• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.2
• /
• pp.119-126
• /
• 2008

In this paper, the loop coupling model for the analysis of end launcher rectangular waveguide adapter are proposed. The formula of input impedance from this model are presented. The influence of propagation mode and higher modes in rectangular waveguide are analyzed and design parameters of the end launcher adapter are investigated. The computational results between the proposed theoretical analysis and the previous papers are compared and are verified by HFSS. The end launcher rectangular waveguide adapter consists of the coupling geometry which is connected the inner conductor of $50{\Omega}$ coaxial line through into the 17.6mm feeding loop in a WR90 commercial waveguide, and the VSWR is maximum 2.0 over operating frequency from 7.5GHz to 10.6GHz.

• Korean Journal of Computational Design and Engineering
• /
• v.19 no.4
• /
• pp.356-367
• /
• 2014

A robotic sapatial augmented reality (RSAR) system, which combines robotic components with projector-based AR technique, is unique in its ability to expand the user interaction area by dynamically changing the position and orientation of a projector-camera unit (PCU). For a moving PCU mounted on a conventional robotic device, we can compute its extrinsic parameters using a robot kinematics method assuming a link and joint geometry is available. In a RSAR system based on user-created robot (UCR), however, it is difficult to calibrate or measure the geometric configuration, which limits to apply a conventional kinematics method. In this paper, we propose a data-driven kinematics control method for a UCR-based RSAR system. The proposed method utilized a pre-sampled data set of camera calibration acquired at sufficient instances of kinematics configurations in fixed joint domains. Then, the sampled set is compactly represented as a set of B-spline surfaces. The proposed method have merits in two folds. First, it does not require any kinematics model such as a link length or joint orientation. Secondly, the computation is simple since it just evaluates a several polynomials rather than relying on Jacobian computation. We describe the proposed method and demonstrates the results for an experimental RSAR system with a PCU on a simple pan-tilt arm.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.49-52
• /
• 2011

A dinuclear copper(II) complex of [$Cu_2(aceace)_4$(dipyph)] [aceace = acetylacetone, dipyph = 1,4-di(4-pyridylethene-2-yl-)benzene] has been synthesized and characterized by elemental analysis, IR and X-ray single crystal diffraction. It crystallizes in the monoclinic system, space group P21/c, with lattice parameters a = 7.9584(16) $\AA$, b = 18.594(4) $\AA$, c = 15.063(4) $\AA$ $\beta=120.97(2)^o$ and $M_r$ = 807.85 ($C_{40}H_{44}Cu_2N_2O_8$), Z = 2. Each of the $Cu^{2+}$ ion adopts a square pyramid geometry and coordinates with four oxygen atoms from two aceace ligands and one nitrogen atom from dipyph bidentate ligand. Magnetic measurement shows that the Weiss constant and Curie constant for the title compound are -0.22 K and 0.1154 emu K/mol, respectively. Thermal stability data indicate that the title complex undergoes two steps decomposition and the residue is $Cu_2O_4$. In the potential range of -1.5 ~ 0.8 V, the title complex represents an irreversible electrochemical process.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3777-3787
• /
• 2012

Three kinds of 3D isomorphous and isostructural coordination polymers, namely, $\{[Ln_2(PDA)_3(H_2O)_3]{\cdot}0.25H_2O\}_{\infty}$ (Ln = La(1), Sm(2), and Gd(3)) ($PDA^{2-}$ = pyridine-2,6-dicarboxylate anion) have been synthesized under hydrothermal conditions and characterized by elemental analyses, IR spectroscopy, thermal analyses and single crystal X-ray diffraction. In these MOFs, Ln(III) centers adopt eight-coordinated and nine-coordinated with the $N_1O_7$ and $N_2O_7$ donor sets to construct distorted trianglar dodecahedron geometry and tricapped trigonal prism configurations, respectively. Based on the building block of tetranuclear homometallic $Ln_4C_4O_8$ unit (16-membered ring), 1-3 are connected into highly ordered 2D sheets via O-C-O linkers and further constructed into 3D architectures through hydrogen bonds. Crystallographic parameters suggest that the lanthanide contraction effect exist in these coordination polymers. Luminescent properties of the lanthanide-based MOFs (metal-organic frameworks) have been measured at room temperature, which reveal that they presenting ionselective characters toward certain metals, such as $Mg^{2+}$, $Cd^{2+}$ and $Pb^{2+}$ ions.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.6
• /
• pp.45-56
• /
• 2015

This paper aims to develop a submerged propeller turbine for micro hydropower plant which allows to sustain high values of efficiency in a broad range of hydrological conditions (H=2~6 m, $Q=0.15{\sim}0.39m^3/s$). The two aspects to be considered in this development are mechanical simplicity and high-efficiency operation. Unlike conventional turbines that have spiral casing and gear box, this is directing driving and no spiral casing. A 10 kW class turbine which has the most high potential of the power generation has been developed. The most important element in the design of turbine is the runner blade. The initial blade is designed using inverse design method and then the runner geometry is modified by classical hydraulic method. The design process is carried out in two steps. First, the blade shape is fix and then other components of submerged propeller turbine are designed. Computational fluid dynamics analyses based on the Navier-Stokes equations have been used to obtain overall performance data for the blade and the full turbine, respectively. The results generated by performance parameters(head, guide vane opening angle and rotational speed) variations are theoretically analysed. The evaluation criteria for the blade and the turbine performances are the pressure distribution and flow's behavior on the runner blades and turbine. The results of simulation reveals an efficiency of 91.5% and power generation of 10.5kW at the best efficiency point at the head of 4m and a discharge of $0.3m^3/s$.

