• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.143-148
• /
• 2004

The numerical analysis of the hard disk drive slider is presented. The pressure distribution was calculated using the finite element method. The generalized Reynolds equation was applied in order to include the gas rarefaction effect. The balance of the air bearing force and preload force was considered. The characteristics of the small vibrations near the equilibrium were studied using the perturbation method. Triangular mesh with variable element size was employed to model the two-rail slider. The flying height, pitching angle, rolling angle, stiffness and damping of the two-rail slider were calculated for radial position changing from the inner radius to the outer radius and for a wide range of the slider crown values. It was found that the flying height, pitching angle and rolling angle were increased with radial position while the stiffness and damping coefficients were decreased. The higher values of crown resulted in increased flying height, pitching angle and damping and decreased stiffness.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.55-62
• /
• 1996

Present study was undertaken to investigate the effects of composition ratio and temperature on the friction and wear of PTFE-polyimide composites under the atmosphere of nitrogen gas. The load range was 0.62-3.46 MPa, and the temperature range was room temperature and 200$^{\circ}$C. To mention some of the notable results, friction coefficient of PTFE 100% varied relatively little within the given load and temperature ranges. Polyimide 100% showed the lowest friction coefficient of 0.06 at 200$^{\circ}$C among all the experiments. PTFE 80%-polyimide 20% showed the lowest wear factors on the whole. Friction coefficient of PTFE 20%-polyimide 80% varied from the highest 0.35 to the lowest 0.09 among all the materials at room temperature, and showed almost the same lowest values with polyimide 100% at 200$^{\circ}$C. Suggestion of friction and wear mechanisms of the materials was tried to explain the observed phenomena including above mentioned results.

• Tribology and Lubricants
• /
• v.6 no.2
• /
• pp.60-67
• /
• 1990

최근 전자 및 광학 분야에 있어서의 눈부신 발전은 다면경 가공기나 초정밀 연삭기와 같은 초정밀 가공기계의 개발과 실용화에 힘입은 바 크다. 이러한 초정밀 가공기의 성능을 좌우하는 핵심 요소로서 추축계를 들수 있으며, 비교적 소형 경량의 공박물을 가공하는 기계의 주축용 베어링으로는 오일 베어링을 대신하여 공기 베어링이 점차 널리 사용되고 있다. 이러한 가공기에 많이 사용되는 외부 가압 공기 베어링은 동압 공기 베어링과는 달리, 외부에서 가압된 압축공기에 의하여 공기막을 형성하므로, 시동과 정지시 마멸이 없고 저속에서도 비교적 높은 하중 지지력을 얻을 수 있으며, 오일 베어링과 비교하여서는 발열이 적고 윤활제의 유출에 의한 오염의 위험이 없다는 특성외에 공기막에 의한 평균화 효과에 의하여 고정도의 운전이 가능하다는 장점이 있다. 본 연구에서는 점급기원의 가정하게 직접 수치해법을 사용하는 해석 프로그램을 작성하여, 무차원화된 설계 변수들에 대한 외부가압 공기베어링의 정$\cdot$동특성수들을 구하고자 한다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1058-1064
• /
• 2000

The analysis of dynamic behaviour of rotor system for the rolling piston type rotary compressor considering hydrodynamic force between motor rotor and stator is presented. In addition to considering other dynamic, loads such as large unbalance forces, gas force and bearing force, we consider the hydrodynamic force induced by the compressed fluid flow through the air gap between motor rotor and stator, and improve the analysis of vibration in rotary compressor. The Childs' method which based on Bulk-now and Hirs' turbulent lubrication model is used to calculate the rotordynamic coefficients due to hydrodynamic force of annular clearance in motor air gap.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.6
• /
• pp.452-457
• /
• 2016

Single screw compressors are widely used in the fields of air/gas compression, refrigeration, and chemical fluid transportation systems. A single-screw compressor is composed of a screw rotor and two gate rotors located at both sides. This simple construction enables low rotational speed of the rotor, efficient compression with low noise, low vibration, and long bearing life. Despite these merits, the design method of single-screw compressors is not well known. To accelerate the industrial application of single-screw compressors, a design method using coordinate transformation is presented in this paper, and a tool trajectory is established for machining. Finally, the screw rotor, which is machined using the proposed method, is presented.

• Korean Journal of Animal Reproduction
• /
• v.10 no.1
• /
• pp.42-48
• /
• 1986

These experiments were carried out to develop new techniques identifying XX-bearing embryos prior to implantation by immunological method. Antiserum to histocompatibility-Y(H-Y) antigen was prepared in adult SD(sprague-dawley) female rat by repeated immunization of newbone testis supernatant from males of the same strain. ELISA test was used to identify the H-Y antibody of antiserum. Total 124 mouse embryos (8-cell stage) were treated with H-Y antiserum and complement in BSA free Ho, pp. and Pitt's medium and cultured under the gas phase of 5% CO2 in air at 37$^{\circ}C$ for 24 to 48 hrs. The morphological characteristics of embryos treated were observed under the phase-contrast micro scope. The results obtained in these experiments were summarized as follows: 1. Optimal Density of H-Y antibody were a, pp.ared to be 0.27-0.47 by ELISA test. 2. Of total 124 embryos treated with H-Y antiserum and complement 69(55.6%) embryos developed to blastocyst and 55(44.4%) destroyed or arrested.

