• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.11
• /
• pp.1075-1086
• /
• 2008

In order to investigate the applicability and suitability of the industrial by-products to apply mono-layer cover system for non-sanitary landfill sites, 6 different industrial by-products, such as construction waste, bottom ash, gypsum, blast furnace and steel manufacture slags, and stone powder sludge, were evaluated. Various physicochemical and hydrodynamic properties of the industrial byproducts were investigated. The environmental safety was monitored using batch and long-term leaching tests as well. In addition, the flexibility of plants was observed by cultivating them in the industrial by-products. The results for physicochemical properties indicate that most of the materials considered appeared to be suitable for landfill cover. Particularly, the concentration levels of hazardous elements regulated by the Korean Law for Waste Management did not exceed the regulatory limits in all target materials. In addition, the concentrations of regulated elements for the Korean Soil Conservation Law were examined below the regulatory limits in most of materials considered, except for the stone powder sludge. The results of batch and long-term experiments showed bottom ash and construction waste were the most suitable materials for landfill cover among the industrial by-products considered. The results of plant studies indicate that the bottom ash among industrial by-products considered was most effective in developing vegetation on landfill site, showing fast germination and large growth index. At the final covering system made of mixture of soil and bottom ash, the optimum application rate of farmyard manure was observed to be 40-50 Mg/ha.

• Journal of Conservation Science
• /
• v.36 no.2
• /
• pp.143-151
• /
• 2020

In the present article, we have analyzed five slags excavated from the Unified Silla period iron smelting site, i.e., location 4-2 of the Inje Bupyeong-ri site, to investigate the iron smelting process. The total Fe content of the slag excavated from the Inje Bupyeong-ri site ranged between 3.65 and 23.78 wt%, lower than that of typical slag, and deoxidation agent of the slag ranged between 65.92 and 88.96 wt%, higher than that of typical slag. These results suggest that the recovery rate of iron was significantly high. Furthermore, cristobalite was detected in most of the samples, and the furnace temperature, estimated by substituting the analyzed data into the FAS and FCS state diagrams, was confirmed as 1,600℃ or more. These results suggest that the operation at the Inje Bupyeong-ri site was performed at a temperature capable of producing cast iron by completely melting the carbon-containing iron. Observation of the microstructure showed that the iron fragments excavated at the Inje Bupyeong-ri site were identified as white cast iron. Steadite from the ternary iron-carbon-phosphorus system was observed in the white cast iron structure. These results show that indirect smelting was performed when the iron smelting by-products were produced. Based on the analysis results, it was confirmed that the Inje Bupyeong-ri site was the indirect smelting site in the Unified Silla period.

• Analytical Science and Technology
• /
• v.23 no.1
• /
• pp.45-53
• /
• 2010

For the determination of chlorine in uranium compound, analytical methods by using a steam distillation and a pyrohydrolysis have been developed. The steam distillation apparatus was composed of steam generator, distilling flask and condenser etc. The samples were prepared with an aliquot of LiCl standard solution and a simulated spent nuclear fuel. A sample aliquot was mixed with a solution containing 0.2 M ferrous ammonium sulfate-0.5 M sulfamic acid 3 mL, phosphoric acid 6 mL and sulfuric acid 15 mL. The chloride was then distilled by steam at the temperature of $140^{\circ}C$ until a volume of $90{\pm}5\;mL$ is collected. The pyrohydrolysis equipment was composed of air introduction system, water supply, quartz reaction tube, combustion tube furnace, combustion boat and absorption vessel. The chloride was separated from powdered sample which is added with $U_3O_8$ accelerator, by pyrohydrolysis at the temperature of $950^{\circ}C$ for 1 hour in a quartz tube with a stream of air of 1 mL/min supplied from the water reservoir at $80^{\circ}C$. The chlorides collected in each absorption solution by two methods was diluted to 100 mL and measured with ion chromatography to determine the recovery yield. For the ion chromatographic determination of chlorine in molten salt retained in a metal ingot, the chlorine was separated by means of pyrohydrolysis after air and dry oxidation, and grinding for the sample.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.661-671
• /
• 2018

