were tested under monotonic/quasi-static loading, while three similar girder specimens were subjected to non-reversal cyclic loading under simply supported end conditions. Details of casting the specimens, experimental set-up, and method of testing, instrumentation for the measurement of deflection, interface-slip and strain are discussed. It is found that SCC girder specimen designed for full shear capacity exhibits interface slip for loads beyond 25% of the ultimate load capacity. Specimens with lesser degree of shear connection show lower values of load at initiation of slip. Very good ductility is exhibited by all the HSS stud connected SCC girder specimens. It is observed that the ultimate moment of resistance as well as ductility gets reduced for HSS stud connected SCC girder with reduction in stud shear connector density. Efficiency factor indicating the effectiveness of high strength stud connectors in resisting interface forces is estimated to be 0.8 from the analysis. Failure mode is primarily flexure with fracturing of stud connectors and characterised by flexural cracking and crushing of concrete at top in the pure bending region. Local buckling in the top flange of steel beam was also observed at the loads near to failure, which is influenced by spacing of studs and top flange thickness of rolled steel section. One of the recommendations is that the ultimate load capacity can be limited to 1.5 times the plastic moment capacity of the section such that the post peak load reduction is kept within limits. Load-deflection behaviour for monotonic tests compared well with the envelope of load-deflection curves for cyclic tests. It is concluded from the experimental investigations that use of HSS studs will reduce their numbers for given loading, which is advantageous in case of long spans. Buckling of top flange of rolled section is observed at failure stage. Provision of lips in the top flange is suggested to avoid this buckling. This is possible in case of longer spans, where normally built-up sections are used.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(II)
• /
• pp.596-601
• /
• 2003

After the development of practical technology for tilting system, tilting trains are operated on conventional lines of KORAIL. As the running speed of trains is increased, it is very important to investigate the dynamic characteristics of plate girder bridges with direct track fixation. Therefore, this paper reviews the dynamic interactions between tilting train and welded plate girder bridges designed by L-22, a standard load type of KORAIL. The span lengths of plate girder analyzed here are 6.6m, 9.7m, 12.9m, 16.0m, 19.2m, 22.3m, 25.4m and 31.1m. Using 2-D dynamic analysis, the critical velocity of tilting train, vertical deflection ratios of plate girder and maximum accelerations of car body are calculated. And the analytical results are compared with those of design criteria.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1999년도 봄 학술발표회 논문집
• /
• pp.313-321
• /
• 1999

To design steel box girder bridge, designers have taken the classical load distribution coefficient methods. Due to the rapidly developing computer technique, steel box girder bridge is simply modeled as grillage method for analyzing the girder, or as fully finite element method for more accurate and detailed analysis. Recently, cruciform space frame method is developed for modeling and analyzing it more simply and easily compared with finite element method. So, this study for the examination of upper methods' characteristics loaded unit moment load and analyzed the distortional deflection with shell element method and cruciform space frame method, and for three span three girder steel box bridge, loading DB-24 loads, analyzed it by upper methods and compared the results.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(II)
• /
• pp.1047-1052
• /
• 2002

KTX is going to directly operate on the existing plate girder bridges before the complete construction of new high-speed line. Also the speed and traffic volume is increased after electrification of conventional line. Then, it is necessary to check the dynamic behaviors of these bridges. Therefore, this paper reviews the dynamic behaviors of welded plate girder bridges designed by L-22, a standard load type of KNR. The span lengths of plate girder analyzed here are 6.6m, 9.7m, 12.9m, 16.0m, 19.2m, 22.3m, 25.4m and 31.1m. Using 2-D dynamic analysis, vertical deflection ratios of plate girder and maximum accelerations of car body are calculated. And the analytical results are compared with those of design criteria.

• Steel and Composite Structures
• /
• 제22권6호
• /
• pp.1465-1486
• /
• 2016

Conventional plate I-girders are sensitive to local buckling of the web when they are subjected mainly to shear action because the slenderness of the web in out-of-plane direction is much bigger. The local buckling of the web can also cause the distorsion of the plate flange under compression as a thin-walled plate has very low torsional stiffness due to its open section. A new I-girder consisted of corrugated web, a concrete-filled rectangular tubular flange under compression and a plate flange under tension is presented to improve its resistance to local buckling of the web and distorsion of the flat plate flange under compression. Experimental tests on a conventional plate I-girder and a new presented I-girder are conducted to study the failure process and the failure mechanisms of the two specimens. Strain developments at some critical positions, load-lateral displacement curves, and load-deflection curves of the two specimens have all be measured and analyzed. Based on these results, the failure mechanisms of the two kinds of I-girders are discussed.