• Journal of the Korean Geotechnical Society
• /
• v.18 no.2
• /
• pp.13-21
• /
• 2002

A new method called S-SRICOS is proposed to predict the local scour depth around bridge piers. The S-SRICOS method is a simplified version of the SRICOS method which was developed to predict the scour depth versus time curve around bridge piers. The SRICOS method which considers the time effect based on the soil properties and the hydraulic parameters can handle a multi-flood hydrograph and multi-layer soil systems with the SRICOS program. An attempt was made to simplify the method to the point where only hand calculations would be required. The concept of the equivalent time was developed leer this purpose. The S-SROICOS method requires only 4 parameters such as pier width, design bridge life, design velocity corresponding to the design bridge life, and initial scour rate of the soil. The S-SRICOS method was verified against 55 cases of the scour depth results using the SRICOS method.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.571-578
• /
• 2009

Recently, micropiling techniques are increasingly applied in foundation rehabilitation/underpinning and seismic retrofitting projects where working space provides the limited access for conventional piling methods. Micropiling techniques provide environmental-friendly methods for minimizing disturbance to adjacent structures, ground, and the environment. Its installation is possible in restrictive area and general ground conditions. The cardinal features that the installation procedures cause minimal vibration and noise and require very low ceiling height make the micropiling methods to be commonly used for underpin existing structures. In the design point of view, the current practice obligates the bearing capacity of micropile to be obtained from skin friction of only rock-socketing area, in which it implies the frictional resistance of upper soil layer is ignored in the design process. In this paper, a new micropiling method and its verification studies via field installation are presented. The new method provides a specific way to grout bore-hole to increase frictional resistance between surrounding soil and pile-structure and it allows to consider the skin friction of micropiles for upper soil layer during design process.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.8
• /
• pp.5-11
• /
• 2014

The objective of this paper is to develop a rational reliability analysis procedure for the LRFD design provisions of bridge substructures. A bridge abutments is considered in this study. The reliability analysis is applied to determine the relationship between the major design parameters for bridge abutment and reliability index. The considered load components include dead load, vertical and horizontal earth pressure, earth surcharge, and vehicle live load. Several limit states are considered: foundation bearing capacity, sliding, and overturning. The analysis results show that the most important parameter in the reliability analysis is the effective stress friction angle of the soil. The reliability indices are calculated using Monte Carlo simulations for a selected bridge abutment. The results of the sensitivity analysis indicate that reliability index is most sensitive with regard to resistance factor and horizontal earth pressure factor.

• Geotechnical Engineering
• /
• v.5 no.4
• /
• pp.17-26
• /
• 1989

The creep ratio, which has been applied as a measure to prevent piping failure in designing embankments, has been originally proposed for the protection of masonry or concrete dam from piping along the boundary surface between the foundation soil and the bottom of the structure. In this study, it has been investigated whether this creep ratio could be applied for the earth embankment through the model test and we reevaluated the required creep ratio in the present design criteria. Based on this research, it was concluded that a piping failure would always occur within the embankment body and not through the boundary surface between the embankment and foundation. Therefore it could be said that the present design criteria are illogical to determine the design creep ratio according to less permeable soil no matter whether the soil forms embankment or foundation.

• Geotechnical Engineering
• /
• v.5 no.1
• /
• pp.19-26
• /
• 1989

In this study, the finite element method for nonlinear problems is developed theroretically to see the design loads of foundation, when the circular plate resting on elasto-viscoplastic soil medium is loaded axisymmetrically. The paper shows that the plastic zone of soil medium is displayed at the near the edge of plate at the first place; when the plastic zone of soil medium is linked around central axis, the external load is termed by allowable load or design load, and then the contact pressure changes abruptly, in this case it is approved to be the risk of shear failure. The results of numerical analysis using the Mohr-Coulomb yield criterion, and experimental analysis for a appropriate safety factor are approximative, but numerical results are smaller than the value based on Terzaghi's theory.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.11a
• /
• pp.140-167
• /
• 2002

A drilled shaft is a deep foundation that is constructed by placing fluid concrete in a drilled hole. Reinforcing steel can be installed in the excavation, if desired, prior to placing the concrete. Drilled shafts provide excellent foundation systems for civil structures. In order to utilize them effectively, it is essential that designers have a clear understanding for how drilled shafts are constructed and also understand the basis for design methods. This paper describes standard design methods for drilled shafts.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.407-414
• /
• 1999

A simple seismic design procedure for pile foundation using PAR and LPILE$\^$plus/ was proposed. A case of pile foundation under a simple bridge was selected and analyzed. The calculated horizontal movements, shear forces and moments were compared with those evaluated by the numerical exact solutions, and the farmers had similar trends with the tatters.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1993.10b
• /
• pp.51-76
• /
• 1993

More than sixty percentages of tunnels in the second phase of Seoul subway project have the ground coverages less than twenty meters. Majority of ground conditions encountered during turutel ling, therefore, are weathered rocks or weathered scils. Substantial lengths of tunnels are being constructed and designed running through the alluvial deposits as well. A comprehensive evaluation of current design and construction technology of Seoul subway tunnels is made with four categories such as site investigations, design concepts and methods, auxiliary measures and quality controls. Critical comments are given and some suggestions for the improvement of technology are presented.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.2
• /
• pp.37-46
• /
• 2000

본 논문에서는 부지특성을 고려한 설계지반운동의 산정방법을 연구하였으며 그 해석결과를 지반 구조물의 내진설계에 적용하는 방법을 제안하였다 지진응답 해석시 사용되는 설계응답스펙트럼과 설계시간 이력등의 입력운동의 통제점 위치가 지반구조물 내진설동 지층내 암반운동 그리고 노두운동을 사용하는 방법으로 나눌 수 있고 이에 따라 작용 설계지진운동이 변화하므로 지반구조물의 경계조건에 적합한 방법을 사용하여야 한다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.389-396
• /
• 2002

Engineers should be careful in the design of bonding piles into pile caps because they are weak points in the pile foundation. Therefore in this study, the mechanism of bonding piles into pile caps was explained, and the design method of the composite bonding method was proposed. And the proposed design method was verified in comparison with the result of the full scale test. Also, the characteristic for the bearing capacity and the mechanism of compressive load of bonding method were analyzed.