• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.6
• /
• pp.567-573
• /
• 2015

This paper aims to evaluate the variation in the mechanical properties of carbon/epoxy composites under in situ low- and high-temperature environments. In situ low- and high-temperature environments were simulated with temperature ranging from $-40^{\circ}C$ to $220^{\circ}C$ using an environmental chamber and furnace. The variation in the mechanical properties of the composites was measured for longitudinal and transverse tensile properties, in-plane shear properties and interlaminar shear strength. Under the low temperature of $-40^{\circ}C$, all mechanical properties increased moderately compared to the baseline properties measured at room temperature. The changes in the longitudinal tensile properties decreased moderately with increasing temperature. However, transverse tensile properties, in-plane shear properties and interlaminar shear strength each showed a significant drop due to the glass transition behavior of the matrix after $140^{\circ}C$. Notably, the tensile property value near $100^{\circ}C$ increased compared to baseline property value, which was an unusual occurrence. This behavior was a direct result of post-curing of the epoxy resin due to its exposure to high temperature.

• Journal of Korean Society for Atmospheric Environment
• /
• v.23 no.5
• /
• pp.547-556
• /
• 2007

The release, sampling and analytical methods have been developed and tested for perfluorocarbons (PFCs) atmospheric tracers in order to gain insight into the atmospheric transport and dispersion over the urban conditions of Seoul, Korea. Although PFCs tracer experiments provide unique opportunities to test local and urban scale of transport and dispersion, no previous experiment with PFCs has been conducted in Korea. PMCH and PDCH were chosen as targeted tracers in our study due to their extreme low ambient concentrations and great sensitivities among various PFCs. For PFCs release system, a set of micro-metering pump, electronic balance, vaporizing furnace and high speed blower was constructed for precise and accurate release of tracers. The precision of released rate by this system was estimated to be 1%. Samplings of PFCs were carried out by fabricated portable air samplers with micro pumps and rotameters into glass tubes packed with 150 mg of Carboxen-569. The uncertainty of these sampling system was maintained below 14%. PMCH and PDCH were quantified in GC/ECD with preconditioned injection system to eliminate the interference compounds using traps and subsequent catalytic conversion system prior to column separation. Three intensive field test were undertaken during the springtime of 2002 to 2004 in eastern part of Seoul. Daily background samples were collected to characterize the background levels of PMCH and PDCH prior to their release. The observed background concentrations of PMCH ranged from 3.5 to 10.1 fL/L and varied randomly in location and time in this study. Its mean and standard variation of background concentration ($6.8{\pm}1.9\;fL/L$) are higher than those ($3.2{\sim}5.8\;fL/L$) of other historic tracer studies. Identified uncertainty for background PMCH was $1.7{\sim}2.0\;fL/L$ using this analytical system. Combined relative uncertainty in determining the tracer's concentrations was estimated as 17%. However, its background concentrations and uncertainty in concentration determination were found to be low and stable enough for tracer study.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.143-144
• /
• 2010

