• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.103-111
• /
• 2017

Saudi Arabia coastal area is highly valuable construction as a flat area covered by sabkha deposit. However, sabkha deposit has some geotechnical problems because of high groundwater level, high salt contents in groundwater, loose density, and possibility of collapsible settlement due to presence of crystals vulnerable to moisture, and ground improvement is needed to improve the bearing capacity. In this study, the characteristics of the sabkha soils in the coastal area of Saudi Arabia were analyzed and the applicability of dynamic compaction method was evaluated. Parametric study was conducted to analyze the behavior of sabkha deposit during dynamic compaction. The appropriateness of the proposed analytical solutions to estimate the depth of improvement was evaluated, and the troubles and notes in applying dynamic compaction in sabkha deposit were discussed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.389-396
• /
• 1999

In this study compressive and tensile load tests have been performed to investigate reinforcing effect and load transfer mechanism of small diameter piles installed in the foundation soil for the marine suspension bridge. Load tests were carried out on steel plate with diameters of 50cm, 100cm and 150cm varying loads starting from 39 tons up to 314 tons. Small diameter piles were proved to behavior like as friction piles and loads were not transmitted to the bottom of piles. From pull-out tests, the uplift capacity of small diameter piles was largely influenced by reinforcing materials compared to frictional resistance between piles and adjacent soils. The bearing capacity of small diameter piles appeared to be higher than the ultimate bearing capacity evaluated using static formulae. The load carrying capacity of small diameter piles was superior to the bored piles with a similar size. Thus, ultimate bearing capacity estimated from static formulae can provide conservative designs and thereby resulting in economic disadvantages. A further study to accumulate data regarding various soil conditions is recommended for an improved estimation of bearing capacity of piles with small diameter.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.397-404
• /
• 1999

It is essential to measure load transfer mechanism of pile to check the appropriateness of assumptions made for design purpose and to continuously monitor the behavior of pile foundation. Through many attempts to monitor the behavior of super-structure in civil engineering area using several optical fiber sensors have been made, application of optical fiber sensor technology on pile foundation has not been tried up to now. Load transfer of model piles during compression loading was measured by optical fiber sensors and compared with the measurement by strain gauges. Fiber Bragg Grating(FBG) sensor system was used since it has many advantages, such as easy multiplexing, high sensitivity, and simple fabrication. Besides the model pile tests, uniaxial tension test of steel bar and compression tests of mortar specimen were carried out to evaluate the performance of FBG sensors in embedded environments. The shift of refilming wavelength due to the strain in FBG sensor is converted to the strain at sensor location and the dependence between them is 1.28 pm/${\mu}$ strain. FBG sensors embedded in model pile showed a better survivability than strain gauges. Measured results of load transfer by both FBG sensors and strain gauges were similar, but FBG sensors showed a smoother trend than those by strain gauge. Based on the results of model pile test, it was concluded that the use of FBG sensor for strain measurement in pile has a great potential for the analysis of pile load transfer.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.67-74
• /
• 1999

Self-Boring Pressuremeter Test(SBPT) is known to be the most effective in-situ test method which can reliably determine consolidation characteristics as well as deformation modules and untrained shear strength. In order to derive the coefficient of consolidation using SBPT results it is necessary to obtain the dissipation behavior from the pore pressure change with time during constant radial strain(generally 10%) and to derive the reliable time factor(Τ) from the analytical method which considers the real in-situ conditions. As previous studies on time factor are based on the assumptions of plane strain condition that the membrane of SBP is infinite, of untrained condition during the expansion of the probe and of elastic soil behavior during consolidation, these analyses can't consider the real boundary conditions and the real soil behaviour. In this study, consolidation analysis similar to real in-situ conditions including test procedure is conducted using finite element program which employs MCC model and Biot theory. Time factor considering the effects of finite membrane length, the total pressure change during consolidation and partial drainage is proposed and compared with previous results.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.587-597
• /
• 2010

Analysis of the behavior of a laterally loaded pile is important in the design of critical civil structures. Recently, the electric strain gauge has been widely used to measure the strains along the pile. The electric strain gauge, due to lack of durability, is inappropriate in the use of long-term measurements. Herein, the feasibility of implementing the FBG sensor was investigated using a cantilever-type calibrator in laboratory. A special calibrating tool called "cantilever-calibrator" was used to calibrate the FBG sensors. The calibrator consists of a special calibration beam, a holding-clamp at one end of the beam, and a micrometer on the other end. Three FBG sensors were installed on the calibration beam. The strains measured by FBG sensors were compared with those calculated theoretically using cantilever beam theory. The calibration factor of FBG sensors were suggested to compensate the difference between measured and calculate strains.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1156-1167
• /
• 2010

