• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.445-446
• /
• 2005

This letter reports the fabrication of polycrystalline silicon thin-film transistors (poly-Si TFT) on flexible plastic substrates using amorphous silicon (a-Si) precursor films by sputter deposition. The a-Si films were deposited with mixture gas of argon and helium to minimize the argon incorporation into the film. The precursor films were then laser crystallized using XeCl excimer laser irradiation and a four-mask-processed poly-Si TFTs were fabricated with fully self-aligned top gate structure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.430-431
• /
• 2006

This letter reports the fabrication of polycrystalline silicon thin-film transistors (poly-Si TFT) on flexible plastic substrates using amorphous silicon (a-Si) precursor films by sputter deposition. The a-Si films were deposited with mixture gas of argon and helium to minimize the argon incorporation into the film. The precursor films were then laser crystallized using XeCl excimer laser irradiation and a four-mask-processed poly-Si TFTs were fabricated with fully self-aligned top gate structure.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.2
• /
• pp.212-216
• /
• 1999

SiC(3C) photodiodes (PDs) were fabricated on p-type Si(111) substrates using chemical vapor deposition (CVD) technique by pyrolyzing tetramethylsilane (TMS) with $H_{2}$ carrier gas. Electrical properties of SiC(3C) were investigated by Hall measurement and current-voltage (I-V) characteristics. SiC(3C) layers exhibited n-type conductivity. Ohmic contact was formed by thermal evaporation Al metal through a shadow-mask. The optical gain $(G_{op})$ of the SiC(3C)/Si PD was measured as a function of the incident wavelength. For the analysis of the photovoltaic detection of the Sic(3C) n/p PD, the spectral response (SR) has calculated by using the electrical parameters of the SiC(3C) layer and the geometric structure of the PD. The peak response calculated for properly chosen parameters was about 0.75 near 550 nm. We expect a good photoresponse in the SiC(3C) heterostructure for the wavelength range of 400~600 nm. The SiC(3C) photodiode can detect blue and near ultraviolet (UV) radiation.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.24 no.2
• /
• pp.229-237
• /
• 2014

Objectives: This study intends to determine the current status of management of personal protective equipment fume hoods in university laboratories. Methods: A walk-through survey of 402 labs in Gyeongbuk Province and Daegu Metropolitan City were carried out between May 2009 and July 2010. Respectively, 348 and 54 laboratories were examined in Gyeongbuk Province and Daegu. Results: In size, labs serving over 15,000 student made up the majority with 276(66.4%). In terms of major, engineering labs were the highest in number with 100(24.9%). As to personal protective equipment, a gas mask and a dust mask were available in 17.8% and 14.3% of the labs, respectively, but 68.9% of labs were equipped with protective goggles. Meanwhile, only 12.7% of labs had separate protective equipment storage boxes. About 60% of the labs had installed a fume hood, of which the average capture velocity was 0.37 m/sec. Conclusions: For toxic substances, the labs are obliged to provide personal protective equipment in in accordance with the Occupational Safety and Health Act. In addition, the capture velocity of fume hoods must be in strict compliance in order to prevent occupational diseases due to toxic chemicals.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.200-200
• /
• 2013

기존 메모리 반도체에 비교해 빠른 재생속도와 높은 집적도, 비휘발성 등의 특성을 가지는 MRAM (Magnetic Random Access Memory)은 DRAM, flash memory 등을 대체할 수 있는 차세대 기억 소자로서 CoFeB/MgO/CoFeB로 구성된 한 개의 MTJ (Magnetic Tunnel Junction)를 단위 메모리로 사용한다. 이 MTJ 물질들은 고밀도 플라즈마를 이용한 건식 식각공정시 Cl2, BCl3 등과 같은 chlorine 을 포함한 가스를 이용하여 왔으나 식각 후 sidewall에서 발생하는 부식과 식각 선택비 확보의 어려움 등으로 마스크 물질에 제약을 받고 소자 특성이 감소하게 되는 등의 문제가 있다. 따라서 이러한 식각 문제점을 해결하기 위한 대안으로 noncorrosive 가스인 CO/NH3, CH3OH, CH4 등을 이용한 MTJ 식각 연구가 진행되어 오고 있으며 이중 CO/NH3 혼합가스는 부식성이 없고 hard mask와의 높은 선택비를 가지는 기체로 CO gas에 NH3 gas를 첨가하게 되면 etch rate이 증가하는 특성을 보인다. 또한 rf pulse-biased power를 이용하여 이온의 입사를 시간에 따라 제어함으로써 pulse off time 때 etch gas와 MTJ 물질간의 chemical reaction을 향상시킬 수 있다. 따라서 본 연구에서는 CO/NH3 혼합가스를 이용하여 다양한 rf pulse-biased power 조건에서 MTJ 물질인 CoFeB, MgO와 hard mask 물질인 W을 식각 한 뒤 식각특성을 분석하였으며 MTJ surface의 chemical binding state, surface roughness 측정을 진행하였다. 식각 샘플의 측정은 Alpha step profiler, XPS (X-ray Photoelectron Spectroscopy), AFM (Atomic Force Microscopy)를 통해 진행되었다. Time-averaged pulse bias에서는 duty ratio가 감소할수록 etch rate의 큰 감소 없이 CoFeB/W, MgO/W 물질의 etch selectivity가 향상됨을 확인할 수 있었으며 pulse off time 구간에서의 chemical reaction 향상으로 인해 식각부산물의 재증착이 감소하고 CoFeB의 surface roughness가 감소하는 것을 확인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.162-162
• /
• 2014

