• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.868-882
• /
• 2009

In this paper, channel model and wireless link performance analysis for the short-range wireless communication system applications in the terahertz frequency which is currently interested in many countries will be described. In order to realize high data rates above 10 Gbps, the more wide bandwidths will be required than the currently available bandwidths of millimeter-wave frequencies, therefore, the carrier frequencies will be pushed to THz range to obtain larger bandwidths. From the THz atmospheric propagation characteristics based on ITU-R P.676-7, the available bandwidths were calculated to be 68, 48 and 45 GHz at the center frequencies of 220, 300 and 350 GHz, respectively. With these larger bandwidths, it was shown from the simulation that higher data rate above 10 Gbps can be achieved using lower order modulation schemes which have spectral efficiency of below 1. The indoor propagation delay spread characteristics were analyzed using a simplified PDP model with respect to building materials. The RMS delay spread was calculated to be 9.23 ns in a room size of $6\;m(L){\times}5\;m(W){\times}2.5\;m(H)$ for the concrete plaster with TE polarization, which is a similar result of below 10 ns from the Ray-Tracing simulation in the reference paper. The indoor wireless link performance analysis results showed that receiver sensitivity was $-56{\sim}-46\;dBm$ over bandwidth of $5{\sim}50\;GHz$ and antenna gain was calculated to be $26.6{\sim}31.6\;dBi$ at link distance of 10m under the BPSK modulation scheme. The maximum achievable data rates were estimated to be 30, 16 and 12 Gbps at the carrier frequencies of 220, 300 and 350 GHz, respectively, under the A WGN and LOS conditions, where it was assumed that the output power of the transmitter is -15 dBm and link distance of 1 m with BER of $10^{-12}$. If the output power of transmitter is increased, the more higher data rate can be achieved than the above results.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.48-57
• /
• 2006

This work describes a 12b 200KHz 0.52mA $0.47mm^2$ algorithmic ADC for sensor applications such as motor controls, 3-phase power controls, and CMOS image sensors simultaneously requiring ultra-low power and small size. The proposed ADC is based on the conventional algorithmic architecture with recycling techniques to optimize sampling rate, resolution, chip area, and power consumption. The input SHA with eight input channels for high integration employs a folded-cascode architecture to achieve a required DC gain and a sufficient phase margin. A signal insensitive 3-D fully symmetrical layout with critical signal lines shielded reduces the capacitor and device mismatch of the MDAC. The improved switched bias power-reduction techniques reduce the power consumption of analog amplifiers. Current and voltage references are integrated on the chip with optional off-chip voltage references for low glitch noise. The employed down-sampling clock signal selects the sampling rate of 200KS/s or 10KS/s with a reduced power depending on applications. The prototype ADC in a 0.18um n-well 1P6M CMOS technology demonstrates the measured DNL and INL within 0.76LSB and 2.47LSB. The ADC shows a maximum SNDR and SFDR of 55dB and 70dB at all sampling frequencies up to 200KS/s, respectively. The active die area is $0.47mm^2$ and the chip consumes 0.94mW at 200KS/s and 0.63mW at 10KS/s at a 1.8V supply.

• Journal of Korean Society of Forest Science
• /
• v.83 no.2
• /
• pp.191-204
• /
• 1994

Due to its topographic complexities and various climatical condition, Korea exhibits diverse forest types. Dominant tree species in this zone are Quercus spp., Betula spp., Zelkova spp., Fraxinus spp., Pinus densiflora, Pinus koraiensis, and Pinus thunbergii ete. Genetic conservation in forest species in Korea there are three ways ; one is in situ, other is ex situ and third is in-facility conservation. In situ conservation include that are the present status of conservation of rare and endangered flora and ecosystem, the reserved forest, the national and provincial park, and the gene pool of natural forests. Ex situ conservation means to be established the new forest from in situ forest stands, progeny and provenance test populations, seed orchard and clone banks, and gene conservation in-facility. As a tool for low temperature storage, several aspects on in vitro system were studied ; (1) establishment of in vitro cultures from juvenile and/or rejuvenated tissues, (2) induction of multiple shoots from the individual micropropagules, (3) elongation of the proliferated shoots. Studies on cold storage for short-and long-term maintenance of in vitro cultures under $4^{\circ}C$ in the refrigerator were conducted. For the cryopreservation at $-196^{\circ}C$, various factors affecting survivability of the plant materials are being examined. The necessity of gene conservation of forest trees is enlarged not only to increase the adaptability for various environments but also to gain the breeding materials in the future. For effective gene conservation of forest trees, I would like to suggest followings ; 1. Forest stands reserved for other than the gene conservation purposes such as national parks should be investigated by botanical and gene-ecological studies for selecting bio-diversity and gene conservation stands. 2. Reserved forest for gene pool should be extented both economically important tree spp. and non-economical species. 3. Reserved forest for progeny test and clone bank should be systematically investigated for the use of Ex situ forest gene conservation. 4. We have to find out a new methodology of genetic analysis determining the proper and effective size of subpopulation for in situ gene conservation. 5. We should develop a new tree breeding systems for successful gene conservation and utilization of the genetic resources. 6. New method of in-facility gene conservation using advanced genetic engineering should be developed to save time and economic resources. 7. For the conservation of species with short-life span of seed or shortage of knowledge of seed physiology, tissue culture techniques will be played a great role for gene conservation of those species. 8. It is are very useful conservation not only of genes but of genotypes which were selected already by breeding program. 9. Institutional and administrative arrangements including legistlation must be necessarily taken for gene conservation of forest trees. 10. It is national problems for conservation of forest resources which have been rapidly destroyed because of degenerating environmental condition and of inexperienced management system of bio-diversity and gene conservation. 11. In order to international cooperation for exchanging data of bio-diversity and gene conservation, we should connect to international net works as soon as possible.

