• 드라이브 ㆍ 컨트롤
• /
• 제13권4호
• /
• pp.45-51
• /
• 2016

The power train of a hydro-mechanical, continuously variable transmission for forklifts makes use of hydro-static units, hydraulic multi-wet disc brakes & clutches, and complex helical & planetary gears. The complex helical & planetary gears are very important parts of the transmission because of a strength problem. In the present study, we calculated the specifications of the complex helical & planetary gear train, and analyzed the gear bending and compressive stresses of the gears. It is necessary to analyze the gear bending and compressive stresses thoroughly for optimal design of the complex helical & planetary gears with respect to cost and reliability. In this paper, we analyze the actual gear bending and compressive stresses of complex helical & planetary gears using the Lewes & Hertz equation, and we also verify the calculated specifications of the complex helical & planetary gears by evaluating the results of the data of allowable bending and compressive stress using the Stress vrs Number of Cycles curves of gears.

• 한국안전학회지
• /
• 제12권4호
• /
• pp.39-46
• /
• 1997

This study describes a computer aided design system on involute gear for power transmition. Input data for gear design are pressure angle $20^{\circ}$, transmitted power, gear volume, gear ratio, addendum ratio of rack, dedendum ratio of rack, edge radius of rack, allowable contact stress and allowable bending stress etc. Bending strength contact strength and scoring are considered as the design constraints. Method of optimization developed this study. The developed gear design system can design the optimized gear that minimize the number of pinion teeth with face tooth.

• 한국산업융합학회 논문집
• /
• 제21권4호
• /
• pp.159-165
• /
• 2018

In electric agricultural machine a reduction gear is needed to convert the high speed rotation motion generated by DC motor to lower speed rotation motion used by the vehicle. The reduction gear consists of several spur gears. Spur gears are the most easily visualized gears that transmit motion between two parallel shafts and easy to produce. The modelling and simulation of spur gears in DC motor reduction gear is important to predict the actual motion behaviour. A pair of spur gear tooth in action is generally subjected to two types of cyclic stress: contact stress and bending stress. The stress may not attain their maximum values at the same point of contact fatigue. These types of failure can be minimized by analysis of the problem during the design stage and creating proper tooth surface profile with proper manufacturing methods. To improve its life expectation in this study modal and stress analysis of reduction gear is simulated using ANSYS workbench based on finite element method (FEM). The modal analysis was done to understand reduction gear deformation behaviour when vibration occurs. FEM static stress analysis is also simulated on reduction gear to simulate the gear teeth bending stress and contact stress behaviour.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.92-97
• /
• 2004

The aim of this study is to estimate the strength of injection molded plastic stepped gear. We considered stepped gear as plate model which are fixed by two edges. While, on the other sides are free. Normal gear is calculated by Lewis formula which can be derived quite simply from the equation for the stress at the root of a cantilever beam. Stress ratio(step factor) is represented for the ratio of the bending stress of normal and the bending stress of stepped gear, and it is plotted by face width factor. This study is propose the step factor added in Dupont equation which are strength estimation of step gear

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 2002년도 추계 학술논문발표회 논문집
• /
• pp.263-269
• /
• 2002

Design method for Involute bevel gears is developed. The developed gear design system can design the optimized gear that minimize the number of pinion teeth with face tooth. Method of optimization is MS(matrix search) which is developed from this study. Design variables are pressure angle 20, transmitted power, gear volume, gear ratio, allowable contact stress and allowable bending stress, etc. Design method developed this study can bd applide to the plane, machine tools, automobiles.

• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.97-103
• /
• 2008

In general, the strength of gears is calculated using the formula of AGMA or JGMA. But these formula can not be applied directly to the strength calculation of the rack and pinion of steering gear assay, because of complex tooth and contact shapes. So Lewis bending stress and Hertzian contact stress formula are generally used for the design of rack and pinion of steering gear assay. But these formula do not also give the exact stress of rack and pinion. In this paper, comparing the finite element analysis results and the experimentally measured values, it is shown that the finite element modeling technique of the rack and pinion of steering assay is reasonable.

• 한국기계가공학회지
• /
• 제11권2호
• /
• pp.55-59
• /
• 2012

This study performs the bending and contact stress analyses for a pair of mating gears during rotation. The interested gears are used for a railway reducer. In general, the railway reducer needs high speed rotation, which leads to a large gear ratio. Thus, it is not easy to apply finite element method to investigate the strength performance, since the size of a gear is much larger than that of a pinion. In this study, the bending and contact stresses determined from FEM are compared with the values determined from the ISO code.

• 농업과학연구
• /
• 제43권3호
• /
• pp.441-449
• /
• 2016

Agricultural tractors are designed using the empirical method due to the difficulty of measuring precise load cycles under various working conditions and soil types. Especially, directly drives various tractor implements, the power take off (PTO) gear. Therefore, alternative design methods using gear design software are needed for the optimal design of tractors. The objective of this study is to simulate fatigue life of the PTO gear according to the operating point of the tractor engine. The PTO gear was made with SCr415 alloy steel with carburizing and quenching treatments. The fatigue life of the PTO gear was simulated by using bending and contact stress according to the torque of the load levels. The PTO gear simulation was conducted by the KISSsoft commercial software for gear analysis. Bending and contact stress were calculated by the ISO 6336:2006 Method A and B. The simulation of fatigue life was calculated by the Miner's cumulative damage law. The total fatigue life of tractors can be estimated to 3,420 hours; thus, 3,420 hours of fatigue life were used in the simulation of the PTO gear of tractors. The main simulation results showed that the maximum fatigue life of the PTO gear was infinite fatigue life at maximum engine power. Minimum fatigue life of the PTO gear was 19.61 hours at 70% of the maximum engine power. Fatigue life of the PTO gear changed according to load of tractor. Therefore, tractor work data is needed for optimal design of the PTO gear.

• 한국정밀공학회지
• /
• 제14권9호
• /
• pp.61-67
• /
• 1997

Hardened layer and compressive residual stress created by carburized treatment effect on bending strength of gear massively. Also, shot peening treatment improves the strength of carburized gear as it does the hardness and residual stress of surface layer. In these days shot peening techniques are welcomed as one of physical improvement ways around the surface of materials. It is used widely because qualitative analysis of shot peening has become possible and surface treatment can be done with very little costs comparaed to other surface improvement methods. Therefore this study investigates the effect of shot peening in surface shape and bending fatigue strength after doing many kinds of shot peening treatments, then doing fatigue test and also explained characteristics of shot peening gear.

• 오토저널
• /
• 제6권3호
• /
• pp.45-54
• /
• 1984

Bending strength of an internal gear tooth is discussed as tooth form factor taking into account the actual stress magnitude. Stress analysis was carried out by the finite element method(FEM) for the calculation of tooth form factor of an internal gear. This paper also investigated the influences of number of teeth and addendum modification coefficient of the internal gear and the influences of number of teeth, addendum modification coefficient, pressure angle, radius of rounding of tooth tip, and bottom clearance coefficient of the pinion-shaped cutter on tooth form factor of internal gear. Generalizing the resultant data, a simple formula for the tooth form factor of an internal gear was derived for the calculation of tooth bending strength of an internal gear.