• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.679-686
• /
• 2013

The reduction unit is one of the most important components in railway cars, due to the transmission of torque from the motor to the wheels. Faulty reduction gears in high-speed trains result from excessive wear on the gear or damage to the gear. These types of gear defects have a significant effect on high-speed rail operation and safety; thus, a diagnosis system for the reduction unit is needed. Vibration diagnosis technology is one of the most effective diagnostics. In this paper, the vibration parameters of a reduction unit were evaluated during a driving-gear test and a full-vehicle test, using kurtosis and the crest factor. These tests were performed under normal operating conditions; a specimen tester was used to diagnose problems in defective gears.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1057-1067
• /
• 2010

Vibration and noise analysis as well as strength of gear teeth, gear profile design are considered in order to develop the multi-gear train devices of synchro system for the guns of a warship. A new approach to the critical speed calculation of practical industrial multi-mesh geared system is presented. A transfer matrix model based on Hibner's branch method is developed and the natural properties of the branched rotor system are calculated with using the ${\lambda}$-matrix formulation. A Campbell diagram, in which the excitation sources caused by the mass unbalance of the rotors and the transmitted errors of the gearing are considered, shows that, at theoperating speed, there are not the critical speed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.3
• /
• pp.308-314
• /
• 2016

This paper proposes design guidances for noise reduction of a bank teller cash recycler(TCR). The operating noise of a TCR is required to be reduced because it bothers bank tellers and customers. The operating noise from a TCR is measured and the most influential driving system is examined. To find the main sources of the noise, the frequency spectra are analyzed by comparing with excitation frequencies of the driving system. From the analysis results, we reveals that the main sources of the noise are gear mesh frequency of a certain gear train and its side band frequencies, which is attributed by vulnerable support condition. Consequently, to reduce the operating noise, the structural modification for the gear train support is suggested and its effectiveness for the noise reduction is confirmed experimentally.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.314-319
• /
• 2005

The rubber tire type AGT vehicles had been developed in a few years. And testing are finished on the test track. The extremely differ from heavy train with iron wheels are current collect type and wheel's characteristic. Analysis the current collect gear dynamic with vehicle dynamic and reduce the exchange rate shoes of current collect gear's.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.448-452
• /
• 2008

2-stroke marine diesel engine has generally one exhaust valve and three fuel injection nozzle which are key component for engine's performance and combustion. Fuel injection and exhaust valve driving system are driven by rotating of camshaft. Rotation of crank shaft drives the cam shaft through gear train that is composed of $3{\sim}4$ gear wheels. Gear column supporting the gear wheel has to bear against the dynamics forces by engine running as well as gearing forces. In this paper, structural analysis for engine structure and fatigue strength assessment of welded joint is shown. Repeatedly full cyclic simulation during one cycle is performed to investigate the structural behavior of engine. Fatigue analysis is carried out based on IIW using submodeling technique to obtain more detailed stress distribution.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1775-1780
• /
• 2003

A hybrid finite element analysis was used to analyze the influence of ring gear rim thickness and spline number on the static properties of an epicyclic gear system with manufacturing errors. Both of these parameters affected the bearing force and critical stress. The effect of changes in the rim thickness on the load sharing between the gears depended on the type of manufacturing error. Ring flexibility improved the load sharing between planetary gears only in systems with planet tooth thickness or planet tangential errors; for other types of error, ring flexibility worsened the load sharing. To improve load sharing, rim thickness and spline number should be controlled within a specific range. The effect of the ring gear boundary condition was more apparent in a system with errors than in a normal system.

• Journal of Drive and Control
• /
• v.17 no.1
• /
• pp.1-12
• /
• 2020

This study was to develop a simulation model of a compound planetary gear reducer for the final driving shaft using a gear analysis software (KISSsoft, Version 2017, KISSsoft AG, Switzerland). The aim of this study is to analyze transmission error and the tooth load distribution through micro-geometry using the simulation model. The tip and root relief were modified with Micro-geometry in the profile direction, and crowning was modified with Micro-geometry in the lead direction. The transmission error was analyzed using the PPTE (Peak to Peak Transmission Error) value, and the tooth load distribution was analyzed for the concentrated stress on the tooth surface. As a result of modifying tip and relief in the profile direction, the transmission error was reduced up to 40.7%. In the case of modifying crowning in the lead direction, the tooth load was more evenly distributed than before and decreased the stress on the tooth surface. After modifying the profile direction for the 1st and 2nd planetary gear train, the bending and contact safety factors were increased by 31.7% and 17%, and 18.3% and 12.5% respectively. Moreover, the bending and safety factors after modifying lead direction were increased by 59.5% and 32.7%, respectively for the 1st planetary gear train, and 59.6% and 43.6%, respectively for the 2nd planetary gear train. In future studies, the optimal design of a compound planetary gear reducer for the final driving shaft is needed considering both the transmission error and tooth load distribution.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.694-701
• /
• 2013

The gear-reduction units of Korean high-speed trains consist of a motor reduction unit, an axle gear box reduction unit, and a tripod joint shaft. A reduction gear unit is a gearbox used to reduce the rotational speed of the input shaft to a slower rotational speed on the output shaft. This reduction in output speed helps to increase torque. Defective reduction gear units in high-speed trains are caused by damage to the gear or by gear fatigue. To diagnose potential problems, it is important to know the vibration characteristics of the reduction gear units. In this study, we analyzed the vibration characteristics of reduction gears under various conditions. The test setup included a full-scale test rig to evaluate reduction gear under both normal and extreme operating conditions.

• Journal of Convergence for Information Technology
• /
• v.12 no.2
• /
• pp.142-148
• /
• 2022

In this paper, the weight reduction design of the yaw gearbox for wind turbine was performed through the finite element analysis method, and the stability was checked by performing the critical speed analysis. The weight reduction product can improve engine efficiency, save parts materials, and earn economic benefits. The yaw gearbox is lightweighted with the goal of achieving a safety rate of 1.3 or higher for wind turbine as indicated by IEC61400-1. In order to reduce the weight of the carrier, a topology optimization method was performed. The safety factor was verified by performing finite element analysis on the carrier. In addition, the housing and carrier were modeled using the finite element method, and the gear train was modeled using MASTA. For the yaw gearbox, the housing and carrier FE model and the gear train model were connected by the partial structural synthesis method to perform the rotational vibration analysis. Vibration excitation sources are mass unbalance and gear mesh frrequemcy, and as a result of the critical speed analysis, it was found that there was no resonance within the operating speed range.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.7
• /
• pp.770-777
• /
• 2012

This paper deals with the design and modal characteristics analysis of a drive-train for a paralleltype hybrid electric vehicle (HEV). The function of the drive-train system (DTS) in the HEV combines or divides the torque and velocity from the internal combustion engine along with the induction motor. The system consists of a compound planetary gear and unit's electromagnetic clutch to provide the operation modes such as Engine Only (EO), Electric Vehicle (EV), and Hybrid Electric Vehicle (HEV) modes. In order to investigate the characteristics of the velocity and torque flow for the system, dynamic models of the HEV with DTS are derived from the prototype DTS. The performance of the derived dynamic models is evaluated by both computer simulations and experiments according to each mode.