Domestic studies on steel plate concrete structures have focused on nuclear structures with high strength. In this study, the SC structure was applied to the general structure, and the SC structure that is advantageous in terms of safety and construction was limited to a special structure. As a basic study for applying SC, this paper proposes basic design information of a SC structure applying cement concrete to plan the structure, which is suitable for eco - friendliness by replacing concrete cement, an important factor in a SC structure, with blast furnace slag. This study examined the compression characteristics and the effective length factor under central compression load. To calculate the effective length factor, the Euler column theory was applied without applying plate theory. The effective length factor was calculated from the yield strength of the steel plate, buckling of the steel plate, and the point at which the concrete was broken. In addition, this study examined whether the maximum compressive strength meets the national and international reference equations with the slenderness ratio (B/t) as a parameter. By analyzing the buckling of the specimen by applying the column theory and selecting the strain of the measured steel plate, the effective length factor was analyzed and compared with the value presented in the reference equation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.2
• /
• pp.1005-1012
• /
• 2011

This research carried out a 3-dimensional simulation using computerized fluid dynamics (CFD) for the flow characteristics, temperature distribution, velocity distribution and residence time, etc. in a reactor in order to derive the optimal combustion conditions of an innovative combustion system. The area-weighted average temperature of the outlet of a furnace during combustion at a condition of fuel input rate 1.5 ton/hr, residence time 1.25 sec and air/fuel ratio 2.1 was $1,077^{\circ}C$, which is a suitable temperature for energy recovery and treatment of air pollutants. Exhaust gas is discharged through a duct at a 40~50 m/s maximum speed along strong vortexes at the center of a combustion chamber, so strong turbulence is created at the center of a combustion chamber to enhance the combustion speed and combustion efficiency. In this system, the optimum operation conditions to prevent incomplete combustion and suppress the formation of thermal NOx were air/fuel ratio 1.9~2.1 and fuel input rate 1.25~1.5 ton/hr.

• Journal of Yeungnam Medical Science
• /
• v.6 no.2
• /
• pp.147-157
• /
• 1989

To investigate the blood lead concentration, their interrelation, correlation factor and influence on pregnant women and newborn, lead concentration in the maternal blood and umbilical cord blood were determined. Samples were collected from 130 mothers who were living in the Taegu City, during March, 1989. Blood lead concentration was estimated using the Atomic Absorption Spectrophotometer(IL. 551) equipped with Flameless Furnace Atomizer (IL. 665). The mean lead concentration of maternal and cord blood were $17.47{\pm}7.92{\mu}g/d{\ell}$, $15.31{\pm}7.98{\mu}g/d{\ell}$, respectively. A significant correlation was observed between the lead concentration of maternal and cord blood, r=0.663, Y=0.667X+3.646. No significant correlation was observed between previous spontaneous abortion and obstetric complication of mother and maternal blood lead concentration. Similarly, no significant correlation was observed between the sex, gestational age of neonate and cord blood lead concentration. But the birth weight of neonate had some negative correlation with cord blood lead concentration. The blood lead concentration of mother who had engaged in manufactures were higher than others and the longer working years were, the higher blood lead concentration were. Significant correlation was observed between husband's occupational exposure to lead and maternal blood lead concentration.

• Korean Chemical Engineering Research
• /
• v.58 no.4
• /
• pp.588-595
• /
• 2020

Prediction and control of nitrogen oxides (NO_x) emission is of great interest in industry due to stricter environmental regulations. Herein, we propose an artificial intelligence (AI)-based framework for prediction of NO_x emission. The framework includes pre-processing of data for training of neural networks and evaluation of the AI-based models. In this work, Long-Short-Term Memory (LSTM), one of the recurrent neural networks, was adopted to reflect the time series characteristics of NO_x emissions. A decision tree was used to determine a time window of LSTM prior to training of the network. The neural network was trained with operational data from a heating furnace. The optimal model was obtained by optimizing hyper-parameters. The LSTM model provided a reliable prediction of NO_x emission for both training and test data, showing an accuracy of 93% or more. The application of the proposed AI-based framework will provide new opportunities for predicting the emission of various air pollutants with time series characteristics.