3-5족 화합물 반도체를 이용한 집광형 삼중 접합 태양전지는 40% 이상의 광변환 효율로 많은 주목을 받고 있다[1]. 삼중 접합 태양전지의 하부 셀은 기계적 강도가 높고 장파장을 흡수할 수 있는 Ge이 사용된다. Ge위에 성장될 III-V족 단결정막으로서 Ge과 격자상수가 일치하는 GaInP나 GaAs가 적합하고, 성장 중 V족 원소의 열확산으로 인해 Ge과 pn접합을 형성하게 된다. 이때 GaInP의 P의 경우 GaAs의 As보다 확산계수가 낮아 태양전지 변환효율향상에 유리한 얇은 접합 형성이 가능하고, 표면 에칭효과가 적기 때문에 GaInP를 단결정막으로 선택하여 p-type Ge기판 위 성장으로 단일접합 Ge구조 제작이 가능하다. 하지만 이종접합 구조 성장으로 인해 발생한 계면사이의 전위나 미세결함들이 결정막내부에 존재하게 되며 이러한 결함들은 광학소자 응용 시 비발광 센터로 작용할 뿐 아니라 소자의 누설전류를 증가시키는 원인으로 작용하여 태양전지 변환효율을 감소시키게 된다. 이에 결함감소를 통해 소자의 전기적 특성을 향상시키고자 수소 열처리나 플라즈마 공정을 통해 수소 원자를 박막내부로 확산시키고, 계면이나 박막 내 결함들과 결합시킴으로서 결함들의 비활성화를 유도하는 연구가 많이 진행되어 왔다 [2][3]. 하지만, 격자불일치를 갖는 GaInP/Ge 구조에 대한 수소 열처리 및 불순물 준위의 거동에 대한 연구는 많이 진행되어 있지 않다. 따라서 본 연구에서는 Ga0.45In0.55P/Ge구조에 수소 열처리 공정을 적용을 통하여 단결정막 내부 및 계면에서의 결함밀도를 제어하고 이를 통해 태양 전지의 변환효율을 향상시키고자 한다. <111> 방향으로 $6^{\circ}C$기울어진 p-type Ge(100) 기판 위에 유기금속화학증착법 (MOCVD)을 통해 Si이 도핑된 200 nm의 n-type GaInP층을 성장하여 Ge과 단일접합 n-p 구조를 제작하였다. 제작된 GaInP/Ge구조를 furnace에서 250도에서 90~150분간 시간변화를 주어 수소열처리 공정을 진행하였다. 저온 photoluminescence를 통해 GaInP층의 광학적 특성 변화를 관찰한 결과, 1.872 eV에서 free-exciton peak과 1.761 eV에서 Si 도펀트 saturation에 의해 발생된 D-A (Donor to Acceptor)천이로 판단되는 peak을 검출할 수 있었다. 수소 열처리 시간이 증가함에 따라 free-exciton peak 세기 증가와 반가폭 감소를 확인하였고, D-A peak이 사라지는 것을 관찰할 수 있었다. 이러한 결과는 수소 열처리에 따른 단결정막 내부의 수소원자들이 얕은 불순물(shallow impurity) 들로 작용하는 도펀트들이나, 깊은 준위결함(deep level defect)으로 작용하는 계면근처의 전위, 미세결함들과의 결합으로 결함 비활성화를 야기해 발광세기와 결정질 향상효과를 보인 것으로 판단된다. 본 발표에서는 상술한 결과를 바탕으로 한 수소 열처리를 통한 박막 및 계면에서의 결함준위의 거동에 대한 광분석 결과가 논의될 것이다.

• Korean Journal of Materials Research
• /
• v.25 no.2
• /
• pp.75-80
• /
• 2015

The carbon dioxide($CO_2$) released while producing building materials is substantial and has been targeted as a leading contributor to global climate change. One of the most typical method to reducing $CO_2$ for building materials is the addition of slag and fly ash, like pozzolan material, while another method is reducing $CO_2$ production by carbon negative cement development. The MgO-based cement was from the low-temperature calcination of magnesite required less energy and emitted less $CO_2$ than the manufacturing of Portland cements. It is also believed that adding reactive MgO to Portland-pozzolan cements could improve their performance and also increase their capacity to absorb atmospheric $CO_2$. In this study, the basic research for magnesia cement using $MgCO_3$ and magnesium silicate ore (serpentine) as main starting materials, as well as silica fume, fly ash and blast furnace slag for the mineral admixture, were carried out for industrial waste material recycling. In order to increase the hydration activity, $MgCl_2$ was also added. To improve hydration activity, $MgCO_3$ and serpentinite were fired at $700^{\circ}C$ and autoclave treatment was conducted. In the case of $MgCO_3$ as starting material, hydration activity was the highest at firing temperature of $700^{\circ}C$. This $MgCO_3$ was completely transferred to MgO after firing. This occurred after the hydration reaction with water MgO was transferred completely to $Mg(OH)_2$ as a hydration product. In the case of using only $MgCO_3$, the compressive strength was 3.5MPa at 28 days. The addition of silica fume enhanced compressive strength to 5.5 MPa. In the composition of $MgCO_3$-serpentine, the addition of pozzolanic materials such as silica fume increased the compression strength. In particular, the addition of $MgCl_2$ compressive strength was increased to 80 MPa.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.1031-1037
• /
• 1998