• Journal of Animal Science and Technology
• /
• v.44 no.6
• /
• pp.643-652
• /
• 2002

Data were consisted of the ten body measurements (withers height, rump height, body length, chest depth, chest width, rump width, rump length, thurls width, hipbone width and chest girth) of 642 steers (Korean cattle), which was entered in the National Beef Quality Contest hosted by the Korea Animal Improvement Association from 1997 to 2001. A principal components analysis was used to classify the body types of the steers, and estimate the correlations between carcass traits and principal components for the body measurements of the first, second, third and fourth period, respectively. The first principal component of body measurements at the first, second, third and fourth period accounted for 76.0%, 83.0%, 72.7% and 57.4% of the total variance, respectively. The sum of first, second and third principal component at each period accounted for 86.69%, 90.49%, 84.62% and 77.26% of the total variance, respectively. At each period, all the first principal component of the body measurements were positive and it generally showed large framed body shape. The size of body was influenced mostly by chest depth(0.328${\sim}$0.339) and rump length(0.325${\sim}$0.341). The second, third and fourth principal component at the each period were various. There were positive correlations between principal components index of each period and carcass traits such as carcass weight(0.539${\sim}$0.755), average daily gain(0.256${\sim}$0.564), backfat thickness(0.227${\sim}$0.280), and eye muscle area(0.187${\sim}$0.344). The correlation with yield grade index(－0.246${\sim}$－0.110), however, was negative. The correlation with marbling score(0.066${\sim}$0.099) was low or statistically insignificant. According to principal component indexes of the second, third, and fourth components, the correlations with the carcass traits were various. There were no large differences between the correlations of the single body measurement trait with the carcass traits and the correlations of the first principal component indexes with the carcass traits.

• Journal of Veterinary Clinics
• /
• v.31 no.5
• /
• pp.394-402
• /
• 2014

The objective of this study was to investigate the effect of chronic unpredictable stress on the reproductive function and ovarian luteinizing hormone receptor (LHR) expression. 9-week-old C57BL/6 female mice were randomly divided into two groups: control group and stressed group. Mice have been stressed twice a day for 35 days with 12 different stressors which were randomly selected. The results demonstrate that there is significant increase in the anxiety-related behaviors (P < 0.05), decrease body weight gain rate (P < 0.01) and decrease in the average of litter size in stressed mice compared with control group (P < 0.01). Furthermore, the rate of primary, secondary and early antral follicles in stressed mice significantly decreased (P < 0.05), whereas that of atretic follicles significantly increased compared with control mice (P < 0.01). The immunohistochemical analysis revealed that reduced LHR expression in granulosa cells of follicle and luteal cells of corpus luteum in response to chronic unpredictable stress. The western blot analysis revealed significantly decrease in LHR expression in the stressed mice ovaries compared with the control (P < 0.05). These results suggest that ovarian LHR expression affected by chronic unpredictable stress and the modulated ovarian LHR is responsible for ovarian follicular maldevelopment and reproductive dysfunction.