• Resources Recycling
• /
• v.9 no.1
• /
• pp.52-62
• /
• 2000

In order to maximize the recycling of converter slag to the more valuable fields, such as high quality aggregates for construction, cement industry and flux for ion making. It will be very important to control the compositions and properties of converter slag to suit the purpose of utilizastion. In this study, converter slag (STELCO, CANADA) was mixed with 5%~30% $SiO_2$and 7% carbon, and then reduced at $1650^{\circ}C$. After the reduction was completed, the reformed slags were cooled to room temperature in the furnace. All of the slags were then characterized using SEM-EDX, XRD and chemical analysis. Also the compressive strengths and densities of the reformed slags were measured to compare with natural aggregates. XRD analysis shows that th phases of reformed slags are changed from bredigite+merwinite mixed phases of 10% $SiO_2$added reduction to akermanite phases of 20% and 30% $SiO_2$ added reduction. But the SEM-EDX analysis revealed that the phase distribution of the reformed slags was changed very sensitively and complicately depends on the change of slag compositions. And also the properties of reformed slags are changed very much depend on the phase distribution. About one third of Cadmium and on fifth of Vanadium are remained in reduction reformed converter slag. Another heavy metal elements such as cobalt, zinc, lead are removed up to more than 90-95% of original slag. The compressive strength and density of 25% $SiO_2$ added and reformed slag is very near to natural granite. This is superior more than 10% to Thyssen's $SiO_2$ added and oxidized converter slag aggregates.

• Resources Recycling
• /
• v.23 no.2
• /
• pp.61-70
• /
• 2014

LCD televisions and monitors use cold cathode fluorescence lamps (CCFLs) to illuminate the screen. Most CCFLs contain mercury and they have to be carefully handled at the end of their lives as per minimum treatment standards under the Waste Electrical and Electronic Equipment (WEEE) and Restriction of Hazardous Substances (RoHS) directives. CCFLs were carefully separated from mold frames of waste LCD units for primary decontamination of mercury/fluorescent compound mixture using CCFL decontamination system designed and fabricated in the present research. Residual mercury was further removed by employing a pyro-process, where crushed CCFL tubes transferred from primary decontamination process were subject to heat treatment at $550^{\circ}C$ in a box furnace: more than 99% of mercury was removable from waste CCFLs.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.4
• /
• pp.1-8
• /
• 2006

Anatomy of Quercus variabilis charcoal was investigated by scanning electron microscopy. Charcoal was prepared in an electric furnace under nitrogen gas atmosphere at $400^{\circ}C$, $600^{\circ}C$, $800^{\circ}C$, and $1000^{\circ}C$ for 10 min. The structure of charcoal was significantly affected by charring temperature. In cross section, charcoal prepared at $400^{\circ}C$ exhibited a smooth clean surface. As the charring temperature increased, the surface became more rough and increasingly disrupted. The cell walls appeared homogeneous and glass-like. Ray parenchyma cells showed very little separation from each other in radial section at $400^{\circ}C$. At $600^{\circ}C$ and above there is an apparent disintegration of the middle lamella, resulting in a separation of the ray cells. The $2{\sim}4{\mu}m$ wart-like protuberances were observed on the surfaces of the parenchyma cells. These structures were seen in charcoal prepared at all temperatures. Distinctive features can be seen in multiseriate rays as large crack and split. Rhomboidal crystals in crystalliferous cells had a smooth surface at $400^{\circ}C$ and $600^{\circ}C$, but the crystals had a sponge like appearance at $800^{\circ}C$ and $1000^{\circ}C$.