• Journal of Electrical Engineering and Technology
• /
• v.1 no.3
• /
• pp.327-331
• /
• 2006

This paper presents the analysis method for the torque characteristic of the 1-phase induction motor considering space harmonics in the air gap. The equivalent circuit method is used, where the circuit constants are obtained by classic theory. In addition, the space harmonic components in air gap magneto motive force are analyzed and added to the equivalent circuit to obtain accurate torque characteristics in low speed regions. Each torque component due to the harmonics is calculated and the total torque characteristic is obtained and compared with the measurement result.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.8
• /
• pp.957-968
• /
• 1999

Performance tests of an airfoil fan and measurement of flow fields at the impeller exit are carried out to investigate the effects of the tip clearance between the rotor and inlet casing on the impeller performance. The impeller is twelve bladed of NACA 65-810 airfoils and tested with 3 different size of gap; 1, 2, 4mm. The relative decrease of pressure rising performance of the fan is 15 percent for the design flow rate when the gap size is 1 percent of the impeller diameter. The reduction of performance becomes large as the flow rate increases. The leakage flow through the clearance affects the through flow of the impeller, which results in decrease of the slip factor as well as the impeller efficiency. The data base obtained in the present study can be used for the design and flow analysis of the airfoil fans.

• Journal of Sensor Science and Technology
• /
• v.13 no.4
• /
• pp.277-281
• /
• 2004

$Hg_{1-x}Cd_{x}Te$ (MCT) was grown by hot wall epitaxy. Prior to the MCT growth, the CdTe (111) buffer layer was grown on the GaAs substrate at the temperature of $590^{\circ}C$ for 15 min. When the thickness of the CdTe buffer layer was $5{\mu}m$ or thicker, the full width at half maximum values obtained from the x-ray rocking curves were found to significantly decrease. After a good quality CdTe buffer layer was grown, the MCT epilayers were grown on the CdTe (111)/GaAs substrate at various temperatures in situ. The crystal quality for those epilayers was investigated by means of the x-ray rocking curves and the photocurrent experiment. The photoconductor characterization for the epilayers was also measured. The energy band gap of MCT was determined from the photocurrent measurement and the x composition rates from the temperature dependence of the energy band gap were turned out.

• Journal of Power System Engineering
• /
• v.3 no.4
• /
• pp.79-85
• /
• 1999

The magnetic levitation system is utilized in the magnetic bearing of high-speed rotor system because of little friction, no lubrication, no noise and so on. The magnetic levitation system needs the feedback controller for the stabilization of system, and gap sensors are generally used to measure the gap. The use of sensor easily goes into troublesome caused by sensor failure discord between the measurement point and the control point etc. This paper gives a controller design method of magnetic levitation system which satisfies the given $H_{\infty}$ control performance and the robust stability of the presence of physical parameter perturbations. To the end, we investigated the validity of the designed controller through results of simulation.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.152-152
• /
• 2003

Hg$\sub$l-x/Cd$\sub$x/Te (MCT) was grown by hot wall epitaxy. Prior to the MCT growth, the CdTe (111) buffer layer was grown on the GaAs substrate at the temperature of 590$^{\circ}C$ for 15 min. When the thickness of the CdTe buffer layer was 5 $\mu\textrm{m}$ or thicker, the full width at half maximum values obtained from the x-ray rocking curves were found to significantly decrease. After a good quality CdTe buffer layer was grown, the MCT epilayers were grown on the CdTe (111) /GaAs substrate at various temperatures in situ. The crystal quality for those epilayers was investigated by means of the x-ray rocking curves and the photocurrent experiment The photoconductor characterization for the epilayers was also measured The energy band gap of MCT was determined from the photocurrent measurement and the x composition rates from the temperature dependence of the energy band gap were turned out

