• Membrane and Water Treatment
• /
• v.8 no.1
• /
• pp.35-50
• /
• 2017

The theoretical membrane gas absorption module treatments in a hollow fiber gas-liquid membrane contactor using Happel's free surface model were obtained under countercurrent-flow operations. The analytical solutions were obtained using the separated variable method with an orthogonal expansion technique extended in power series. The $CO_2$ concentration in the liquid absorbent, total absorption rate and absorption efficiency were calculated theoretically and experimentally with the liquid absorbent flow rate, gas feed flow rate and initial $CO_2$ concentration in the gas feed as parameters. The improvements in device performance under countercurrent-flow operations to increase the absorption efficiency in a carbon dioxide and nitrogen gas feed mixture using a pure water liquid absorbent were achieved and compared with those in the concurrent-flow operation. Both good qualitative and quantitative agreements were achieved between the experimental results and theoretical predictions for countercurrent flow in a hollow fiber gas-liquid membrane contactor with accuracy of $6.62{\times}10^{-2}{\leq}E{\leq}8.98{\times}10^{-2}$.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.521-528
• /
• 2008

The micro-porous asymmetric PVDF hollow fiber membranes for gas-liquid contactor were prepared by the dry-jet wet phase inversion process and the characteristics of hollow fiber membranes were evaluated by the gas permeation method and scanning electron microscope. The chemical absorbent for removal of $SO_2$ gas was sodium hydroxide at bench scale hollow fiber membrane contactor. The experiments were performed in a counter-current mode of operation with gas in the shell side and liquid in the fiber lumen of the module to examine the effect of various operating variables such as concentration of absorbent, gas flow rate, L/G ratio and concentration of inlet $SO_2$ gas on the $SO_2$ removal efficiency using PVDF hollow fiber membrane contactor. Membrane mass transfer coefficient($k_m$) was calculated by mathematical modeling. The volumetric overall mass transfer coefficient increased with increasing the concentration of absorbent and L/G ratio. The increase of the absorbent concentration and L/G ratio not only provides more sufficient alkalinity but also decreases liquid phase resistance. The volumetric overall mass transfer coefficient increased with increasing gas flow rate due to decreasing the gas phase resistance.

• Membrane Journal
• /
• v.17 no.4
• /
• pp.345-351
• /
• 2007

In this research, by using the fluorine gas, the poly(ether sulfone) (PES), the polysulfone (PSf), and the poly-vinylidenefluoride (PVDF) membranes were modified to improve the performance of the optional Gas-Liquid Contactor The SEM, surface contact angle, XPS, and the water transmission minimum pressure test was performed in order to examine the characteristics of which is surface modified. As a result of looking into the surface morphology of from the SEM measurement, we could know that the roughness of the membrane surface increased as the fluorine processing time increased. $-CH_2$, and the perfluoro group of $-CH_3$ were chemically combined with the surface fluorine conversion film surface and the hydrophobicity was exposed to be increased. Moreover, we could know that as the surface fluorinated processing time increased from the surface contact angle and water transmission minimum pressure test, the measured value increased and the overall characteristics were improved.

• Membrane and Water Treatment
• /
• v.13 no.3
• /
• pp.147-166
• /
• 2022

Liquid-liquid membrane contactor (LLMC), a device that exchanges dissolved gas molecules between the two sides of a hydrophobic membrane through membrane pores, can be employed to extract ammoniacal nitrogen from a feed solution, which is transported across the membrane and accumulated in a stripping solution. This LLMC process offers the promise of improving the sustainability of the global nitrogen cycle by cost-effectively recovering ammonia from wastewater. Despite recent technological advances in LLMC processes, a comprehensive review of their feasibility for ammonia recovery is rarely found in the literature. Our paper aims to close this knowledge gap, and in addition to analyze the challenges and provide potential solutions for improvement. We begin with discussions on the operational principles of the LLMC process for ammonia recovery and membrane types and membrane configurations commonly used in the process. We then assess the performance of the process by reviewing publications that demonstrate its practical application. Challenges involved in the implementation of the LLMC process, such as membrane fouling, membrane wetting, and chemical requirements, are presented, along with discussions on potential strategies to address each. These strategies, including membrane modification, hybrid process design, and process optimization based on cost-benefit analysis, guide the reader to identify key areas of future research and development.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.8 no.1
• /
• pp.10-13
• /
• 1979

