• ETRI Journal
• /
• v.34 no.1
• /
• pp.17-23
• /
• 2012

This paper analyzes the feasibility of a new 3DTV broadcasting service scenario via Advanced Television Systems Committee Mobile/Handheld (ATSC-M/H). We suggest a dual-channel system in which a left-view image is encoded by MPEG-2 with HD quality and a small-sized right-view image is encoded by AVC. Also, the left view is transmitted through ATSC main channel and the right view is transmitted through ATSC-M/H channel. Although the transport stream formats of two channels are different from each other, we demonstrate that it is possible for the ATSC 2.0 decoder to synchronize the display of the left and right views when both encoders use a common wall clock and time stamp. We also propose a program specific information descriptor which guarantees full compatibility with the conventional 2D HDTV and emerging mobile TV services. Finally, we provide the results of subjective visual quality assessment of the proposed system in support of its 3DTV service quality.

• Korean Journal of Optics and Photonics
• /
• v.25 no.1
• /
• pp.21-28
• /
• 2014

In this paper a Super Multi-view display method using a pinhole array with full parallax was proposed. The proposed method was simulated and its parameters analyzed. Also, the distribution and irradiance of light through each pinhole on the retina receiver, according to the change of crystalline lens focal length, were found by simulation. As a result, an image free of blurring was obtained while the crystalline lens focused on the depth plane of the three-dimensional image created by the imaging lens.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.413-414
• /
• 2008

We have studied an organic layer thickness dependent optical properties and microcavity effects for top-emission organic light-emitting diodes. Manufactured top emission device, structure is Al(100nm)ITPD(xnm)/$Alq_3$(ynm)/LiF(0.5nm)/Al(23nm). While a thickness of hole-transport layer of TPD was varied from 35 to 65nm, an emissive layer thickness of $Alq_3$ was varied from 50 to 100nm for two devices. A ratio of those two layers was kept to about 2:3. Variation of the layer thickness changes a traverse time of injected carriers across the organic layer, so that it may affect on the chance of probability of exciton formation. View-angle dependent emission spectra were measured for the optical measurements. Top-emission devices show that the emission peak wavelength shifts to longer wavelength as the organic layer thickness increases. For instance, it shifts from 490 to 555nm in the thickness range that we used. View-angle dependent emission spectra show that the emission intensity decreases as the view-angle increases. The organic layer thickness-dependent emission spectra show that the full width at half maximum decreases as the organic layer thickness increases. Top emission devices show that the full width at half maximum changes from 90 to 35nm as the organic layer thickness increases. In top-emission device, the microcavity effect is more vivid as the organic layer thickness increases.

• Journal of Biomedical Engineering Research
• /
• v.35 no.5
• /
• pp.151-159
• /
• 2014

Computed tomography (CT) is one of the most widely used medical imaging modality. However, substantial x-ray dose exposed to the human subject during the CT scan is a great concern. Region-of-interest (ROI) CT is considered to be a possible solution for its potential to reduce the x-ray dose to the human subject. In most of ROI-CT scans, the ROI is set to a circular shape whose diameter is often considerably smaller than the full field-of-view (FOV). However, an arbitrarily shaped ROI is very desirable to reduce the x-ray dose more than the circularly shaped ROI can do. We propose a new method to make a non-circular convex-shaped ROI along with the image reconstruction method. To make a ROI with an arbitrary convex shape, dynamic collimations are necessary to minimize the x-ray dose at each angle of view. In addition to the dynamic collimation, we get the ROI projection data with slightly lower sampling rate in the view direction to further reduce the x-ray dose. We reconstruct images from the ROI projection data in the compressed sensing (CS) framework assisted by the exterior projection data acquired from the pilot scan to set the ROI. To validate the proposed method, we used the experimental micro-CT projection data after truncating them to simulate the dynamic collimation. The reconstructed ROI images showed little errors as compared to the images reconstructed from the full-FOV scan data as well as little artifacts inside the ROI. We expect the proposed method can significantly reduce the x-ray dose in CT scans if the dynamic collimation is realized in real CT machines.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.4
• /
• pp.366-373
• /
• 2005

This paper presents two new circuit topologies of the dc busline side active resonant snubber assisted voltage source high frequency link soft switching PWM full-bridge dc-dc power converters acceptable for either utility ac 200V-rms or ac 400V-rms input grid. These high frequency switching dc-dc converters proposed in this paper are composed of a typical voltage source-fed full-bridge PWM inverter, high frequency transformer with center tap, high frequency diode rectifier with inductor input filter and dc busline side series switches with the aid of a dc busline parallel capacitive lossless snubber. All the active switches in the full-bridge arms as well as dc busline snubber can achieve ZCS turn-on and ZVS turn-off transition commutation with the aid of a transformer leakage inductive component and consequently the total switching power losses can be effectively reduced. So that, a high switching frequency operation of IGBTs in the voltage source full bridge inverter can be actually designed more than about 20 kHz. It is confirmed that the more the switching frequency of full-bridge soft switching inverter increases, the more soft switching PWM dc-dc converter with a high frequency transformer link has remarkable advantages for its power conversion efficiency and power density implementations as compared with the conventional hard switching PWM inverter type dc-dc power converter. The effectiveness of these new dc-dc power converter topologies can be proved to be more suitable for low voltage and large current dc-dc power supply as arc welding equipment from a practical point of view.