The constant rate of strain (CRS) consolidation test has been widely used to evaluate consolidation characteristics of soils instead of the standard Incremental Loading Test. In practical problems, after the ground improvement, the condition of the soil is over-consolidated. Therefore, it is important to determine the recompression indices and the coefficient of consolidation(or the coefficient of swelling) of unloading-reloading cycle to predict the settlement behavior. However, since standard testing procedures or studies related with strain rate are insufficient especially in unloading-reloading cycle, it is difficult to predict the settlement field behavior accurately from the CRS consolidation test results in spite of its lots of strengths. The several CRS consolidation tests were performed changing the unloading strain rate from 0.2%/hr to 20%/hr with vertical drainage condition using the reconstituted kaolinite sample. For the reconstituted kaolinite sample in CRS consolidation test, the recompression indices are insensitive to the strain rate. It is revealed that the coefficient of consolidation of reloading is affected by the developed pore pressure during unloading. Additionally, the test should be conducted in the positive pore pressure ratio range (3~15%) to obtain the reasonable coefficient of consolidation in the whole range(loading, unloading and reloading).

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.598-604
• /
• 2010

The drilled pier foundation is widely used to support transmission line structures due to its simplicity of construction. When this foundation type is used in conjunction with a single shaft or H-frame structure, it is subjected to a high overturning moment, combined with modest vertical and shear loads. Since the length and diameter of drilled piers are often governed by a maximum permissible deflection, many drilled piers being installed today are very conservatively designed. In this study, Nine prototype field-tests (1/8 scale) have been conducted in order to determine the vertical and lateral resistance of drilled pier foundation for single pole structures. These test results reveal the test piers behaved essentially as rigid bodies in soil (6D) and the center of rotation of the pier were typically 0.6~0.4 of the pier depth below ground surface. Test results also show the relationship between the applied load and the deflection at the top of the pier is highly nonlinear.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.201-204
• /
• 2010

Earthquake load to design a structure has been calculated from a fixed base SDOF model using amplified surface accelerations along soft soil layers. But the method dose not consider a soil-structure interaction. Centrifugal experiments that were consisted of soil, a shallow foundation and a structure were performed to find the effects of soil-structure interaction. The experiments showed that mass and stiffness of the foundation affected a response of the structure and nonlinear behavior of soil near the foundation. And a rocking displacement caused by overturning moment affected the response and increases a damping effect. In this study, the centrifugal experiment was simulated as a two dimensional finite element model. The finite element model was used for nonlinear time domain analysis of the OpenSees program. The numerical model accurately evaluated the behaviors of soil and the foundation, but the rocking effect and the behavior of structure were not described.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.49-83
• /
• 2005

ESCP Project showed an urban excavation case and introduced design method for case of Soil-Structure behavior in urban excavation. In this case, a retaining structures design to analysis the behavior of retaining wall and adjacent structures in urban excavations was applied by using a Elasto-plastic beam and limit Equilibrium analysis and soil-structure interaction analysis. Reliable design of earth retaining structures and the ground adjacent to braced wall in urban excavation are often difficult due to many variable factors. The ground settlement and the damage of adjacent structures in urban excavation has been an imprtant issue. Therefore, the stability of the adjacent structures must be secured with the excavation support and research on the protection of adjacent structure is necessary.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.4
• /
• pp.303-314
• /
• 2004

This study is intended to investigate the geotechnical behavior of jointed mass on tunnel excavation experimentally. Laboratory test were conducted in various conditions of distance from joint to tunnel and in-situ stress ratio ($K_0$). In case, the ground around the tunnel that has the joint angle $90^{\circ}$ generate the greatest influence in crown and far shoulder from joint. If the in-situ stress ratio is low, tangential stress of side wall that is opposite side of the joint is increased more than in crown. Otherwise in case, joint angle $45^{\circ}$, the generated compress stress is found out that left side of the tunnel of near the joint has influence on stability of the tunnel about 3 times than non-jointed rock.