최근 들어 wearable computing에 대한 수요가 증가하면서 flexible device에 대한 연구가 활발히 진행되고 있다. 하지만, flexible device를 구현하기 위해서는 기판의 damage를 줄이기 위한 저온공정, device life-time 향상을 위한 passivation, 와이어 본딩 등 다양한 문제들이 해결 되어야 한다. 이러한 문제들 중, polymer 기판과 금속간의 접착력을 향상시키기 위해서 많은 연구자들은 기판의 표면에 adhesive layer를 도포하거나 금속잉크의 solvent를 변화시키는 등의 연구를 진행해왔다. 종래의 연구는 기존 device를 대체 할 수 있을 정도의 생산성과 polymer 기판에 대한 열 적인 손상 이 문제가 되었다. 종래의 문제를 해결하기 위하여 저온공정, in-line system이 가능한 준 준 대기압 플라즈마를 사용하였다. 본 연구에서는 금속잉크를 Ink-jet으로 jetting하여 와이어 본딩 하는 과정에서 전도성 ink의 선폭을 유지시키고 접착력을 향상하기 위하여 준 대기압 플라즈마 공정을 이용하여 이러한 문제점을 해결하고자 하였다. Polymer 기판 표면에 roughness를 만들기 위해 대략 수백 nm 크기를 갖는 graphene flake를 spray coating하여 마스크로 사용하고 준 대기압 플라즈마를 이용하여 표면을 식각 함으로써 roughness를 형성시켰다. 준 대기압 플라즈마를 발생시키기 위해 double discharge system에서 6 slm/1.5 slm (He/O2) gas composition을 하부 전극에 흘려보내고 60 kHz, 5 kV 파워를 인가하였다. 동시에 상부 전극에는 30 kHz, 5 kV 파워를 인가하여 110초 동안 표면 식각 공정을 진행하였다. Graphene flake mask가 coating되어 있는 유연기판을 산소 플라즈마 처리 한 후 물에 3초 동안 세척하여 표면에 남아있는 graphene flake를 제거하고 6 slm/0.3 slm (He/SF6)의 유량으로 주파수와 파워 모두 동일 조건으로 110초 동안 표면 처리를 하였다. Figure 1은 표면 개질 과정과 graphene flake를 mask로 사용하여 얻은 roughness 결과를 SEM을 이용하여 관찰한 결과이다. 이와 같이 실험한 결과 ink와 기판간의 접촉면적을 늘려주고 접촉 각을 조절하여 Wenzel model 을 형성 할 수 있는 표면 roughness를 생성하였고 표면의 화학적 결합을 C-F group으로 치환하여 표면의 물과 접촉각 이 $47^{\circ}$에서 $130^{\circ}$로 증가하는 것을 확인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.127-127
• /
• 2011