• Journal of Periodontal and Implant Science
• /
• v.23 no.3
• /
• pp.595-604
• /
• 1993

Since $Gr{\"{o}}nadhl$ et al introduced a digital subtraction radiography into periodontal dignosis in 1983, many reports using this system has aimed to assess the peroiodontal disease activity and the alveolar bone changes after periodontal treatment. The present study was performed to evaluate the usefulness of digital subtraction radiography for asessing an alveolar bone changes in 3 months after periodontal flap surgery. Serial intraral raiographs were taken from 5 normal subjects and 6 periodontally diseased patients using customized bite blocks attached to film holder in fxation device and digitized by image processing system(consisting of IBM 386, digital frame grabber, CCD camera, Image-pro II software). And the reference parameters were measured by pixel unit and compared with respective radiographs. The serial radiographs showed a little and statistically insignificant difference in reference paramenters. The conventional intraoral radiographs, the subtraction images and the clor enhanced subtraction images were reviewed by 4 examiners and the examiner's agreement rates were compared. The subtraction images and its color enhanced images showed higher examiner's agreement rate than the conventional radiographs. And the propotions of sites diagnosed with bone loss or gain after periodontal surgery were highter in the subtraction images and its color enhanced images than in the conventional radiographs. Especially, in color enhanced images, the unber of bone agin sites tended to increase according to post-surgery periods. These results indicate that projection geometry could be standardized with the divice used in this study, and the subtraction radiography may be useful to assess an alveolar bone changes after periodntal flap surgery.

• Journal of Korean Association for Spatial Structures
• /
• v.12 no.2
• /
• pp.45-53
• /
• 2012

This paper derives Isogeometric analysis and post-processing method of surface that are generated by NURBS basis function for accurate geometric modeling and structure analysis of free-form. By deforming these parameters that are consisted of control points, knots, polynomial, variable geometric models are derived. The basis function that is used to Isogeometric analysis is same to the basis function of NURBS that is used to generate geometric models. For performing isogeometric analysis, h-p-k refinement is performed without changing of original geometry. To visualize the results of isogeometric analysis that control points' displacements, post-processing method that is the interface method between IGES format and Rhinoceros is derived.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.6
• /
• pp.313-318
• /
• 2006

This paper introduces a partial discharge (PD) severity metric, S, based on the evaluation of time-sequence PD data capture and resulting Time-Sequence-Analysis Discharge (TSAD) level distributions. Basically based on an IEC60270 measurement technique, each PD event is time stamped and the discharge level noted. By evaluating the time differences between a previous and subsequent discharge, a 3D plot of time-sequence activity and discharge levels can be produced. From these parameters a measurement of severity, which takes into account dynamic or instantaneous variations in both the time of occurrence and the level of discharge, rather than using standard repetition rate techniques, can be formulated. The idea is to provide a measure of the severity of PD activity for potentially measuring the state of insulation within an item of plant. This severity measure is evaluated for a simple point-plane geometry in $SF_{6}$ as a function of gap distance and applied high voltage. The results show that as the partial discharge activity increases, the severity measure also increases. The importance of future investigations, quantifications and evaluations of the robustness, sensitivity and importance of such a severity measurement, as well as comparing it with typical repetition rate assessment techniques, and other monitoring techniques, are also very briefly discussed.

• Structural Engineering and Mechanics
• /
• v.40 no.1
• /
• pp.65-84
• /
• 2011

In this paper a simple mathematical model for approximate static analysis of combined system of framed tube, shear core and two outrigger-belt truss structures subjected to lateral loads is presented. In the proposed methodology, framed tube is modeled as a cantilevered beam with a box section and interaction between shear core and outrigger-belt truss system with framed tube is modeled using torsional springs placed at location of outrigger-belt truss; these torsional springs act in a direction opposite to rotation generated by lateral loads. The effect of shear lag on axial deformation in flange is quadratic and in web it is a cubic function of geometry. Here the total energy of the combined system is minimized with respect to lateral deflection and rotation in plane section. Solution of the resulting equilibrium equations yields the unknown coefficients of shear lag along with the stress and displacement distributions. The results of a numerical example, 50 storey building subjected to three different types of lateral loading obtained from SAP2000 are compared to those of the proposed method and the differences are found to be reasonable. The proposed method can be used during the preliminary design stages of a tall building and can provide a better understanding of the effects of various parameters on the overall structural behavior.

• Steel and Composite Structures
• /
• v.33 no.5
• /
• pp.717-727
• /
• 2019

This paper is motivated by the lack of studies in the technical literature concerning to vibration analysis of a single-layered graphene sheet (SLGS) with corner cutout based on the nonlocal elasticity model framework of classical Kirchhoff thin plate. An isogeometric analysis (IGA) based upon non-uniform rational B-spline (NURBS) is employed for approximation of the L-shape SLGS deflection field. Trimming technique is employed to create the cutout in geometry of L-shape plate. The L-shape plate is assumed to be Free (F) in the straight edges of cutout while any arbitrary boundary conditions are applied to the other four straight edges including Simply supported (S), Clamped (C) and Free (F). The Numerical studies are carried out to express the influences of the nonlocal parameter, cutout dimensions, boundary conditions and mode numbers on the variations of the natural frequencies of SLGS. It is precisely shown that these parameters have considerable effects on the free vibration behavior of the system. In addition, numerical results are validated and compared with those achieved using other analysis, where an excellent agreement is found. The effectiveness and the accuracy of the present IGA approach have been demonstrated and it is shown that the IGA is efficient, robust and accurate in terms of nanoplate problems. This study serves as a benchmark for assessing the validity of numerical methods used to analyze the single-layered graphene sheet with corner cutout.