• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.138-138
• /
• 2009

Recently, thin-film solar cells of Cu(In,Ga)$Se_2$(CIGS) have reached a high level of performance, which has resulted in a 19.9%-efficient device. These conventional devices were typically fabricated using chemical bath deposited CdS buffer layer between the CIGS absorber layer and ZnO window layer. However, the short wavelength response of CIGS solar cell is limited by narrow CdS band gap of about 2.42 eV. Taking into consideration the environmental aspect, the toxic Cd element should be replaced by a different material. It is why during last decades many efforts have been provided to achieve high efficiency Cd-free CIGS solar cells. In order to alternate CdS buffer layer, ZnS buffer layer is grown by using chemical bath deposition(CBD) technique. The thickness and chemical composition of ZnS buffer layer can be conveniently by varying the CBD processing parameters. The processing parameters were optimized to match band gap of ZnS films to the solar spectrum and exclude the creation of morphology defects. Optimized ZnS buffer layer showed higher optical transmittance than conventional thick-CdS buffer layer at the short wavelength below ~520 nm. Then, chemically deposited ZnS buffer layer was applied to CIGS solar cell as a alternative for the standard CdS/CIGS device configuration. This CIGS solar cells were characterized by current-voltage and quantum efficiency measurement.

• Journal of Information Display
• /
• 제9권4호
• /
• pp.21-29
• /
• 2008

We studied both the wavelength and intensity dependent photo-responses (photofield-effect) in amorphous In-Ga-Zn-O (a-IGZO) thin-film transistors (TFTs). During the a-IGZO TFT illumination with the wavelength range from $460\sim660$ nm (visible range), the off-state drain current $(I_{DS_off})$ only slightly increased while a large increase was observed for the wavelength below 400 nm. The observed results are consistent with the optical gap of $\sim$3.05eV extracted from the absorption measurement. The a-IGZO TFT properties under monochromatic illumination ($\lambda$=420nm) with different intensity was also investigated and $I_{DS_off}$ was found to increase with the light intensity. Throughout the study, the field-effect mobility $(\mu_{eff})$ is almost unchanged. But due to photo-generated charge trapping, a negative threshold voltage $(V_{th})$ shift is observed. The mathematical analysis of the photofield-effect suggests that a highly efficient UV photocurrent conversion process in TFT off-region takes place. Finally, a-IGZO mid-gap density-of-states (DOS) was extracted and is more than an order of magnitude lower than reported value for hydrogenated amorphous silicon (a-Si:H), which can explain a good switching properties observed for a-IGZO TFTs.

• Asian Pacific Journal of Cancer Prevention
• /
• 제16권18호
• /
• pp.8271-8279
• /
• 2016

Background: Hepato-carcinogenesis is multifaceted in its molecular aspects. Among the interplaying agents are altered gap junctions, the proteasome/autophagy system, and mitochondria. The present experimental study was designed to outline the roles of these players and to investigate the tumor suppressive effects of curcumin with or without mesenchymal stem cells (MSCs) in hepatocellular carcinoma (HCC). Materials and Methods: Adult female albino rats were divided into normal controls and animals with HCC induced by diethyl-nitrosamine (DENA) and $CCl_4$. Additional groups treated after HCC induction were: Cur/HCC which received curcumin; MSCs/HCC which received MSCs; and Cur+MSCs/HCC which received both curcumin and MSCs. For all groups there were histopathological examination and assessment of gene expression of connexin43 (Cx43), ubiquitin ligase-E3 (UCP-3), the autophagy marker LC3 and coenzyme-Q10 (Mito.Q10) mRNA by real time, reverse transcription-polymerase chain reaction, along with measurement of LC3II/LC3I ratio for estimation of autophagosome formation in the rat liver tissue. In addition, the serum levels of ALT, AST and alpha fetoprotein (AFP), together with the proinflammatory cytokines $TNF{\alpha}$ and IL-6, were determined in all groups. Results: Histopathological examination of liver tissue from animals which received DENA-$CCl_4$ only revealed the presence of anaplastic carcinoma cells and macro-regenerative nodules. Administration of curcumin, MSCs; each alone or combined into rats after induction of HCC improved the histopathological picture. This was accompanied by significant reduction in ${\alpha}$-fetoprotein together with proinflammatory cytokines and significant decrease of various liver enzymes, in addition to upregulation of Cx43, UCP-3, LC3 and Mito.Q10 mRNA. Conclusions: Improvement of Cx43 expression, nonapoptotic cell death and mitochondrial function can repress tumor growth in HCC. Administration of curcumin and/or MSCs have tumor suppressive effects as they can target these mechanisms. However, further research is still needed to verify their effectiveness.

