• Journal of Adhesion and Interface
• /
• v.19 no.2
• /
• pp.74-82
• /
• 2018

Many methods for cross-linking acrylic PSAs have been discussed previously. For high cross-linking density, epoxy functionalized monomer and methyl aziridines as cross-linking agents were used in this study. Additionally, photopolymerization using different UV doses was investigated to synthesize a binder because of its rapid productivity. FT-IR analysis, curing behaviours and adhesion performance were examined for the relationship between UV doses and temperature as curing conditions. According to the results, the gel fraction was over 50% even at $120^{\circ}C$ after UV curing at a dose of $800mJ/cm^2$. On the other hand, while gel fractions of all samples reached approximately 80% only at $180^{\circ}C$ in thermal curing for 1 hour, gel fractions of the samples after thermal curing for 3 hours increased rapidly above $120^{\circ}C$ regardless of UV doses and reached approximately 100% at $180^{\circ}C$. This means that the second cross-linking reaction, esterification, is mainly dependent on the curing temperature.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.1
• /
• pp.38-43
• /
• 2004

Porous carbon aerogel-silica gel composite materials were used as the electrodes of capacitive deionization(CDI) process, which were prepared by a paste rolling method. The electrochemical parameters such at current values, coulombs af a function of cycle, and CDI efficiencies were investigated for 10th and 100th cycles in 1,000ppm NaCl solution. Carbon aerogel-silica gel composite electrodes showed good wet-ability and higher mechanical strengths even under the NaCl solutions as well. In our experimented runs, all of the composite electrodes also are showed good cycle-ability without destroy of active material during cycles and decreased manufacturing times by $50\%$. Conclusively, the adding of silica gel powder to carbon aerogel leads to the effective performance of CDI process due to effective utilization of active materials by increasing the wet-ability and mechanical hardness.

• Korean Journal of Materials Research
• /
• v.11 no.2
• /
• pp.94-103
• /
• 2001

SiO$_2$ and PDMS/SiO$_2$ xerogels which are derived PDMS into TEOS have been synthesized by sol-gel process and controlled pore size and distribution through 2 step acid/base catalyzed processes using HCI and NH$_4$OH as a catalyst. In HCl catalyzed SiO$_2$ and PDMS/SiO$_2$ xerogels, pH and gellation time of xerogel were 2.3~2.5 and 12~13 days, respectively, and the shape of xerogel was identified to pellet type and column type. Under acidic condition of final reaction solution, the hydrolysis rate is accelerating, resulting in long gel times. The shape of xerogel is pellet type. In contrast, under less acidic condition, the condensation rate is accelerating, resulting in shorter gel times and the shape of xerogel is column type. The surface area and average Pore size were changed 400$\rightarrow$600($\m^2$/g) and 15$\rightarrow$28$\AA$, respectively, depending to the increase of the mole ratio of HCl/NH$_4$OH, and represented uniform pore size distribution. It is that all the alkoxide groups are hydrolyzed by HCl after the first step and the condensation rate is enhanced by NH$_4$OH. The regular backbone structures of silica are formed at low temperature and the uniform pores are produced by heat treatment.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.2
• /
• pp.117-124
• /
• 2011

We demonstrate a new surface modification of high-voltage lithium cobalt oxide ($LiCoO_2$) cathode active materials for lithium-ion batteries. This approach is based on exploitation of a polarity-tuned gel polymer electrolyte (GPE) coating. Herein, two contrast polymers having different polarity are chosen: polyimide (PI) synthesized from thermally curing 4-component (pyromellitic dianhydride/biphenyl dianhydride/phenylenediamine/oxydianiline) polyamic acid (as a polar GPE) and ethylene-vinyl acetate copolymer (EVA) containing 12 wt% vinyl acetate repeating unit (as a less polar GPE). The strong affinity of polyamic acid for $LiCoO_2$ allows the resulting PI coating layer to present a highly-continuous surface film of nanometer thickness. On the other hand, the less polar EVA coating layer is poorly deposited onto the $LiCoO_2$, resulting in a locally agglomerated morphology with relatively high thickness. Based on the characterization of GPE coating layers, their structural difference on the electrochemical performance and thermal stability of high-voltage (herein, 4.4 V) $LiCoO_2$ is thoroughly investigated. In comparison to the EVA coating layer, the PI coating layer is effective in preventing the direct exposure of $LiCoO_2$ to liquid electrolyte, which thus plays a viable role in improving the high-voltage cell performance and mitigating the interfacial exothermic reaction between the charged $LiCoO_2$ and liquid electrolytes.

• Korean Journal of Materials Research
• /
• v.11 no.11
• /
• pp.960-964
• /
• 2001

$Bi_{3.99}Ti_{2.97}V_{0.03}O_{12}$ (BTV) thin films with 3 mol% vanadium doping were Prepared on $Pt/Ti/SiO_2/Si$ substrate by sol-gel method. X-ray diffraction analysis indicated that single-phase layered perovskite were obtained and preferred orientation was not observed. Under the annealing temperature at $600^{\circ}C$, the surface morphology of the BTV thin films had fine-rounded particles and then changed plate-like at $650^{\circ}C$ and $700^{\circ}C$. The remanent polarization $(2P_r)$ and coercive field $(2E_c)$ of $700^{\circ}C$ annealed BTV thin film were 25 $\mu$C/cm$^2$ and 116 kV/cm, respectively. In addition, BTV thin film showed little polarization fatigue during $10_9$ switching cycles. These improved ferroelectric properties were attributed to the increased rattling space and reduced oxygen vacancies by substitution $Ti^{4+}$ ion (68 pm) with smaller $V^{5+}$ ion (59 pm). The dielectric constant and loss were measured 130 and 0.03 at 10 kHz, respectively.

