• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.840-844
• /
• 2003

The main objective of this investigation is to improve the photoluminescent of $Zn_{2}SiO_{4}:Mn$ phosphors prepared by the sol-gel technique. We try to use adding a new co-dopan such as Cr and Ti. The calcination temperature of sol-gel technique(1100 $^{\circ}C$) was lower than that of the solid state reaction (1300 $^{\circ}C$). Under 147nm excitation, the maximum emission intensity was obtained when the concentration of Cr and Ti was 0.1mol% with respect to $Zn_{2}SiO_{4}:Mn$. In order to study the effect of co-dopant, the content of Mn and the ratio of water to TEOS were fixed at 2mol% and 36:1, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.163-167
• /
• 2013

Aluminum doped zinc oxide (AZO) thin films have been prepared on the glass substrates (Corning 1737) by sol-gel dip-coating method employing zinc acetate and aluminum chloride hexahydrate for the transparent conducting oxide (TCO) applications. 1 at% Al was doped to the ZnO thin films. The effects of post-heating temperature on the crystallization, optical and electrical properties of the AZO films have been investigated. Experimental results showed that post-heating temperature affected the microstructure, electrical resistance, and optical transmittance of the AZO films. From the X-ray diffraction analysis, all films have hexagonal wurtzite crystal structure. Optical transmittance spectra of the AZO films exhibited transmittance higher than about 80% within the visible wavelength region and the optical direct band gap ($E_g$) of these films was increased with increasing post-heating temperature. A minimum resistivity of $2.5{\times}10^{-3}{\Omega}cm$ was observed at $650^{\circ}C$.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.1
• /
• pp.91-95
• /
• 2014

(F,Ga) co-doped ZnO thin film on glass substrate was fabricated via a simple non-alkoxide sol-gel spin-coating. Contrary to the F single doped ZnO thin film, the (F,Ga) co-doped thin film showed a significant reduce in electrical resistivity after a second post-heat-treatment in reducing environment. The resulting decrease in electrical resistivity with Ga co-doping is considered to be resulted from the increases both carrier density and mobility. The optical transmittance of the (F,Ga) co-doped thin film in the visible range showed higher transmittance with Ga co-doping compared with F single doped ZnO thin film.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.29-30
• /
• 2019

The indoor air quality of modern people who work indoors more than 80 percent a day has also become a very important factor in their lives. But most indoor air quality is highly polluted due to energy conservation and lack of ventilation. This can lead to pneumonia, asthma and even lung cancer, which can be fatal to children, the elderly and the elderly. Indoor pollutants are caused by boards, wallpaper, paint, etc. used in interior By producing indoor finishing materials using active alumina gel, which is used as dehumidifier, indoor pollutants will be reduced and the possibility of developing respiratory diseases and lung cancer will be reduced.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.66-67
• /
• 2020

The synthesis of stearic acid composite phase change material (PCM) was investigated and the samples produced were characterized for use in latent heat storage, using a simple chemical sol-gel process. The PCM was encapsulated to tetraethyl orthosilicate by various preparation ratios of stearic acid (5, 10, 15, 20, 30 and 50%). Fourier transformation infrared spectroscope (FT-IR) and X-Ray diffraction (XRD) were performed to determine the chemical structure and crystalloid phase of the microencapsulated PCM. SATEOS1 (5%) shows the best proportion for the PCM. With the presence of stearic acid as core materials and SiO2 as the supporting materials, it does not show any chemical reaction between both of them. SATEOS1 shows promising potential for thermal energy storage as it shows a better encapsulation efficiency and good thermal stability.

• Electrical & Electronic Materials
• /
• v.7 no.6
• /
• pp.496-503
• /
• 1994

In recent years Sol-Gel processing provides an interesting alternative method for the fabrication of ferroelectric thin layers and powder. PZT powder was prepared from an alkoxide-based solution by a Sol-Gel method. Gelation of synthesized complex solutions, microstructure, thermal analysis and crystallization behaviors of the calcined powder were studied in accordance with a water content and a catalyst. Especially gelation and crystallization behavior were analysed with the change of pH. The gelation time decreased as the pH of the mixed solution increased. For PZT powder with 650.deg. C heat treatment, 100% perovskite phase was formed by using either acidic or basic catalyst. By using either acidic or basic catalyst, we were able to get very fine powders of uniform shape with an average particle size of 0.8-1.mu.m.