• Korea-Australia Rheology Journal
• /
• 제16권2호
• /
• pp.63-73
• /
• 2004

Flow in a channel with an obstruction at the entry can be reverse, stagnant or forward depending on the position of the obstruction. These flow phenomena have potential applications in the control of energy and various flows in process engineering. Parameters that affect this flow inside and around the test channel are the gap (g) between the obstruction geometry and the test channel, the Reynolds number (Re) and the length (L) of the test channel. The influence of these parameters on the flow behavior was investigated using a flat plate obstruction at the entry of the channel. A low concentration polyacrylamide solution (0.018% by weight) showing a powerlaw fluid behavior was used as the fluid in this investigation. The flow phenomena were investigated by the velocity measurement and the flow visualization and their results were compared with numerical simulation. These results of low concentration polyacrylamide solution are also compared with the results of water published elsewhere (Kabir et al., 2003). The maximum reverse flow inside the test channel observed was 20% - 30% of the outside test channel velocity at a g/w (gap to width) ratio of 1 for Reynolds numbers of 1000 to 3500. The influence of the test channel length (L) and the Reynolds number (Re) on the velocity ratio ($V_i$/$V_o$: inside velocity/outside velocity in the test channel) are also presented and discussed here.

• 한국진공학회지
• /
• 제6권3호
• /
• pp.249-254
• /
• 1997

Fe가 첨가된 반절연성 InP(100)의 특성을 photoreflectance(R) 측정으로 조사하였다. 관측한 PR 신호로부터 300K에서 띠간격 에너지($E_o$)와 넓어지기 변수(broadening parameter:$\Gamma$)는 각각 1.336eV 및 11.2meV의 값을 얻었다. 측정온도를 300~80K로 낮춤에 따라 PR 신호는 엑시톤과 2차원의 띠사이 전이가 중첩된 형태(300K)에서 전형적인 엑시톤 에 의한 전이형태(80K)로 변함을 알았다. 또한 Varshni 계수 $\alpha=-0.94\pm$0.07meV/K, $\beta=587\pm$35.2K와 Bose-Einstein 계수 aB=33.6$\pm$2.02meV, $\theta=165\pm$33K의 값을 얻었다. 그리고 등온 및 등시 열처리를 수행한 후 측정 결과, 온도 $300^{\circ}C$에서 10~20분 정도 열처리시켰을 때 InP 시료의 결정성이 가장 좋아짐을 정성적으로 알 수 있었다.

• 한국주조공학회지
• /
• 제12권3호
• /
• pp.210-219
• /
• 1992

The measurement of the apparent and tap density for Al-Pb-X(Sn,Sn-Si) powders produced by centrifugal atomizer showed that the larger theoretically calculated densities the larger those densities. And tap densities were not over 50% of the theoretical densities. The nip angle of Al-5wt%Pb alloy powders produced with 38000 r.p.m. of disk rotation was $3^{\circ}$ degree larger than that of Al-8.5wt%Pb-3wt%Sn(-4wt%Si, 8wt%Si) with 50000 r.p.m. The effects of roll gap and rolling speed on thickness and density of the single strips by rolling were that rolling speed increasing the thickness and density of strip decreased and roll gap increasing, the thickness of strip increased but the density decresed. The compactibility of Al-Pb-X with Al by rerolling showed that the coarse powder-strips were better than fine powder-strips. From the SEM study with EDX analysis on the sintered strips, it was found that Pb and Sn were segregated with maximum size $5{\mu}m$, and Si existed surrounding the segregation zone. After sintering the clad strips at $500^{\circ}C$, the pores, which were spherical with $5{\mu}m$ of mean diameter, partly remained around the particles of alloy powders area, while completely disappeared at clad interface. The hardness of strips of alloy powders decreased linearly with increasing sintering temperature.

• 복식문화연구
• /
• 제16권6호
• /
• pp.1035-1049
• /
• 2008

The purpose of this study was specifically focused on the lower garment sizing system of adolescent apparel, especially on trousers for adolescent boys. Research Method was performed by using the physical measurements of adolescent boys ($14\sim19$ years old, n=1,344) based on the 'he fifth Korean national physical standard reports' surveyed by SIZEKOREA. The basic materials for this study are obtained from the observations of physical characteristics and classification of physical figures based on the characteristics from waist down. The results from this study are as follows. 1) according to the analyses of physical changes, most items including height, circumference, length, breadth and depth were increased at the age of $14\sim18$ and gradually reduced at the age of 19. 2) The factors which compose the lower body resulted were appeared that the first factor was vertical factor, the second factor was horizontal factor, the third factor was hip length, and the last factor was buttlock-popliteal length. 3) Formalization of physical figures for adolescent boy's lower body analyzed from factors grouped three types. 4) The basic parts that we used to propose the apparel sizing system distinguished by physical figures were Waist Circumference (Omphalion) (every 3cm regular gap) and Hip Circumference (irregular gap). Physical figures assigned 5 to Type T, and 4 to type M. The reference measurement items were divided into 7 items which are correlated with apparel manufacture.

