• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.529-534
• /
• 2009

This study had propose that a characteristic of recently developed Silicasol to make a close in this study, grouting material usually used portland cement and a characteristic is compared between Silicasol and sodium silicate in this study, examined strength and environmentally friendly for compare characteristics of sodium silicate and Silicasol through unconfined compressive strength, SEM analysis, Permeability test, Chemical Resistance test, leaching test etc. In the test, I gained that unconfined compressive strength of Silicasol three times promoted than sodium silicate Within 72 hours and I gined through analysis of SEM that Silicasol is more compactivetive than sodium silicate. In the result of test, it was found to be a environmentally friendly material as the toatal amount of eluviated elementary had small quantity.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.700-709
• /
• 2009

FBG sensor system is applied to the concrete lining structure in Taegu subway. Near the structure, the power cable tunnel construction started. We wanted to measure the deformation of the structure due to the construction by the FBG sensor. The applied sensor has the gauge length of 1 meter to overcome the inhomogeneity of the concrete material with enough length. In order to fix tightly to the structure, the partially stripped parts of the sensor glued to the package and slip phenomenon between fiber and acrylate jacket was prevented. Prestrain of the sensor was imposed by controlling the two fixed points with bolts and nuts in order to measure compressive strain as well as tensile strain. The behavior of subway lining structure could be monitored very well.

• Geomechanics and Engineering
• /
• v.2 no.4
• /
• pp.303-319
• /
• 2010

The effect of grain crushing on the deformation of sand in 1D compression and 1D creep at high stresses was investigated theoretically and experimentally. An approach was proposed to formulate the process of grain crushing in sand in accordance with the laws of fracture mechanics and energy conservation. With this approach, the relation between the void ratio and the amount of grains crushed in 1D compression was derived. Laboratory test data were used to verify this derived relation. In addition, it was observed that there are similarities in evolution of grain size distribution in 1D compression and 1D creep tests. This implies that the changes in microstructure in sand under 1D compression and 1D creep are comparable.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.06a
• /
• pp.45-54
• /
• 2001

In this study, slope stability analysis of LCRS(Leachate Collection Removel System) in waste landfill was peformed by large scale field test. Geocomat is new type of geocomposite product. Gecomat is a sort of Geocomposite product. It is composed of nonwoven geotextiles, woven geotextile, and geonet. Large scale field tests were performed on the slope of different two LCRSsections with static loading condition. One is LCRS section witch consist of GCL, HDPE and Geocomat, another is GCL, HDPE, and woven type geocomposite. The behavior of geosynthetics lined slope was monitored by incorporating instrumentation including vertical soil pressure meter, settlement plate, strain gauges, potential meter, displacement pin.. Based on the field monitoring, the Geocomat LCRS section is less sliding than the conventional geocomposite LCRS section.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.06a
• /
• pp.55-65
• /
• 2001

Geotextiles are usually constructed as a protective layer of geomembranes in liner systems for the solid waste landfill. A protective layer and geomembrane are susceptible to mechanical damage by coarse grains in the overlying drainage layer. In this study, therefore, the strain behavior of geotextile protective layers was investigated using three different types of devices for developing punctiform loads. The results of the study showed that the rates of strain was different depend upon device types for functiform loads. Also, It was found that the increases in strain was approximately linear in range 20 to 6$0^{\circ}C$ , and pp-filament non-woven geotextiles yielded a better efficiency than pp-staple fiber non-woven geotextiles.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.197-204
• /
• 2002

In this study, multivariate analysis based on domestic data(958 EA) of road tunnel, and suggest the easy prediction equation of Q-system. We generate applicable Q-value to numerical analysis method with using the equation and investigate the behavior as variable Q-value of rock mass induced excavation with discontinuum numerical analysis method, UDEC. In the result of the experiment, we research the application range of Q-value to apply the continuum model to discontinuous rock mass is below 0.7 and we testify the applicability of continuum model as researched Q-value with continuum numerical analysis method, FLAC.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.55-62
• /
• 2002

미소변형에서 대변형에 이르는 전체 변형률 영역의 구성모델을 ABAQUS 코드에 구현하였다. 구성모델은 비등방경화규칙에 근거한 전응력 개념의 탄소성 모델로 연약 점토나 풍화토에 적용하는 것이 가능하다. 사용된 정식화 및 알고리즘은 (1) Jaumann 응력속도를 이용한 대변형도 조건 정식화 (2) 내재적인 응력적분 (3) 일관된 접선계수를 포함하고 있다. 이를 통하여 대변형 해석을 정확하고 효율적으로 수행할 수 있었다. 예제를 통하여 새로운 구성모델과 ABAQUS 코드를 이용한 대변형 해석을 수행할 수 있음을 확인하였다. 특히 전체변형률 영역의 거동을 모델하고 범용 해석 프로그램을 이용한 비선형 대변형 해석에 적용하는 것이 가능하였다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09c
• /
• pp.125-128
• /
• 2010

A large quantity of purified water sludge is generated in modern cities around the world. Dewatering is essential to reduce the volumes transported off-site for disposal. Traditionally employed methods such as solar drying methods are time-consuming. There are urgent demands for developing alternatives to dewater the sludge in a less time-consuming manner. In this paper, siphon method is proposed to dewater the high-water-content sludge with plastic drainage plate installed horizontally. A group of comparative tests are conducted to preliminarily investigate the dewatering behavior of the purified water sludge with siphon and solar drying methods, respectively. On the basis of the test results, the availability and effectiveness of the new method is verified. It may provide an innovative solution to treat the purified water sludge more effectively.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09c
• /
• pp.49-54
• /
• 2010

In order to study the performance of levees reinforced with steel sheet piles under high water condition, a series of model tests was conducted by simulating the high water condition before and after applying severe seismic loading history. As a result, the seepage behavior through the subsoil layers underlying the levee was not significantly affected by the seismic loading history. It was also verified that, irrespective of the seismic loading history, the sheet piles installed at the levee crest or shoulder are effective in preventing the breakage of levees caused by overflow. In addition, applicability of drainage works at the foot of the levee in preventing the seepage failure was confirmed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1992.12a
• /
• pp.19-32
• /
• 1992

Objectives of this study are : 1) to utilize capillary theory and obtain pore-size distribution profiles from moisture-suction relationships using Laplace theory. 2) to investigate the behavior of Light Non-Aqueous Phase Liquids(LNAPLs) in the subsurface environment and to develop several predictive relationships which can be used to assess the effectiveness of various LNAPLs remediation technologies. The relationship to predict pore-size distribution function expressed in differencial equation is found by using capillary theory. Also, experiments are conducted to : the various LNAPLs subjected to vadose zone drainage, groundwater table drainage, waterflooding with surfactants. The experiments are performed with #2 heating oil, jet fuel. and kerosene. Several relationships have been derived describing the effect of various properties and process parameters on the LNAPL residual saturation.