To investigate the effect of cooling rate and annealing temperature on the corrosion of Zircaloy-4 and Zr-2. 5Nb alloys, autoclave corrosion tests were performed at $500^{\circ}C$ for the specimens prepared by various heat treatments. The specimens were heat-treated at $1050^{\circ}C$ for 30 minutes and cooled by ice-brine quenching, water quenching, oil quenching, air cooling, and furnace cooling. To investigate the effect of annealing temperature, the specimens were annealed at $\alpha$, ($\alpha$+$\beta$)-, and $\beta$-temperatures. It was observed from the $500^{\circ}C$ corrosion test that nodular corrosion occurred on the Zircaloy-4 alloy but did not occur on the Zr-2.5Nb alloy. The corrosion resistance of Zircaloy-4 increased with increasing the cooling rate. On the other hand, the corrosion resistance of Zr-2.5Nb decreased with increasing the cooling rate and the annealing temperature. It is suggested that corrosion resistance of Zircaloy-4 would be controlled by the distribution of Fe and Cr element in the matrix and precipitates, while that of Zr-2.5Nb alloy the niobium concentration and $\beta_{-Nb}$ phase.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.352-356
• /
• 2003

A stoichiometric mixture of evaporating materials for $CuGaSe_2$ single crystal am films was prepared from horizontal electric furnace. Using extrapolation method of X-ray diffraction patterns for the polycrystal $CuGaSe_2$, it was found tetragonal structure whose lattice constant $a_0$ and $c_0$ were $5.615\;{\AA}\;and\;11.025\;{\AA}$, respectively. To obtain the single crystal thin films, $CuGaSe_2$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the hot wall epitaxy (HWE) system. The source and substrate temperatures were $610^{\circ}C$ and $450^{\circ}C$, respectively, The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of $CuGaSe_2$ single crystal thin films measured with Hall effect by van der Pauw method are $9.24{\times}10^{16}\;cm^{-3}$ and $295\;cm^2/V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of the $CuGaSe_2$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)\;:\;1.7998\;eV\;-\;(8.7489\;{\times}\;10^{-4}\;eV/K)T^2(T\;+\;335\;K)$. After the as-grown $CuGaSe_2$ single crystal thin films was annealed in Cu-, Se-, and Ga-atmospheres, the origin of point defects of $CuGaSe_2$ single crystal thin films has been investigated by the photoluminescence(PL) at 10 K. The native defects of $V_{CU}$, $V_{Se}$, $CU_{int}$, and $Se_{int}$, obtained by PL measurements were classified as a donors or accepters type. And we concluded that the heat-treatment in the Cu-atmosphere converted $CuGaSe_2$ single crystal thin films to an optical n-type. Also, we confirmed that Ga in $CuGaSe_2/GaAs$ did not form the native defects because Ga in $CuGaSe_2$ single crystal thin films existed in the form of stable bonds.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.2
• /
• pp.203-210
• /
• 2012

Recently, the interest and demand for large-scale buildings and skyscrapers have been on the rise, and the performance of concrete is an area of high priority. Securing 'mass concrete and high strength concrete' is very important as a key construction technology. For high strength concrete, the high heat of hydration takes place inside the concrete because of the vitality of hydration in cement due to the large amount of powder, and leads to problems such as an increase of thermal stress due to the temperature difference with the outside, which results in cracks and slump loss. For this reason, measures to solve these problems are needed. This study aims to reduce the hydration heat of high strength concrete to control the hydration heat of mass concrete and high strength concrete, by replacing the type of admixture, The purpose of this study is to control the hydration heat of high strength concrete and mass concrete. Our idea for this purpose is to apply not only the types and contents of admixture but also incorporation mixing water to ice-flake. As a result of the test, the use of blast furnace slag and fly ash as admixture, and the use of ice-flake as mixing water can improve the liquidity of concrete and reduce slump loss. Significantly dropping the maximum temperature will contribute greatly to reducing cracks due to hydration heat in mass concrete and high strength concrete, and improve quality.

