• Journal of Advanced Marine Engineering and Technology
• /
• v.8 no.2
• /
• pp.25-38
• /
• 1984

Since the energy shock in 1973, there have been wide studies for the developments of the alternative energy source, the rationalization of the energy utilization and the energy economy because of the recognition of the limitation of energy source all over the world. This study is experimentally examined in and compared with the engine performance of output, torque and fuel consumption rate, and the exhaust emissions with the change of engine rmp in the cases of using water-gashol blends, gashol and gasoline as a fuel in a conventional 4 cycle 4 cylinder gasoline engine. In the case of using water-gashol blends, it is installed by the exhaust manifold pipe into the intake manifold, and water is injected from nozzle fitted up the air horn of the carburetor. The results are obtained as follows; 1. In the case of an addition with water, the engine output and the torque are little difference with the case of gasoline. 2. The fuel consumption rate is decreased as compared with the case of gasoline. Especially, the decrease in quantity is remarkable at the low rpm. 3. The exhaust emissions are remarkably decreased as compared with the case of gasoline. Especially, decreases of CO and HC in quantity are remarkable at the low rpm, and a decrease of No/sub x/ in quantity is remarkable at the high rpm. 4. There is a moderate condition of operation because the producing factors of NO/sub x/ and CO, HC are contrary to each other.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.3
• /
• pp.178-185
• /
• 2006

This paper investigates the steady-state combustion characteristics of the Homogeneous charge compression ignition(HCCI) engine with variable valve timing(VVT) and dimethyl ether(DME) direct injection, to find out its benefits in exhaust gas emissions. HCCI combustion is an attractive way to lower carbon dioxide($CO_2$), nitrogen oxides(NOx) emission and to allow higher fuel conversion efficiency. However, HCCI engine has inherent problem of narrow operating range at high load due to high in-cylinder peak pressure and consequent noise. To overcome this problem, the control of combustion start and heat release rate is required. It is difficult to control the start of combustion because HCCI combustion phase is closely linked to chemical reaction during a compression stroke. The combination of VVT and DME direct injection was chosen as the most promising strategy to control the HCCI combustion phase in this study. Regular gasoline was injected at intake port as main fuel, while small amount of DME was also injected directly into the cylinder as an ignition promoter for the control of ignition timing. Different intake valve timings were tested for combustion phase control. Regular gasoline was tested for HCCI operation and emission characteristics with various engine conditions. With HCCI operation, ignition delay and rapid burning angle were successfully controlled by the amount of internal EGR that was determined with VVT. For best IMEP and low HC emission, DME should be injected during early compression stroke. IMEP was mainly affected by the DME injection timing, and quantities of fuel DME and gasoline. HC emission was mainly affected by both the amount of gasoline and the DME injection timing. NOx emission was lower than conventional SI engine at gasoline lean region. However, NOx emission was similar to that in the conventional SI engine at gasoline rich region. CO emission was affected by the amount of gasoline and DME.

• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.4
• /
• pp.373-381
• /
• 2012

To determine the performance characteristics of motorcycle engine using biogas for practical use, the intake system of a 110 cc motorcycle engine is properly modified to operate with biogas as a fuel. Biogas is a potentially renewable fuel for replacing gasoline in future, but it has high percentage of $CO_2$ that could lead to slow the burning rate of biogas-air mixture and cause instability in combustion. Thus, the performance characteristics of biogas-fueled motorcycle engines could be different from those of gasoline motorcycle engines. In this paper, the important parameters of performance characteristics (such as: power output, thermal efficiency, fuel consumption, exhaust emission,${\cdots}$) of biogas-fueled motorcycle engine are studied and estimated with change of engine speed and load. The obtained results when operating with biogas are used to compare with that of gasoline fuel under the same operating conditions. Engine speed in the experimental is changed from 1500 rpm (idle-mode) up to 3500 rpm by a step of 500 rpm. Engine load is changed from zero to maximum load with the help of an exciting voltage device from generator-type dynamometer. The experimental results show that the tested engine operated with richer biogas-air mixture than that of gasoline-air mixture under the same test conditions. Biogas-fueled engine gives a higher fuel consumption and lower thermal efficiency under the same power output. Brake thermal efficiency of biogas engine is found to be about 3% lower than gasoline-fueled motorcycle engine for whole range of speed. Exhaust emission of biogas-fueled motorcycle engine (such as: CO, HC) is found to be lower than the limitation level of the emission standards of Vietnam for motorcycle engines (CO <4.5% HC <1200 ppm).

