• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.274-278
• /
• 2008

Hard coating solutions were prepared from glycidoxypropyl trimethoxysilane (GPTMS) and methacryloxypropyl trimethoxysilane (MPTMS) precursors with different molar ratios of 10:0, 9:1, 7:3, 5:5, 3:7, and 0:10, respectively, by the sol-gel method. The polycarbonate (PC) sheets were spin-coated, and cured at $130^{\circ}C$ for 3 h. The effect of the GPTMS:MPTMS molar ratios of the mixture was investigated on the properties of coating films. The highest pencil hardness and adhesion to PC sheets of coating films were found for solution with GPTMS:MPTMS molar ratio of 5:5. Also, the pencil hardness of coating films was increased with increasing the $H_2O$ content in the coating solutions.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.6
• /
• pp.262-266
• /
• 2010

The Calcium-aluminate electride thin films on the quartz substrates was coated by sol-gel process. The crystallization of the C12A7 thin film was observed at $800^{\circ}C$ and high density C12A7 thin film was achieved on heat treatment at $1,200^{\circ}C$ for 1 hour. The reduction heat treatment of C12A7 thin film could be converted from insulator to conductor and the electrical conductivity was 120 S/cm in the C12A7 thin film heat treated at $1,200^{\circ}C$ with $H_2$ gas for 48 hours.

• Journal of the Korean Ceramic Society
• /
• v.40 no.2
• /
• pp.153-158
• /
• 2003

Self-patterning of thin films using photosensitive sol solution has advantages such as simple manufacturing process compared to photoresist/dry etching process. In this study,$La_{0.5}SR_{0.5}CoO_3$(LSCO) thin films as an electrode material for ferroelectric memories have been prepared by spin coating method using photosensitive sol solution. La-2methoxyethoxide, Sr-ethoxide, Co-2methoxyethoxide were used as starting materials. As UV exposure time to the LSCO gel thin film increased, the UV absorption peak intensity of metal${beta}$-diketonate decreased due to reduced solubility by M(metal)-O-M bond formation. Solubility difference by UV irradiation on LSCO gel thin film allows to obtain a fine patterning of thin film. The LSCO thin films annealed over$680{\circ}C$ in air showed perovskite phase and the lowest resistivity$(4{ imes}10^{-3}{Omega}cm)$ of the thin films were obtained by annealing at$740{\circ}C$.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.5
• /
• pp.617-627
• /
• 2006

Statement of problem: HA has been used as a coating material on Ti implants to improve osteoconductivity. However. it is difficult to form uniform HA coatings on implants with complex surface geometries using a plasma spraying technique. Purpose : To determine if Ti6Al4V sintered porous-surfaced implants coated with HA sol-gel coated and hydrothermal treated would accelerate osseointegration. Materials and Methods : Porous implants which were made by electric discharge were used in this study. Implants were anodized and hydrothermal treatment or HA sol-gel coating was performed. Hydrothermal treatment was conducted by high pressure steam at $300^{\circ}C$ for 2 hours using a autoclave. To make a HA sol, triethyl phosphite and calcium nitrate were diluted and dissolved in anhydrous ethanol and mixed. Then anodized implant were spin-coated with the prepared HA sols and heat treated. Samples were soaked in the Hanks solution with pH 7.4 at $37^{\circ}C$ for 6 weeks. The microstructure of the specimens was observed with a scanning electron microscope (SEM), and the composition of the surface layer was analyzed with an energy dispersive spectroscope (EDS). Results : The scanning electron micrographs of HA sol-gel coated and hydrothermal treated surface did not show any significant change in the size or shape of the pores. After immersion in Hanks' solution the precipitated HA crystals covered macro- and micro-pores The precipitated Ca and P increased in Hanks' solution that surface treatment caused increased activity. Conclusion : This study shows that sol-gel coated HA and hydrothermal treatment significantly enhance the rate of HA formation due to the altered surface chemistry.

• Fashion & Textile Research Journal
• /
• v.20 no.4
• /
• pp.422-428
• /
• 2018

In this study, we developed honeycomb pads using foam and polymer gel and verified the impact protection performance of pads for the development of a fall protection pants for elderly women aged 65 and over who have a high risk of fracture due to falls. The results are as follows; In the first experiment, the impact protection performance was evaluated for four honeycomb pad samples (CR foam, EPDM foam, hardness 15 polymer gel, and hardness 30 polymer gel) manufactured to a thickness of 5 mm using a single material. When the force of about 10757N was applied to the specimens, all four pads reduced the impact force to 3100N or less. Polymer gels showed better protection than foam materials. In the second experiment, the thickness of the protective pad was set to 8 mm in order to improve the shock absorbing performance of the protective pad. As a result of evaluating the impact protection performance of the foam single pad and foam gel composite pad, the impact absorbing performance of the foam single pad was better. Finally, four kinds of protection pads were made by assigning the foam single pad and the foam gel composite pad to pants type and underwear type respectively. The pad thickness of the main protection area was set to 8 mm to enhance the protection, and gradually decreased to 5mm and 3mm toward the edge to improve the appearance and fit.

