• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.03a
• /
• pp.144-147
• /
• 1998

VCR is a back-up roll with a special contour which leads to the length of the contact line between back-up roll and work becones self adjustable in accordance with the width of the strip. The simulation of a finite element model and the on-line test at production mill demonstrate that the VCR roll may keep the crown of the roll gap relatively stable, and at same time, permit the rolling pressure to be adjusted over a wider range, and increase the effect of work roll bending on the roll gap. The VCR rolls have been successfully used at the first stands of two largest cold rolling mills in China, and on-line test has been done at a wide hot strip finishing train. The use of VCR roll has created favorable conditions for subsequent rolling passes and the achievement of better flatness quality.

• Journal of Navigation and Port Research
• /
• v.28 no.1
• /
• pp.31-36
• /
• 2004

In this paper, the characteristics of an inverted-F antenna for the 2.4GHz(ISM) Bluetooth system have been analysed in terms of the variation of design parameters. The antenna can be integrated on printed circuit board, and the characteristics in terms of the variation of the gap between feed line and shorting stub, gap between antenna's leg and ground plane, antenna leg's width, substrate's height and dielectric constant are analysed By using these characterization plot of design parameter, the tuning techniques are proposed to design optimum antenna. The designed antenna has 6.3%(150MHz) frequency bandwidth for VSWR under 1.5, and 3dBi gain.

• Laser Solutions
• /
• v.14 no.3
• /
• pp.17-20
• /
• 2011

We fabricated a multi-layer diffraction grating inside fused silica glass by using a femtosecond laser direct writing method. The femtosecond laser with a wavelength of 515 nm, a pulse width of 250 fs, a repetition rate of 100 kHz, and an average output power of 6 W was used. Two layer diffraction grating with a grating period of $6{\mu}m$ was successfully fabricated with the layer gap of 0.5, 1, 2, 3, and $5{\mu}m$, respectively. Also, we investigated the diffraction pattern by illuminating a He-Ne laser beam. Finally, we demonstrated the diffraction grating with a grating period of $3{\mu}m$ by adjusting the gap of each layer with a grating period of $6{\mu}m$. Femtosecond laser direct writing technology of multi-layer has a potential to fabricate the diffraction grating with a grating period of below $1.5{\mu}m$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.4
• /
• pp.57-64
• /
• 2000

In this paper, to achieve the constant thrust force of the double side moving-magnet type LDM, the new armature winding of the LDM was proposed so as to restrain the saturation of the center yoke without increasing the mass of LDM. According to analyzing the magnetic flux distribution throughout the air-gap of the LDM, the magnet and winding width (1:0.84) was determined. The 2D finite element analysis was performed for force analysis on air-gap.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.9
• /
• pp.2505-2513
• /
• 1996

This paper presents the analysis of the impedance characteristic of the strip type waveguide mount backed by the dielectric substrate using mode the matching and induced EMF method. The part of the waveguide containing the dielectric substrate is modeled as waveguide partially filled with the dielectric, and a hybrid mode analysis has been conducted for the structure. The electromagnetic scattering problem by the dielectric substrate is solved by the mode matching method using the calculated modal function. The input impedance seen at the mount gap is calculated by the induced EMF method using the calculated results. the calculated results thus obtained has been verified through comparison with the results by other numerical methods. The effect of some structure parameters such as the width of the substrate and the gap size on the mount impedance is investigated.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.6
• /
• pp.185-188
• /
• 2009

The effects of the growth temperature on the properties of ZnO thin films were investigated by using X-ray diffraction, scanning electron microscopy, ultraviolet-visible spectrophotometry, and Hall measurements. The ZnO films were deposited by rf magnetron sputtering at various growth temperatures in the range of 100-$400{^{\circ}C}$. A strong c-axis preferred orientation is observed for all of the samples. As the growth temperature increases, the crystalline orientation of the ZnO (002) plane is not changed, but the full width at half maximum gets smaller. The dependence of the electron concentration, mobility, and resistivity on the growth temperature exhibits that the ZnO films have a higher electron concentration at higher temperatures, thus giving them a low resistivity. The optical transmittance and band gap energy, calculated from the spectra of optical absorbance, show a significant dependence on the growth temperature. As for the sample grown at $100{^{\circ}C}$, the average transmittance is about 90% in the visible wavelength range and the band gap is estimated to be 3.13 eV.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.12
• /
• pp.592-600
• /
• 2005

In this paper, a low loss magnetic levitation(Maglev) system is suggested and tested. The suggested Maglev system includes four hybrid magnets which consist of permanent magnet and coil. In the steady state, the levitated module system can be supported by attraction force generated by permanent magnet. The coil current controls only dynamic loads due to external disturbances. The module systems are designed by using finite element method(FEM) software tools such as MAXWELL and ANSYS. Also, digital control systems are designed to keep the magnet airgap at a constant value. The control systems include a VME(versa module europa)-based CPU(central processing unit) board, AD(analog to digital) board, PWM(pulse width modulation) board, 4-quadrant chopper, and sensors. In order to estimate the vertical velocity of the magnet, we use second order state observer with acceleration and gap signals as input and output signals, respectively. The characteristics of the suggested low loss Maglev system are demonstrated by experimental results showing coil current of 0A in the steady state of 3m airgap and performance specifications are satisfied for reference gap and force disturbance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.116-119
• /
• 2003

[ $Hg_{1-x}Cd_xTe$ ] (MCT) was grown by hot wall epitaxy method. Prior to the MCT growth, the CdTe (111) buffer layer was grown on the GaAs substrate at the temperature of 590 C for 15 min. When the thickness of the CdTe buffer layer was 5 m or thicker, the full width at half maximum values obtained from the x-ray rocking curves were found to significantly decrease. After a good quality CdTe buffer layer was grown, the MCT epilayers were grown on the CdTe (111) /GaAs substrate at various temperature in situ. The crystal quality for those epilayers was investigated by means of the x-ray rocking curves and the photocurrent experiment. The photoconductor characterization for the epilayers was also measured. The energy band gap of MCT was determined from the photocurrent measurement and the x composition rates from the temperature dependence of the energy band gap were turned out.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.5
• /
• pp.110-117
• /
• 2002

This paper proposes a optimization of the design variables of linear motor for the improvement of thrust. Especially, this paper treats the shoe, which can be good to flow of a magnetic flux in linear motor. Firstly, this paper uses a space harmonic analysis method(SHAM) based on Fourier series, for analyzing the characteristics of core type linear motor, including slot structure and shoe. And compare the magnetic flux densities of linear motor at air gap with the results of the SHAM and the Finite Element Method(FEM). Secondly, this paper uses a genetic algorithm, which is good to find the global solutions. The design variables are the pole pitch of magnet, the pitch of slot, the height of slot, the width of shoe and the width of magnet. The maximum thrust with optimum design variables is about 247 N which is improved about 16%.

• The Journal of the Acoustical Society of Korea
• /
• v.13 no.6
• /
• pp.45-49
• /
• 1994

In this paper, photoacoustic image processing system was constructed by using 2W CW $CO_{2}$ laser of $10.6{\mu}m$ wavelength and PZT 5A acoustic transducer. Stainless steel of 5mm thickness was used as a sample in experiment. Three line cracks of $50{\mu}m$ in each width and depth were made by using plasma on the surface of the sample. Also, each gap among their lines was $200{\mu}m$ and $300{\mu}m$ in width. In the scan range of $2.2mm\times2mm$ including surface defects, a good image of $50{\mu}m$ resolution had been shown when modulation frequency of CW laser was 100Hz.