• 동의생리병리학회지
• /
• 제19권6호
• /
• pp.1666-1672
• /
• 2005

Oriental medicinal drugs have a broad spectrum of clinical use for the cure of nervous system diseases including brain ischemic damages or neuropathies. Yet, specific drugs or drug components used in the oriental medicine in relation to none fiber regeneration are not known. In the present study, possible growth promoting effects of oriental medicinal drugs were investigated in the injured sciatic nerve system in the rat. By immunofluorescence staining, we found that Jahageo (JHG, Hominis placenta) increased Induction levels of axonal growth associated protein GAP-43 in the rat sciatic none. Small growth promoting activity was found in Golsebo (GSB, Drynariae rhizoma) and Baikhasuo (BHSO, Polygoni multiflori radix) drugs. JHG also increased cell cycle protein Cdc2 levels in the injured area of the sciatic nerves. Immunofluorescence staining indicated that induced Cdc2 protein was mostly localized in the Schwann cells in the injury area, implying that JHG activity might be related to increased Schwann cell proliferation during axonal regeneration. Moreover, levels of phospho-extracellular signal-regulated (ERK) pathway in the injured neNes were elevated by JHG treatment while levels of total ERK were unaltered. In vivo measurement of axonal regeneration using retrograde tracer showed that JHG, GSB and BHSO significantly enhanced Dil-labeled regenerating motor neurons compared with saline control. The present data suggest that oriental medicinal drugs such as JHG, GSB, and BHSO may be a useful target for developing specific drugs of axonal regeneration.

• Nuclear Engineering and Technology
• /
• 제45권5호
• /
• pp.613-624
• /
• 2013

Multi-dimensional two-phase phenomena occur in many industrial applications, particularly in a nuclear reactor during steady operation or a transient period. Appropriate modeling of complicated behavior induced by a multi-dimensional flow is important for the reactor safety analysis results. SPACE, a safety analysis code for thermal hydraulic systems which is currently being developed, was designed to have the capacity of multi-dimensional two-phase thermo-dynamic phenomena induced in the various phases of a nuclear system. To validate the performance of SPACE, a two-dimensional two-phase flow test was performed with slab geometry of the test section having a scale of $1.43m{\times}1.43m{\times}0.11m$. The test section has three inlet and three outlet nozzles on the bottom and top gap walls, respectively, and two outlet nozzles installed directly on the surface of the slab. Various kinds of two-dimensional air/water flows were simulated by selecting combinations of the inlet and outlet nozzles. In this study, two-dimensional two-phase void fraction profiles were quantified by measuring the local gap impedance at 225 points. The flow conditions cover various flow regimes by controlling the flow rate at the inlet boundary. For each selected inlet and outlet nozzle combination, the water flow rate ranged from 2 to 20 kg/s, and the air flow rate ranged from 2.0 to 20 g/s, which corresponds to 0.4 to 4 m/s and 0.2 to 2.3 m/s of the superficial liquid and gas velocities based on the inlet port area, respectively.

• 디지털융복합연구
• /
• 제10권4호
• /
• pp.1-9
• /
• 2012

새로운 IT제품인 3차원 텔레비전(3DTV)은 우리생활에서 TV가 방송을 시청하는 도구 이상으로 다양한 분야에 활용될 수 있다는 가능성을 제시하고 있다. 3DTV는 2차원 TV보다 우수한 효능을 갖지만 내제된 문제점을 개선하기 위해 지속적인 기술개발을 요구하고 있다. 이러한 혁신기술들은 품질이 수용과 사용에 중요한 영향을 미치기 때문에 효과적인 품질측정 방법으로 품질개선을 요구한다. 본 연구에서는 계층적분석과정을 사용한 3DTV의 품질 측정 방법을 제안하였다. 문헌적 고찰을 통하여 3DTV의 품질기준들을 도출하고, 품질측정 방법으로 품질 갭을 계산하는 대신 상대적 품질척도인 품질비율 개념을 제안하였다. 네 가지 유형의 품질개념을 제안하였고, 수치적인 예제를 통하여 3DTV의 품질점수 도출과 3DTV간 품질 우선순위를 계산하는 절차를 보였다.