• International Journal of Automotive Technology
• /
• v.2 no.4
• /
• pp.147-155
• /
• 2001

Analysis of the thermodynamic cycle of IC engine from the point of view of economy and emissions was carried out. From this analysis potential capability of engine development was derived. This potential capability is lean-burn engine, fuelled with homogeneous mixture with $\lambda \geq$ 1.4. Several different modes of fuelling were proposed and tested on one-cylinder test engine from the point of view of extending lean operating limit of the engine, emissions and fuel economy. Among them were: fuelling with evaporated preheated gasoline, with gas (LPG evaporated) and with liquid butane. From these modes, fuelling with liquid butane injected to inlet port was selected and finally tested. This novel system of fuelling offered better than standard engine performances and emissions at lean operating limit. These results were validated on full-scale two-cylinder engine.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.27
• /
• pp.29-65
• /
• 2005

Northeast Asian economies have achieved high levels of growth due to a stable economic environments and economic policy reforms for free trade. As Northeast Asia has been risen as big bloc in the world and in the future in case free trade agreement could be concluded, trade volume could be increased dramatically. And it is evident that disputes will be increased in Northeast Asian economic bloc. Arbitration must be popular in resolving international commercial disputes in Northeast Asian bloc in order to increase the volume of intra-trade in the bloc. Through arbitration, the parties can have full autonomy and can resolve disputes independently, impartially and without delay. But in order for the parties to make use of arbitration in the bloc, they must be fully aware of the arbitration laws of Northeast Asian nations in view of the similarity and difference of the laws. Therefore, this paper deals with arbitral award in Northeast Asian Nations' arbitration laws in view of comparative law.

• 한국정보컨버전스학회:학술대회논문집
• /
• 2008.06a
• /
• pp.103-110
• /
• 2008

In this thesis, we describe a statistical method for 3D object detection. In this method, we decompose the 3D geometry of each object into a small number of viewpoints. For each viewpoint, we construct a decision rule that determines if the object is present at that specific orientation. Each decision rule uses the statistics of both object appearance and "non-object" visual appearance. We represent each set of statistics using a product of histograms. Each histogram represents the joint statistics of a subset of wavelet coefficients and their position on the object. Our approach is to use many such histograms representing a wide variety of visual attributes. Using this method, we have developed the first algorithm that can reliably detect faces that vary from frontal view to full profile view and the first algorithm that can reliably detect cars over a wide range of viewpoints.

• ETRI Journal
• /
• v.36 no.2
• /
• pp.264-270
• /
• 2014

This paper introduces a novel repetitive delivery scheme for the left and right views in service-compatible (SC) 3D video that provides full backward compatibility to a legacy DTV system while retaining HD 3D visual quality without additional bandwidth or a codec over the legacy broadcasting channel. The proposed SC delivery scheme transmits individual view sequences of a 3D video in interlaced form, that is, a left-view sequence of a 3DTV program to be used repeatedly is transmitted first and stored locally, and the right-view sequence of the 3D program is then transmitted. This paper specifically describes the signaling, synchronization, and storage format methods used to validate the proposed SC delivery scheme. The experiment results show that the proposed SC delivery scheme can be effectively applied for an SC 3DTV service without degrading the DTV quality using only legacy DTV platforms.

• ETRI Journal
• /
• v.39 no.1
• /
• pp.97-107
• /
• 2017

A fast and accurate building-level visual place recognition method built on an image-retrieval scheme using street-view images is proposed. Reference images generated from street-view images usually depict multiple buildings and confusing regions, such as roads, sky, and vehicles, which degrades retrieval accuracy and causes matching ambiguity. The proposed practical database refinement method uses informative reference image and keypoint selection. For database refinement, the method uses a spatial layout of the buildings in the reference image, specifically a building-identification mask image, which is obtained from a prebuilt three-dimensional model of the site. A global-positioning-system-aware retrieval structure is incorporated in it. To evaluate the method, we constructed a dataset over an area of $0.26km^2$. It was comprised of 38,700 reference images and corresponding building-identification mask images. The proposed method removed 25% of the database images using informative reference image selection. It achieved 85.6% recall of the top five candidates in 1.25 s of full processing. The method thus achieved high accuracy at a low computational complexity.