• Journal of ILASS-Korea
• /
• v.4 no.3
• /
• pp.32-41
• /
• 1999

In this research, internal-mixing twin-fluid atomizer using sonic energy is designed and manufactured. We are trying to intimate high efficiency twin-fluid atomizer to obtain good liquid atomization in the low pressure region. Define of geometric form of atomizer, characteristics of spray is influenced by position, depth and height variation of cavity resonator, variation of sound intensity and resonant sound frequency with liquid flow rate. The liquid atomization is promoted by multi-stage disintegration of mixing flow of gas with liquid and the optimum condition of position and depth of cavity resonator according to sonic energy is obtained from the condition at a=2.5mm and L=2mm. The velocity distribution of droplets shows negative value due to recirculation region at the center of axial, and as the radial direction distance is far, the velocity distribution of droplets decrease slowly after having a maximum value. However velocity and SMD show nearly uniform distribution at the down stream and as result compared to Nukiyama and Tanasawa's equation. atomization of mixing flow with air and liquid dispersing from the outlet of the nozzle is promoted by the effect of collision at the cavity resonator.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.2
• /
• pp.127-135
• /
• 2009

A conventional centrifugal pump causes a drastic deterioration of air-water two-phase flow performances even at an air-water two-phase flow condition of inlet void fraction less than 10% in the range of relatively low water flow rate. Then we have developed a two-phase flow centrifugal pump which consists of a tandem arrangement of double rotating cascades and blades of outer cascade have higher outlet angle more than $90^{\circ}$. In design of the two-phase flow pump for various sized and operating conditions, similarity relations of geometric dimensions to hydraulic performances is very useful. The similarity relations of rotational speed, impeller diameter and blade height are investigated for the developed impeller in the present paper. As the results, the similarity law of rotational speed and impeller diameter is clarified experimentally even in two-phase flow condition. In addition, influences of blade height on air-water two-phase flow performances indicate a little difference from the similarity relations.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.462-467
• /
• 2005

This paper presents virtual machining system in order to realize turning process in virtual space. A reliable virtual turning process simulation was developed based on the surface shaping system which is capable of considering geometric model, thermal error model, and vibration model. Accuracy of surface shape resulting from proposed machining simulator was verified experimentally. This paper also developed the watchdog agent that continuously assessed, diagnosed, and predicted performance of products and machines in machining. The Watchdog agent extracted feature signal using time-frequency analysis among various signals from multi-sensor and evaluated machining condition using performance confidence value.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.2
• /
• pp.50-57
• /
• 2008

The effect of weld improvement on the corroded fatigue life of welded structures was investigated. Toe grinding, TIG dressing and weld profiling were used as the geometric improvement methods. Fatigue tests under the corroded condition in artificial seawater were carried out to investigate the corrosion fatigue behavior of API 2W Gr.50T steel plate produced by POSCO. The test results in weld improved conditions were compared with those in as-welded condition. The test results were also compared with the design curves in UK DEn Class F. Corroded fatigue life of weld improved specimens was longer than that of as-welded specimen. Especially, the corroded fatigue life exceeded the mean SN curve in air of UK DEn Class F.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.2
• /
• pp.22-32
• /
• 2010

The world is facing environmental problem described as climate change and exhaustion of fossil fuel. In order to solve theses problems, importance of renewable energy is extremely growing. For stable energy supply, it is need to apply hybrid renewable energy systems in urban-scale, because some renewable energy system' outputs are greatly influenced by climatic condition. Especially, solar irradiation and wind velocity are influenced by urban geometric environment as well as climatic condition. Therefore it is necessary to evaluate the renewable energy potential according as urban form. This study aims to evaluate the potential of solar energy and wind energy in urban-scale and classify urban type according as characteristics of urban forms. The results of this study will be used to develop renewable energy system application guidelines for urban and energy planning.

• Safety and Health at Work
• /
• v.1 no.1
• /
• pp.43-50
• /
• 2010

Objectives: The objective of this study was to investigate the effect of chain installation condition on stress distribution that could eventually cause disastrous failure from sudden deformation and geometric rupture. Methods: Fractographic method used for the failed chain indicates that over-stress was considered as the root cause of failure. 3D modeling and finite element analysis for the chain, used in a crane hook, were performed with a three-dimensional interactive application program, CATIA, commercial finite element analysis and computational fluid dynamic software, ANSYS. Results: The results showed that the state of stress was changed depending on the initial position of the chain that was installed in the hook. Especially, the magnitude of the stress was strongly affected by the bending forces, which are 2.5 times greater (under the simulation condition currently investigated) than that from the plain tensile load. Also, it was noted that the change of load state is strongly related to the failure of parts. The chain can hold an ultimate load of about 8 tons with only the tensile load acting on it. Conclusion: The conclusions of this research clearly showed that a reduction of the loss from similar incidents can be achieved when an operator properly handles the installation of the chain.