We investigate the transparent TFTs using a transparent ZnSnO3 (ZTO)/Ag/ZTO multilayer electrode as S/D electrodes with low resistivity of $3.24{\times}10^{-5}$ ohm-cm, and high transparency of 86.29% in ZTO based TFTs. The Transparent TFTs (TTFTs) are prepared on glass substrate coated 100 nm of ITO thin film. On atomic layer deposited $Al_2\;O_3$, 50 nm ZTO layer is deposited by RF magnetron sputtering through a shadow mask for channel layer using ZTO target with 1 : 1 molar ratio of ZnO : $SnO_2$. The power of 100W, the working pressure of 2mTorr, and the gas flow of Ar 20 sccm during the ZTO deposition. After channel layer deposition, a ZTO (35 nm)/Ag (12 nm)/ZTO(35 nm) multilayer is deposited by DC/RF magnetron sputtering to form transparent S/D electrodes which are patterned through the shadow mask. Devices are annealed in air at 300$^{\circ}C$ for 30 min following ZTO deposition. Using UV/Visible spectrometer, the optical transmittances of the TTFT using ZTO/Ag/ ZTO multilayer electrodes are compared with TFT using Mo electrode. The structural properties of ZTO based TTFT with ZTO/Ag/ZTO multilayer electrodes are analyzed by high resolution transmission electron microscopy (HREM) and X-ray photoelectron spectroscopy (XPS). The transfer and output characterization of ZTO TTFTs are examined by a customized probe station with HP4145B system in are.

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.450-455
• /
• 2000

For further scaling down of the silicon devices, the application of low dielectric constant materials instead of silicon oxide has been considered to reduce power consumption, crosstalk, and interconnection delay. In this paper, the effect of $O_2/SF_6$ plasma chemistry on the etching characteristics of polyimide-one of the promising low-k interlayer dielectrics-has been studied. The etch rate of polyimide decreases with the addition of $SF_6$ gas due to formation of nonvolatile fluorine compounds inhibiting reaction between oxygen and hydrocarbon polymer, while applying substrate bias enhances etching process through physical attack. However, addition of small amount of $SF_6$ is desirable for etching topography. $SiO_2$ hard mask for polyimide etching is effective under $O_2$plasma etching(selectivity~30), while $O_2/SF_6$ chemistry degrades etching selectivity down to 4. Based on the above results, $1-2\mu\textrm{m}$ L&S PI2610 patterns were successfully etched.

• Tuberculosis and Respiratory Diseases
• /
• v.51 no.6
• /
• pp.585-589
• /
• 2001

Pneumoperitoneum, Pneumomediastinum, subcutaneous emphysema and a pneumothorax are some of the mechanical complications of bronchial asthma. The incidence of pneumoperitoneum during an attack of acute asthma is rare. The pathogenesis is free gas track from the overdistended alveoli, through the bronchovascular sheaths to the mediastinum. If the high pressure is maintained, air can escape retroperitoneally into the abdomen and burst into the peritoneal cavity. A 43-year-old woman was admitted due to a severe asthma attack. She was required endotracheal intubation and AMBU(air mask bag unit) ventilation. Immediately after these procedures, pneumoperitonewn, pnewnomediastinwn, and subcutaneous emphysema developed. She was treated with mechanical ventilation and medical therapy. The pneumoperitonewn was resolved after 27days. Here, we report this case with the review of the relevant literature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.448-448
• /
• 2010

Magnetic random access memory (MRAM) has made a prominent progress in memory performance and has brought a bright prospect for the next generation nonvolatile memory technologies due to its excellent advantages. Dry etching process of magnetic thin films is one of the important issues for the magnetic devices such as magnetic tunneling junctions (MTJs) based MRAM. CoFeB is a well-known soft ferromagnetic material, of particular interest for magnetic tunnel junctions (MTJs) and other devices based on tunneling magneto-resistance (TMR), such as spin-transfer-torque MRAM. One particular example is the CoFeB - MgO - CoFeB system, which has already been integrated in MRAM. In all of these applications, knowledge of control over the etching properties of CoFeB is crucial. Recently, transferring the pattern by using milling is a commonly used, although the redeposition of back-sputtered etch products on the sidewalls and the low etch rate of this method are main disadvantages. So the other method which has reported about much higher etch rates of >$50{\AA}/s$ for magnetic multi-layer structures using $Cl_2$/Ar plasmas is proposed. However, the chlorinated etch residues on the sidewalls of the etched features tend to severely corrode the magnetic material. Besides avoiding corrosion, during etching facets format the sidewalls of the mask due to physical sputtering of the mask material. Therefore, in this work, magnetic material such as CoFeB was etched in an ICP etching system using the gases which can be expected to form volatile metallo-organic compounds. As the gases, carbon monoxide (CO) and ammonia ($NH_3$) were used as etching gases to form carbonyl volatiles, and the etched features of CoFeB thin films under by Ta masking material were observed with electron microscopy to confirm etched resolution. And the etch conditions such as bias power, gas combination flow, process pressure, and source power were varied to find out and control the properties of magnetic layer during the process.