• Journal of the Korean Society of Safety
• /
• v.13 no.1
• /
• pp.85-91
• /
• 1998

Sol-gel derived silica films were prepared by dip-coating onto polymethylmethacylate with Tetraethoxysilane(TEOS) as starting materials. Film properties such as viscosity and thickness were investigated as a function of dip speed, waterprecursor ratio, sol aging time. IR spectra of the gel films prepared from TEOS at various R are given. At small values of R the absorption peaks assignable to C-H vibration in $-OC_2H_5$ groups are observed around 3000 and 1500-1300 $cm^{-1}$. These bands indicate that the -$-OC_2H_5$ groups are retained in the gel at small values of R because of incomplete hydrolysis of TEOS. Film behaviour was interpreted in terms of the dependence of hydrolysis and condensation rates on the interplay between sol pH and waterprecursor ratio. Film thickness was found to increase by approximately a factor of two as waterprecursor ratio increased from two to six. Film thickness also increased with sol prepolymerization time. Surface quality was correlated with processing conditions.

• Molecular & Cellular Toxicology
• /
• v.4 no.2
• /
• pp.100-105
• /
• 2008

Biochips are a powerful emerging technology for biomedical, environmental applications. Especially, making use of bioseonors in the evaluation of toxicity becomes increasingly important. For biosensor as a toxicity detection, biomolecules like antibodies or aptamers have been developed to specifically capture the toxic target molecules. In addition, the development of optimal chip materials capable of maintaining the activity of embedded biomolecules such as proteins or aptamers has proven challenging. Here, using sol-gel materials, new chip material, whose ability for immobilizing the embedded aptamers and maintaining the ability of embedded aptamers is optimal, was searched. We used sol-gel formulation screening methods previously developed and found the best formulation which shows high sensitive and specific interactions of aptamers. This study results will support the technological advancement for diagnosis and environmental sensor.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.679-684
• /
• 2009

Phosphors of $Eu^{2+}$ doped alkaline earth aluminates MA$l_2O_4:Eu^{2+}$ (M=Sr, Ba, Ca) have been prepared by sol-gel process and their characterization of photoluminescence and photocurrent properties have been performed. The phosphors prepared by sol-gel process, due to its advantage of better homogeneity and low synthetic temperature, was synthesized as single phases at lower temperature than the solid-state process; $800{\sim}1000{^{\circ}C}$ for 6 h under mild reduction atmosphere (Ar- 3% $H_2$). It was confirmed that SrA$l_2O_4:Eu^{2+}$ composition revealed the most excellent properties in the brightness and photocurrent.

• Korean Journal of Materials Research
• /
• v.30 no.10
• /
• pp.533-541
• /
• 2020

UO₂ kernels, a key component of fuel elements for high temperature gas cooled reactors, have usually been prepared by sol-gel methods. Sol-gel processes have a number of advantages, such as simple processes and facilities, and higher sphericity and density. In this study, to produce 900 ㎛-sized UO₂ particles using an external gelation process, contact length extension of the NH₃ gas of the broth droplets pass and the improvement of the gelation device capable of spraying 14 M-NH₄OH solution are used to form 3,000 ㎛-sized liquid droplets. To produce high-sphericity and high-density UO₂ particles, HMTA, which promotes the gelation reaction in the uranium broth solution, is added to diffuse ammonium ions from the outside of the gelation solution during the aging process and generate ammonium ions from the inside of the ADU gel particles. Sufficient gelation inside of ADU gel particles is achieved, and the density of the UO₂ spheres that undergo the subsequent treatment is 10.78 g/㎤; the sphericity is analyzed and found to be 0.948, indicating good experimental results.