• Korean Journal of Materials Research
• /
• v.10 no.5
• /
• pp.328-334
• /
• 2000

The photocatalyst of $TiO_2$coated on glass bead was prepared from sol-gel method to remove the VOC (vola-tile organic compounds) by the photocatalytic reaction. The coated films were characterized by X-ray diffraction(XRD), specific surface area(BET), and scanning electron microscopy observation (SEM), The gas-phase photocatalytic degradation of trichloroethylene(TCE) and benzene with coated titanium dioxide on glass beads was in-vestigated using a fixed bed reactor. The degradation was calculated by the concentration difference with the retained on the reactor with aid of gas chromatography. At steady state, conversion yields were obtained for 80% of trichloroeth-vlene in 400 ppmv concentration and 65% on benzene in the range of concentration from 50 to 300 ppmv, respectively.

• Korean Journal of Materials Research
• /
• v.17 no.1
• /
• pp.18-24
• /
• 2007

Mullite-PSZ composite was prepared by sol-gel method using $Al(sec-OC_4H_9)_3,\;Si(OC_2H_5)_4,\;ZrOCl_2\;8H_2O\;and\;Y_2O_3$. The sinterability ana mechanical properties of powder compacts sintered at $1,650^{\circ}C$ for 4 hrs were investigated for various PSZ contents. In result Al-Si spinel formed at $980^{\circ}C$ from amorphous dried gel, and zirconia as well as mullite crystal formed above $1,200^{\circ}C$. The sintered body was densified to $97{\sim}98%$ except the specimen containing 25vol% PSZ which showed the relative density of about 95% obtained by sintering at $1,650^{\circ}C$ for 4 h. The flexural strength of the sintered body was a maximum value of 290 MPa in 20 vol% PSZ, which was also considerably larger than the value of 200 MPa without PSZ. The value of the fracture toughness increased linearly with increase of PSZ content and showed a maximum value of $4.3MPam^{1/2}$ in 25 vol% PSZ, Namely this value was remarkably larger than the $value(2.6MPam^{1/2})$ of pure mullite without PSZ.

• Korean Journal of Materials Research
• /
• v.24 no.6
• /
• pp.310-318
• /
• 2014

In this experiment, a highly porous scaffold of biphasic calcium phosphate (BCP) was prepared using the spongereplica method. The BCP scaffold was coated with 58S bioactive glass (BG) and sintered for a second time. The resulting scaffold was coated with gelatin (Gel) and cross-linked with [3-(3-dimethyl aminopropyl) carbodiimide] and N-Hydroxysuccinamide (EDC-NHS). The initial average pore size of the scaffold ranged from 300 to $700{\mu}m$, with more than 85 % porosity. The coating of BG and Gel had a significant effect on the scaffold-pore size, decreasing scaffold porosity while increasing mechanical strength. The material and surface properties were evaluated by means of several experiments involving scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) and X-ray diffraction (XRD). Cytotoxicity was evaluated using MTT assay and confocal imaging of MC3T3-E1 pre-osteoblast cells cultured in vitro. Three types of scaffold (BCP, BCP-BG and BCP-BG-Gel) were implanted in a rat skull for in vivo evaluation. After 8 weeks of implantation, bone regeneration occurred in all three types of sample. Interestingly, regeneration was found to be greater (geometrically and physiologically) for neat BCP scaffolds than for two other kinds of composite scaffolds. However, the other two types of scaffolds were still better than the control (i.e., defect without treatment).

• Applied Biological Chemistry
• /
• v.37 no.1
• /
• pp.49-55
• /
• 1994

An acidic protein, RCG-2, containing chitinase and ${\beta}-1,3-glucanase$ activity conccurrently was purified from rice leaves by chromatofocusing and gel slicing. The purified enzyme gave a single band on polyacrylamide gel electrophoresis and its molecular weight was appeared to be 29.7 kd using SDS-PAGE. This enzyme also had lysozyme activity. The optimal temperature for both enzyme activities was $40^{\circ}C$, optimal pH were 4.0 for chitinase activity and 7.0 for ${\beta}-1,3-glucanase$ activity. $K_M$ and $V_{max}$ values for chitinase were 7.86 mM and $0.025\;{\mu}M/min.$, and those for ${\beta}-1,3-glucanase$ were 5.95 mM and $0.16\;{\mu}M/min.$ respectively. TLC analysis of the enzyme hydrolysates of chitooligosaccharides indicated that this enzyme acts as endochitinase.

• Journal of Conservation Science
• /
• v.21
• /
• pp.21-32
• /
• 2007

Low-viscosity alkoxysilanes that polymerize into the porous network of decayed stone by a sol-gel process are widely used as stone consolidants. During drying, the gel network contracts due to capillary pressure generated by solvent evaporation. We have prepared tetraethoxysilane mixed solution containing methyltrisilane, ethyl trisilane and (3-glycidyloxypropyl)trimethoxysilane having epoxy ring in order to reduce the shrinkage happened inside the stone porous structure during the gel formation. Mixed solutions were applied into sandstone and granites and characterized by FT-IR, SEM. The gelation time, water uptake, contact angles were measured and compared with those of the commercial stone conservation materials.