• Journal of the Korean Ceramic Society
• /
• v.40 no.12
• /
• pp.1189-1196
• /
• 2003

Ferroelectric B $i_{3.25}$L $a_{0.75}$ $Ti_3$ $O_{12}$ (BLT) solution was synthesized by sol-gel process. BLT thin films were deposited on Pt/Ti $O_2$/ $SiO_2$/Si substrates by spin-coating. In this experiments, Bi(TMHD)$_3$, La(III)2-Methoxyethoxide, and Ti(IV) i-propoxide were used as starting materials, which were dissolved in 2-Methoxyethanol. Rapid Thermal Annealing (RTA) was used to promote crystallization of BLT thin films. The thin films with RTA process were compared with those with non-RTA process on electrical properties. After RTA process, the remanent polarization value (2Pr) of BLT thin films annealed at 72$0^{\circ}C$ was 20.46 $\mu$C/$\textrm{cm}^2$ which was approximately 27% higher than that of non-RTA process at 5 V.

• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.442-447
• /
• 2007

In order to improve the surface hardness of transparent plastic films, organic-inorganic hybrid coating solutions were synthesized by the sol-gel method. The coating solutions were prepared by adding GPTMS (glycidoxypropyl trimethoxysilane) to a colloidal silica (12 nm) suspension. PC(polycarbonate) substrates were dipped into the coating solutions and dried at room temperature for 10 min before being cured at $80^{\circ}C$ for 30 min. The effect of the solution pH and GPTMS content was investigated on the properties of coating films. The pencil hardness and adhesion to substrates of the coating films, prepared at acidic condition (pH 4), showed better properties than those at neutral or basic conditions. Also, the pencil hardness and adhesion to substrates of the coating films increased with increasing GPTMS content.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.2
• /
• pp.622-628
• /
• 2013

Nanocrystalline spinel lithium manganese oxide ($LiMn_2O_4$) powders with narrow-size-distribution, pure-phase particles, and high crystallinity with an average crystallite size of about 70 nm were synthesized at $600^{\circ}C$ for 6 h in air by freeze drying method. Spinel $LiMn_2O_4$ is also prepared by sol-gel using citric acid as a chelating agent. The influence of different parameters such as pH conditions, solvent, molar ratio of citric acid to total metal ions, calcination temperature, starting material on the structure, morphology and purity of this oxide was investigated. The results of sol-gel method show that pure $LiMn_2O_4$ with average crystallite size of about 130 nm can be produced from nitrate salts as starting materials at $800^{\circ}C$ for 6 h in air. The optimum pH and molar ratio of chelating agent to total metal ions are $4{\leq}pH{\leq}6$ and 1.0, respectively. A possible mechanism on the formation of the nanocrystallines synthesized by sol-gel was also discussed. At the end a comparison of the differences between two methods was made on the basis of x-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) tests.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.467-471
• /
• 2021

A ladder-like polysilsesquioxane (LPMA64) functionalized with a crosslinkable group was synthesized and used for the preparation of organic-inorganic hybrid gel polymer electrolytes through a thermal crosslinking process of the liquid electrolytes. A small weight percent of LPMA64 polymer crosslinker (5 wt%) was able to form a well-developed network structure, resulting in good dimensional stability with high ionic conductivity. The lithium-sulfur batteries fabricated with organic-inorganic hybrid gel polymer electrolytes exhibited stable C-rate and cycling performance with excellent Coulombic efficiency due to the alleviated lithium polysulfide shuttling effect during prolonged cycling. The result demonstrates that the organic-inorganic hybrid gel polymer electrolytes could be a promising candidate electrolyte for application in lithium-sulfur batteries.

• Nuclear Engineering and Technology
• /
• v.53 no.1
• /
• pp.188-198
• /
• 2021

A modern approach to nuclear energy involves reprocessing like transmutations of spent nuclear fuel products to reduce their radiotoxicity and time needed for their storage. For this purpose, they are immobilized in inert matrices made of zirconia and can be "burned" in fast neutron reactor or Accelerator Driven System. These matrices in spherical form can be obtained by sol-gel process. The paper presents a method of microspheres fabrication based on the combined Complex Sol-Gel Process and double extraction process consisting in the preparation of zirconium-ascorbate sol and simultaneous extraction of water and nitrates. The procedure allows obtaining gel microspheres with a diameter of 50 ㎛, which after heat treatment are processed into the final product. The synthesis of zirconia microspheres with Yttrium by internal gelation process is well known for over a decade now. However, the explanation and characterization of synthesis of such material by extraction of water process is rarely found. Parameters such as: pH, viscosity, shape, sphericity and crystal structure have been determined for synthesized products and semi-products. In addition, preliminary research consisting in irradiation of the obtained materials in fast and thermal neutron flux was carried out. The obtained results are presented and described in this work.