• Journal of Animal Science and Technology
• /
• v.50 no.2
• /
• pp.185-198
• /
• 2008

Influences of dietary brown seaweed(BSW) on the nutrient metabolism, anti-oxidant enzyme activity and cell-mediated immune response were studied in broiler chicks activated acute phase response. 72 Hatched male broiler chicks(Ross) were divided into 12 pens, 6 heads per pen, and fed the BSW 0.0% (Basal) or 2.0% diet, respectively, and injected with the Salmonella typhimurium lipopoly saccharide(LPS) for activation of the acute phase response three times at 8, 10 and 12 d of age. During 4 wks of experimental feeding, growth performance of broiler chicks was not affected by dietary BSW and the acute phase response. Compared with control birds, the acute phase response did not affect the daily weight gain in birds fed BSW 2.0% diet, decreased nitrogen balance(NB) or metabolizable energy(ME) utilization per metabolic body size(kg0.75), and enhanced activities of peroxidase or extracellular SOD(EcSOD), tumor necrosis factor-alpha and ovotransferrin in plasma and MnSOD and CuZnSOD in erythrocyte cytosol. Compared to BSW 0.0% diet, 2.0% diet enhanced protein retention(NB) per kg0.75 regardless the acute phase response, did not affect uric acid nitrogen excretion(UAN) per kg0.75 in birds during the acute phase response, decreased(p<0.05) the UAN excretion per kg0.75 in control birds. And BSW 2.0% diet also decreased(p<0.05) plasma peroxide level and erythrocyte peroxidase or MnSOD activity but increased plasma peroxidase and EcSOD activity and interleukin-1 activity secreted from LPS-stimulated PBMC in 4 week broiler chicks.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.5
• /
• pp.361-367
• /
• 1984

In previous paper(Lee et al., 1984), preparation formula and processing conditions of the fish meat (mackerel) paste using dielectric heating were described, that included the proper shape and size of product and the conditions of dielectric heating, hot air dehydration, and heating with electric heater to yield the minimum expansion and case hardening during heating and to controll the final rater activity of 0.86 to 0.83 accompanying with a complete reduction of viable cells and good texture. In present study, changes in VBN, pH, total plate count, water activity, texture, the loss of available lysine, color indexes, TBA value, and the content of TI were determined to assess the quality stability and shelf-life of the product during the storage for 35 days at $5^{\circ}C\;and\;25^{\circ}C$, respectively. And the effect of vacuum sealing and hot water treatment before storage on the storage stability of product was also mentioned. As the product was vacuum packed in K-flex film bag, heat treated in boiling water for 6 minutes, and stored, water activity was maintained 0.86 to 0.84 for 35 days regardless of storage temperature, and the increase of total plate count was negligible in case of $5^{\circ}C$ storage while tended to gain slightly after 25 days at $25^{\circ}C$ storage. Changes in VBN was also minimum with an increase of 1.5 mg/100g at $5^{\circ}C$ and 7.0mg/100g at $25^{\circ}C$, but in case of unpacked sample, it was 24.5mg/100g at $5^{\circ}C$ and 42.4 mg/100g at $25^{\circ}C$ even after 7 days. In textural property hardness tended to increase after 28 days and folding test score was down to A or B from AA grade. The loss of available lysine was $7.5\%\;at\;5^{\circ}C$ and $17.0\%\;at\;25^{\circ}C$ but brown color was not deeply developed as the color index score indicated. TBA value was not increased at $5^{\circ}C$ while it tended to increase rapidly after 30 days at $25^{\circ}C$. Changes in TI content was not obvious except that it showed a tendency of increase at the end of storage as well as in the change of lysine and TBA value. It is concluded from the results that the quality of the product, pasteurized and water activity controlled by dielectric heating, and vacuum packed in K-flex film would be stable for more than 35 days at $5^{\circ}C$ and at least 25 days even at room temperature.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.4
• /
• pp.313-324
• /
• 2009

We explore the effect of particle shape and size on 3-dimensional (3D) network and pore structure of porous earth materials composed of glass beads and silica gel using NMR micro-imaging in order to gain better insights into relationship between structure and the corresponding hydrologic and seismological properties. The 3D micro-imaging data for the model porous networks show that the specific surface area, porosity, and permeability range from 2.5 to $9.6\;mm^2/mm^3$, from 0.21 to 0.38, and from 11.6 to 892.3 D (Darcy), respectively, which are typical values for unconsolidated sands. The relationships among specific surface area, porosity, and permeability of the porous media are relatively well explained with the Kozeny equation. Cube counting fractal dimension analysis shows that fractal dimension increases from ~2.5－2.6 to 3.0 with increasing specific surface area from 2.5 to $9.6\;mm^2/mm^3$, with the data also suggesting the effect of porosity. Specific surface area, porosity, permeability, and cube counting fractal dimension for the natural mongolian sandstone are $0.33\;mm^2/mm^3$, 0.017, 30.9 mD, and 1.59, respectively. The current results highlight that NMR micro-imaging, together with detailed statistical analyses can be useful to characterize 3D pore structures of various porous earth materials and be potentially effective in accounting for transport properties and seismic wave velocity and attenuation of diverse porous media in earth crust and interiors.