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1814-1818
• /
• 1989

The crystals of ZnGa2S4 and ZnGa2S4:Co(2mole%) were synthesized from high-purity (99.999%) elements of Zinc, Gallium, and sulfur. The crystal structure of these crystals belong to a tetragonal system with layer type and the lattice constants are a =5.35\ulcorner c=10.43\ulcornerfor ZnGa2S4: Co(2 mole%) crystal at 298\ulcorner. The optical absorption spectra of these compounds were obtained through reflectance measurements using a 60 mm diameter intergrating sphere. The optical energy gaps are 3.18eV for ZnGa2S4 and 2.60eVfor ZnGa2S4:L Co(2mole%)at 298\ulcorner, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.379-379
• /
• 2010

$Hg_{1_x}Cd_xTe$ (MCT) was grown by hot wall epitaxy. Prior to the MCT growth, the CdTe (111) buffer layer was grown on the GaAs substrate at the temperature of $590^{\circ}C$ for 15 min. When the thickness of the CdTe buffer layer was $5\;{\mu}m$ or thicker, the full width at half maximum values obtained from the x-ray rocking curves were found to significantly decrease. After a good quality CdTe buffer layer was grown, the MCT epilayers were grown on the CdTe (111) /GaAs substrate at various temperatures in situ. The crystal quality for those epilayers was investigated by means of the x-ray rocking curves and the photocurrent experiment. The photoconductor characterization for the epilayers was also measured. The energy band gap of MCT was determined from the photocurrent measurement and the x composition rates from the temperature dependence of the energy band gap were turned out.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.33 no.4
• /
• pp.297-306
• /
• 2007

Distraction osteogenesis was pioneered by Ilizarov in the treatment of injured extremities. Its subsequent application to Oral and Maxillofacial Surgery has opened a new chapter in the treatment of facial deformity. Careful monitoring of the period of distraction and consolidation of the callus is important and has been well described. Complications, such as infection, haematoma and premature ossification, are difficult to diagnose and can compromise the outcome after the surgery. Too slow rate of distraction results in premature fusion of cortices and too rapid information of bone 'cyst' within the callus distraction. I experienced 2 patients of congenital unilateral mandibular hypoplasia, so called Hemifacial Microsomia. After distraction surgery, I evaluated callus formation of mandibular distraction with Ultrasound Sonography during distraction and consolidation period. Plain radiography, although it enables accurate measurement of the distraction gap, did not give sufficient detail to allow assessment of early stages of bone formation, But, ultrasound monitoring could enable continuous monitoring of the distraction gap without exposure to ionizing radiation and allow detection of fine detail, which may influence manipulation of the callus.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.453-457
• /
• 2001

One of the major limitations of productivity and quality in metal cutting is the machining accuracy of machine tools. The machining accuracy is affected by geometric and thermal errors of the machine tools. In this study, the compensation device is manufactured in order to compensate thermal error of machine tools under the real-time. This paper models of the thermal errors for error analysis and develops on-the-machine measurement system by which the volumetric error are measured and compensated. The thermal error is modeled by means of angularity errors of a column and thermal drift error of the spindle unit which are measured by the touch probe unit with a star type styluses, a designed spherical ball artifact, and five gap sensors. In order to compensate thermal characteristics under several operating conditions, experiments performed with five gap sensors and manufactured compensation device on the horizontal machining center.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.943-946
• /
• 1997

Electropolishing is the controlled electrochemical removal of surface metal, resultmg in a brilliant appearance andimproved properties. Sometimes described as "reverse plating," the process has a leveling effect, which produces smoothnessand increased reflectivity. Unlike conventional mechanical finishing systems, the electropolishing does not smear, bend,stress or fracture the crystalline metal surface to achieve smoothness. Instead, electropolishing removes metal from thesurface producing a unidirectional pattern that is stress-free, microscopically smooth and often highly reflective. In addition,improved corrosion resistance and passivity are achieved on many ferrous and some non-ferrous alloys. Pure aluminium doesnot electropolish well, if at all, but most other alloys of aluminum electropolish excellently.Therefore, the aim of this study is to determine the characteristics of electropolishing aluminium alloy in term of currentdensity, machining time, temperature, electrode gap and workpiece surface measurementkpiece surface measurement