• Korean Journal of Animal Reproduction
• /
• v.10 no.1
• /
• pp.36-41
• /
• 1986

These experiments were carried out to obtain basic information necessary for sexing embryos by chromosomal analysis. To observe metaphase chromosomes, all embryos developed to blastocysts were cultured in Ho, pp. & Pitts' medium containing 0.001% Colcemid under the gas phase of 5% CO2 in air at 37$^{\circ}C$ for 2 hours. The sex chromosome of mouse embryos shown normal development after culture in medium containing H-Y antiserum (10%, v/v) and complement (20%, v/v) also was confimed by chromosomal analysis. The results obtained in these experiments were summarized as follows: 1. Among 89 mouse blastocysts, the number of embryos identified to have XX and XY chromosome was 22(25%) and 25(28%), respectively and 42(47%) embryos were not identified. 2. Of total 40 mouse balstocysts cultured in medium containing H-Y antiserum and complement, 23(58%) embryos which were able to be discriminated their sex chromosomes were identified to be XX bearing embryos. 3. Sex chromosomes of a number of embryos subjected to chromosomal analysis were not identified. This result may be due to absence or poor quality of metaphase spreads.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.10-12
• /
• 1998

Pumping liquid metal in nuclear power plant application by conventional centrifugal pumps pose difficulties such as bearing wear out at high temperatures and leak proof sealing of the liquid metal. MHD machine is obtained by replacing solid conducting secondary of conventional motors with ionized gas or liquid metal. It is used for reactor cooling pump because of construction simplicity, perfect sealing and easy operation/maintenance MHD pump is complicated because it includes electromagnetic and hydrodynamic phenomena. The principle of MHD Pumps is described in this paper. We design small laboratory size Flat Linear Induction Pump(FLIP) for transferring sodium.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.1245-1250
• /
• 2006

The rapid growth of the economy recently gas led to increasing social needs for large scaled structures, such as high-rise buildings and long span bridges. In building these large-scaled structures the trend has been to construct foundations beating on or in rock masses in order to ensure stability and serviceability of the structure under several significant loads. However. when designing the drilled shaft foundation socketed in rock masses in Korea, the bearing capacity for the pier used to be determined by using the empirical expression, which depends on the compressive strength of the rock, or presumable bearing capacity recommended on foreign references or manuals. In this study, numerical analyses are used to trace rock-socketed pile behavior and are made alike with pile load test result in field. The result of this numerical analyses study have shown that following factors have a significant influence on the load capacity and settlement of the pier. Significant influence first factor of the geometry of the socket as defined by the length to diameter ratio. Second factor of the modulus of the rock both around the socket and below the base. third factor of the condition of the end of the pier with respect to the removal of drill cuttings and other loose material from the bottom of the socket.

• Economic and Environmental Geology
• /
• v.15 no.1
• /
• pp.17-32
• /
• 1982

The Wolak tungsten-molybdenum deposits are tungsten-molybdenum bearing quartz veins which filled the fractures in Pre-Cambrian pebble-bearing calcareous hornfels, hornfels and Cretaceous granite. There are two vein groups in this mine, Dongsan vein group in the west and Kwangcheon vein group in the east. The ore minerals are wolframite, scheelite, molybdenite, native bismuth, bismuthinite, pyrite, arsenopyrite, chalcopyrite, cubanite, stannite, pyrrhotite, sphalerite, galena, marcasite, Pb-Bi sulfosalt and ilmenite. Quartz, calcite, beryl, fluorite, muscovite, rhodochrosite and siderite are gangue minerals. Fluid inclusion studies were carried out for the quartz, beryl, scheelite, early and late fluorite. Fluid inclusion studies reveal that liquid-gas inclusions are most common and occur in all of the minerals examined. Filling degree of the inclusions in the late fluorite is much higher than that of the inclusions in quartz and early fluorite. Liquid $CO_2$ bearing liquid-gas inclusions occur in quartz and early fluorite. Liquid, gas and solid phase inclusions occur in quartz, beryl and scheelite. Salinities of inclusions in quartz and beryl from Dongsan vein group range from 3.9 to 8.0, from 5.3 to 7.7 wt.% NaCl equivalent respectively. Salinities in the late fluorite range from 1.5 to 3.2 wt.% NaCl equivalent. In Kwangcheon vein group salinities range from 3.9 to 9.6 wt.% NaCl equivalent in quartz, from 2.8 to 7.3 wt.% NaCl equivalent in early fluorite, from 1.3 to 1.5 wt.% NaCl equivalent in late fluorite. Homogenization temperatures of inclusions range from $239^{\circ}$ to higher than $360^{\circ}C$ in quartz, over $360^{\circ}C$ in scheelite, from $288^{\circ}C$ to higher than $360^{\circ}C$ in beryl, and from $159^{\circ}$ to $202^{\circ}C$ in late fluorite of the Dongsan vein group. In Kwangcheon vein group, homo genization temperatures of inclusions range from $240^{\circ}C$ to higher than $360^{\circ}C$ in quartz and from $240^{\circ}$ to $328^{\circ}C$ in early fluorite. As a whole, in Dongsan and Kwangcheon vein groups it seems that there are no distinct differences in mineralogy, salinities and homogenization temperatures. No distinct variations in homogenization temperatures are revealed through about 300 m vertically in both district. The faint trend of increase in salinities in the lower level can be detected. The salinity, $CO_2$ content and the temperature of ore fluid were much higher in the early vein stage and then dropped off in the late stage of mineralization as represented by the quartz and fluorite inclusion data.