• 한국기계연구소 소보
• /
• s.9
• /
• pp.7-20
• /
• 1982

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.5
• /
• pp.632-637
• /
• 2010

Natural gas, a fossil fuel contained mostly of methane, is one of the cleanest alternative fuels. It can be used in the form of compressed gas(CNG) or liquefied natural gas(LNG) to cars and trucks. And, dedicated natural gas vehicles are designed to run on natural gas only, while Bi-fuel vehicles can also run on gasoline or CNG, especially, bi-fuel can be defined as the simultaneous combustion of two fuels. In this study, converted gasoline marine system to CNG Bi-fuel system which is made up of injector, regulator, tank and ECU is converted. And estimated the fuel system and engine power compared the result with gasoline engine is estimated. As a result, CNG engine shows low exhaust emissions but maxium power is 7% reduced compared to gasoline engine.

• Journal of the Korean Institute of Gas
• /
• v.15 no.4
• /
• pp.33-38
• /
• 2011

The introduction of alternative fuels is beneficial to overcome the fuel shortage and reduce engine exhaust emissions. LPG and CNG are relatively clean fuel and considered as most promising alternative automotive fuels worldwide because of its emission reduction potential and lower fuel price compared to gasoline. Now a day’s adaptation of dual fuel approach is the growing as common trend. The two fuels can be successfully implemented with existing gasoline engine with little modification. The present study was done to analyze the performance and emissions analysis of a multi cylinder spark ignition engine fuelled with the benefits of CNG and LPG aseffective alternate automotive fuels by simply using them in an unmodified petrol engine. The test results indicate, the energy content of CNG and LPG is the most limiting factor in acceptance for fuel economy and performance reasons. Thermal efficiency was high for CNG lowest for gasoline and LPG between the two. BSFC, CO and HC were low and NOx was high for CNG and low for gasoline, LPG lies between the two.

• Journal of Power System Engineering
• /
• v.10 no.1
• /
• pp.19-24
• /
• 2006

This work treats a controlled auto-ignition (CAI) single cylinder gasoline engine, focusing on the extension of operating conditions. The fuel was injected indirectly into electrically heated inlet air flow. In order to keep a homogeneous air-fuel mixing, the fuel injector was water-cooled by a specially designed coolant passage. The engine performance and emission characteristics were investigated under the wide range of operating conditions such as 40 in the air-fuel ratio, 1000 to 1800 rpm in the engine speed, 150 to $180^{\circ}C$ in the inlet-air temperature, and $60^{\circ}$ BTDC in the injection timing. The ultra lean-burn with self-ignition of gasoline fuel by heating inlet air was achieved in a controlled auto-ignition gasoline engine. It could be also achieved that the emission concentrations of carbon monoxide, hydrocarbons and nitrogen oxide significantly reduced by CAI combustion compared with conventional spark ignition engines.

• Journal of ILASS-Korea
• /
• v.19 no.4
• /
• pp.221-226
• /
• 2014

This paper described the effect of split injections on the stability of combustion and emission characteristics in a direct injection gasoline engine at various operating conditions. In order to investigate the influence of direct injection gasoline engine, the fuel injection timing was varied direct fuel injection at various fuel pressure. The experimental apparatus consisted of GDI engine with 4 cylinder, EC dynamometer, injection control system, and exhaust emissions analyzer. The emission and combustion characteristics were analyzed for the fuel injection timing and fuel injection pressure strategies. It is revealed that CO and HC emissions are dramatically decreased at advanced injection timing. Also, engine performance is increased at increase fuel injection pressure.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.214-218
• /
• 1988

This paper suggests mathemathical engine model which can simulate generalized gasoline engine. Suggested engine model contains air/fuel inlet element, intake manifold, combustion, engine dynamics. In order to analyze a gasoline engine, physical characteristics of engine and steady state engine data should be controlled. In adaptation for abrupt change of circumstance or drive conditions, this model can analyze important physical phenomena in the intake manifold by computer simulation. This model can also evaluate statuses of drive under various working conditions precisely. Therfore, this model suggests basic datum to evaluate the engine system which are needed in designing and development of engine controller.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.101-107
• /
• 2019

This study conducted a simulation to observe the performance of a multi-turbocharged gasoline internal combustion engine for a high-altitude long-endurance unmanned aerial vehicle (HALE UAV). The WAVE 1-D engine simulation software from Ricardo was used for the engine system modeling and simulation. The specifications of a 2.4-L four cylinder gasoline engine from commercial vehicles and maps of commercial vehicle turbochargers were applied to the multi-stage turbocharged engine system model. Three turbochargers and intercoolers were installed in series for the appropriate intake of pressure for the gasoline engine at a high altitude of 60,000 ft. There was one wastegate for the turbochargers. The operability of the engine system was analyzed via this simulation model.