• Resources Recycling
• /
• v.25 no.2
• /
• pp.60-68
• /
• 2016

In this study, earlier analyzed tetrapod, one of an original group of offshore constructions studied for manufacturability of the concrete using the properties of steel making slag aggregate. steel making slag aggregate assessment, RCS and Blast Furnace Slag : the 20 mm air-cooled slag and combinations by 50 %, aggregate properties on the most appropriate for the properties of recycled aggregate concrete optimal mix, and assessing it. Properties of concrete used to be derived are judged as to bury the studies show that the hollowing-out of the RCS, plastic sole use is in the workability of the aggregate, plastic in the 20 mm slag also assessed to be a slight disadvantage, but RCS by mixing air-cooled coarse and 50 percent to 20 percent 50 mm. Thus, steel making slag marine structures using recycled aggregate, in rapid chilled slag or air-cooled slag. The sole use of the aggregate them than to combine the aggregate of concrete. After they satisfy the quality standard quality shall be used will aggregate steel making slag who meet the criteria concrete manufacturing in general or par with the aggregate of concrete. Performance was assessed as to develop a more than that.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.57-64
• /
• 2017

Today, due to the environmental regulations regarding air pollution in the EU, the use of EPS (Styrofoam) as the cushioning material in the packaging industry is decreasing. In effect, air cushioning based cushioning materials are rapidly expanding into the market and replacing EPS, due to their excellent buffering ability and environmental friendliness. This is a new selective filling type air filling material manufacturing technology that affords improvements in the amount of raw materials required, its processing and its aesthetic appearance compared to the conventional air filling cushioning materials. In this study, a multi-stage air cell filling valve molding technology is developed based on selective filling technology, which allows packages to be selectively filled in various forms by applying valve forming structure technology. This multi-stage air cell filling valve molding technology is a technique in which a plurality of injection ports are formed by laminating three layers of films, viz. a first injection film, a valve film, and a second injection film having valve ends. In the conventional technology, a separate external air injection path for injecting air into a plurality of connected air bags is needed. However, in the proposed system, an external air injection path is formed inside the air bag, Due to the lack of need for an injection furnace, the raw material and process are reduced and air is injected and then discharged, while the air bag is reduced in length to 63 ~ 66% of its normal value. The outer surface of the outer air injection path is integrated inside by maintaining the original length of the cross section, while the unnecessary folded air is injected into the interior of the air bag, This smart air filling type cushioning material manufacturing technology constitutes a big improvement over the existing technologies.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.536-542
• /
• 2018

Tin dioxide, $SnO_2$, is a well-known n-type semiconductor that shows change in resistance in the presence of gas molecules, such as $H_2$, CO, and $CO_2$. Considerable research has been done on $SnO_2$ semiconductors for gas sensor applications due to their noble property. The nanomaterials exhibit a high surface to volume ratio, which means it has an advantage in the sensing of gas molecules. In this study, SnO nanoplatelets were grown densely on Si substrates using a thermal CVD process. The SnO nanostructures grown by the vapor transport method were post annealed to a $SnO_2$ phase by thermal CVD in an oxygen atmosphere at $830^{\circ}C$ and $1030^{\circ}C$. The pressure of the furnace chamber was maintained at 4.2 Torr. The crystallographic properties of the post-annealed SnO nanostructures were investigated by Raman spectroscopy and XRD. The change in morphology was confirmed by scanning electron microscopy. As a result, the SnO nanostructures were transformed to a $SnO_2$ phase by a post-annealing process.