The study for bubbling phenomena to influence heat transfer in gas - liquid contactors. The sparged contactor is gaining importance for gas-liquid chemical reactions. In this paper, correlations between Reynolds number and heat transfer coefficient were studied and experimental expressions were also obtained over broth of areas, namely, laminar area and turbulent area respectively.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.4
• /
• pp.503-510
• /
• 2011

Ammonia in water which is toxic to human, its concentration is regulated below 0.5 mg/L in drinking water. Current study aimed to develop appropriate models for ammonia stripping using hollow fiber membrane contactor. Two different models were developed during the study. Model 1 was assumed only free ammonia ($NH_3$) transfer in stripping process, whereas the Model 2 was assumed with total ammonia ($NH_3+{NH_4}^+$) transfer. Ammonium chloride ($NH_4CI$), sodium hydroxide(NaOH) were used to make ammonia solution, which was concentration of 25 mg as N/L at a pH of 10.5. The experimental conditions were such that, the liquid flow was in tube-side in upward direction and t he gas flow was on shell-side in downward direction a t room temperature. The experimental and modeling results showed that marginal difference were observed at low gas flux. However the difference between the both models and experimental value were increased when the gas flux was increased. The study concludes that the Model 1 with free ammonia is more appropriate when both models were compared and useful in ammonia stripping process at low gas flux.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2008.05a
• /
• pp.110-113
• /
• 2008

• Membrane Journal
• /
• v.30 no.4
• /
• pp.269-275
• /
• 2020

In this study, CO₂ separation experiment was performed on a CH₄/CO₂ mixed gas using a ceramic hollow fiber membrane contactor (HFMC). In order to fabricate high-performance HFMC, experiments were conducted to manufacture high-permeability hollow fiber membranes, and the prepared hollow fiber membranes were evaluated through N₂ gas permeation experiments. HFMC for CH₄/CO₂ mixed gas separation was manufactured using the manufactured high-permeability hollow fiber membrane. In the experiment, mixed gas of CH₄/CO₂ (34.5% CO₂, CH₄ balance) and monoetanolamine (MEA) was used, and the effect of CO₂ removal efficiency on the flow rate of the absorbent was evaluated. The CO₂ removal efficiency increased as the liquid flow rate increased, and the CO₂ absorption flux also increased with the liquid flow rate.

• Membrane Journal
• /
• v.15 no.3
• /
• pp.187-197
• /
• 2005

A membrane contactor is a device that achieves liquid/liquid or gas/liquid mass transfer without dispersion of one phase within another. This is accomplished by passing the fluids on opposite sides of a microporous membrane. This approach offers a number of important advantages over conventional dispersed phase contactors, including absence of emulsions, no flooding at high flow rates, no unloading at low flow rates, and high interfacial area. This article provides a general review of membrane contactors, including operating principles and applications.

• Membrane Journal
• /
• v.17 no.4
• /
• pp.302-310
• /
• 2007

The effects of various system parameter on the absorption of sulfur dioxide into the absorbent liquid were investigated in a circulatory porous polymer membrane contactor. A feed gas and an absorbent used in the study were the gas mixture of air and $SO_2$ and the $Na_2SO_3$ aqueous solution, respectively. The separation of sulfur dioxide was measured in terms of the concentration of $Na_2SO_3$ absorbent, the concentration of sulfur dioxide, the feed flow rate, the absorbent velocity and the different membrane material. As the concentration of absorbent increased from 0.05 to 0.2 M, the removal efficiency increased from 74 to 100%. By increasing the concentration of sulfur dioxide from 700 to 2,500 ppm, the removal efficiency decreased from 100 to 75%. Also as the absorbent velocity increased from 2.5 to 15 mL/min, the removal efficiency increased from 85 to 100%. As the porosity of the membrane increased, the removal efficiency increased.