• Land and Housing Review
• /
• v.2 no.4
• /
• pp.559-568
• /
• 2011

This study aims at listing up those manufacturing activities sensitive to regional characteristics by analyzing locational hierarchy designed on the urban rank-size rule. This locational hierarchy by manufacturing activities is expected to provide a ground for the proper supply of an industrial complex. The analysis of the locational hierarchy by manufacturing activities can work as a method of observing the characteristics of the distribution of location for each economic activity by analyzing the trend in the change of manufacturing location. Consequently, it can be used to determine the appropriate manufacturing activities for the industrial complex of a particular region. Here, the locational hierarchy is analyzed depending on the base of the basic local government such as Gun(district level) and Si(city level), and manufacturing activities are categorized by Korea Standard Industry Code. Those activities demonstrating growth pattern are Manufacture of Electronic Equipment(KSIC 26), Manufacture of Medical Precision Optical Instruments Watch(KSIC 27), Manufacture of Motor Vehicles (KSIC 30, 31), etc. With proper infrastructures, these activities can be located everywhere. Those sectors on the decline pattern in the locational hierarchy can be summarized as Manufacture of Tobacco Products(KSIC 12), Manufacture of wearing apparel Fur Articles(KSIC 14), etc. Those sectors scattered widely in the locational hierarchy are Manufacture of Food Products(KSIC 10), Manufacture of Coke Petroleum Products(KSIC 19), Manufacture of Chemical Products(KSIC 20), Manufacture of Electronic Equipment(KSIC 26). These particular manufacturing activities can be operated in those regions in a sufficient supply of unskilled workers regardless of proper infrastructures. Those activities that have a tendency to reconcentrate on larger cities are Manufacture of Textiles(KSIC 13), Manufacture of Wearing Apparel Clothing Fur Articles(KSIC 14), Manufacture of Other Transport Equiptmen(KSIC 31). In most cases, these sectors tend to favor their existing agglomerated areas and concentrate around large cities. Therefore, it is inefficient to promote these sectors in small or medium-sized cities or underdeveloped regions. The establishment of developmental strategies of an industrial complex can gain greater competitiveness by observing such characteristics of the locational hierarchy.

• Journal of Veterinary Clinics
• /
• v.28 no.5
• /
• pp.486-496
• /
• 2011

A special mesenchymal tissue layer called perichondrium has a chondrogenic capacity and is a candidate tissue for engineering of cartilage. To overcome limited potential for chondrocyte proliferation and re-absorption, we studied a method of cartilage tissue engineering comprising chondrocyte-hydrogel pluronic complex (CPC) and cultured perichondrial cell sheet (cPCs) which entirely cover CPC. For effective cartilage regeneration, cell-sheet engineering technique of high-density culture was used for fabrication of cPCs. Hydrogel pluronic as a biomimetic cell carrier used for stable and maintains the chondrocytes. The human cPCs was cultured as a single layer and entirely covered CPC. The tissue engineered constructs were implanted into the dorsal subcutaneous tissue pocket on nude mice (n = 6). CPC without cPCs were used as a controls (N = 6). Engineered cartilage specimens were harvested at 12 weeks after implantation and evaluated with gross morphology and histological examination. Biological analysis was also performed for glycosaminoglycan (GAG) and type II collagen. Indeed, we performed additional in vivo studies of cartilage regeneration using canine large fullthickness chondrial defect model. The dogs were allocated to the experimental groups as treated chondrocyte sheets with perichondrial cell sheet group (n = 4), and chondrocyte sheets only group (n = 4). The histological and biochemical studies performed 12 weeks later as same manners as nude mouse but additional immunofluorescence study. Grossly, the size of cartilage specimen of cPCs covered group was larger than that of the control. On histological examination, the specimen of cPCs covered group showed typical characteristics of cartilage tissue. The contents of GAG and type II collagen were higher in cPCs covered group than that of the control. These studies demonstrated the potential of such CPC/cPCs constructs to support chondrogenesis in vivo. In conclusion, the method of cartilage tissue engineering using cPCs supposed to be an effective method with higher cartilage tissue gain. We suggest a new method of cartilage tissue engineering using cultured perichondrial cell sheet as a promising strategy for cartilage tissue reconstruction.