• Nuclear Engineering and Technology
• /
• v.51 no.5
• /
• pp.1209-1217
• /
• 2019

Due to the limitation of the computers, the conventional homogenization method is based on many assumptions and approximations, and some tough problems such as energy spectrum and boundary condition are faced. To deal with those problems, the Monte Carlo global homogenization is adopted. The Reactor Monte Carlo code RMC is used to study the global homogenization method, and the one-step global homogenization method is proposed. The superimposed mesh geometry is also used to divide the physical models, leading to better geometric flexibility. A set of multigroup homogenization cross sections is online generated for each mesh under the real neutron energy spectrum and boundary condition, the cross sections are adjusted by the superhomogenization method, and no leakage correction is required. During the process of superhomogenization, the author-developed reactor core program NLSP3 is used for global calculation, so the global flux distribution and equivalent homogenization cross sections could be solved simultaneously. Meanwhile, the calculated homogenization cross section could accurately reconstruct the non-homogenization flux distribution and could also be used for fine calculation. This one-step global homogenization method was tested by a PWR assembly and a small reactor model, and the results show the validity.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.4
• /
• pp.235-242
• /
• 2022

As ship condition inspection technology has been developed, research on collecting, analyzing, and diagnosing condition information has become active. In ships, related research has been conducted, such as analyzing, detecting, and classifying major hull failures such as cracks and corrosion using 2D and 3D data information. However, for geometric deformation such as indents and bulges, 2D data has limitations in detection, so 3D data is needed to utilize spatial feature information. In this study, we aim to detect hull structural deformation positions. It builds a specimen based on actual hull structure deformation and acquires a point cloud from a model scanned with a 3D scanner. In the obtained point cloud, deformation(outliers) is found with a combination of RANSAC algorithms that find the best matching model in the Octree data structure and dataset.

• Steel and Composite Structures
• /
• v.42 no.5
• /
• pp.699-710
• /
• 2022

This work presents a comprehensive study on the surface energy effect on the axial frequency analyses of AFGM nanorods in cylindrical coordinates. The AFGM nanorods are considered to be thin, relatively thick, and thick. In thin nanorods, effects of the inertia of lateral motions and the shear stiffness are ignored; in relatively thick nanorods, only the first one is considered; and in thick nanorods, both of them are considered in the kinetic energy and the strain energy of the nanorod, respectively. The surface elasticity theory which includes three surface parameters called surface density, surface stress, and surface Lame constants, is implemented to consider the size effect. The power-law form is considered for variation of the material properties through the axial direction. Hamilton's principle is used to derive the governing equations and boundary conditions. Due to considering the surface stress, the governing equation and boundary condition become inhomogeneous. After homogenization of them using an appropriate change of variable, axial natural frequencies are calculated implementing harmonic differential quadrature (HDQ) method. Comprehensive results including effects of geometric parameters and various material properties are presented for a wide range of boundary condition types. It is believed that this study is a comprehensive one that can help posterities for design and manufacturing of nano-electro-mechanical systems.

• Design & Manufacturing
• /
• v.16 no.2
• /
• pp.46-52
• /
• 2022

As the consumer market in the eco-friendly vehicle industry grows, the demand for water pump in a electric car parts market. This study intend to propose a mathematical model that can verify the effect of improving thermal properties when a non-conductive cooling filler liquid is introduced into an electric vehicle water pump. Also, the pros and cons of the immersion cooling method and future development way were suggested by analyzing the cooling characteristics using on the derived analysis solution. Thermal characteristics analysis of electric water pump applied with non-conductive filler liquid was carried out, and the diffusion boundary condition in the motor body and the boundary condition the inside pump were expressed as a geometric model. As a result of analyzing the temperature change for the heat source of the natural convection method and the heat conduction method, the natural convection method has difficulty in dissipating heat because no decrease in temperature due to heat release was found even after 300 sec. Also, it can be seen that the heat dissipation effect was obtained even though the non-conductive filling liquid was applied at the 120 sec and 180 sec in the heat conduction method. It has proposed to minimize thermal embrittlement and lower motor torque by injecting a non-conductive filler liquid into the motor body and designing a partition wall thickness of 2.5 mm or less.