• Structural Engineering and Mechanics
• /
• 제74권4호
• /
• pp.559-565
• /
• 2020

This paper intends to progress models to accurately estimate the behavior of fresh concrete under vibration using artificial neural networks (ANNs). To this end, behavior of a full scale precast concrete mold was investigated numerically. Experimental study was carried out under vibration with the use of a computer-based data acquisition system. In this study measurements were taken at three points using two vibrators. Transducers were used to measure time-dependent lateral displacements at these points on mold while both mold is empty and full of fresh concrete. Modeling of empty and full mold was made using ANNs. Benefiting ANNs used in this study for modeling fresh concrete, mold design can be performed. For the modeling of ANNs: Experimental data were divided randomly into two parts such as training set and testing set. Training set was used for ANN's learning stage. And the remaining part was used for testing the ANNs. Finally, ANN modeling was compared with measured data. The comparisons show that the experimental data and ANN results are compatible.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.717-718
• /
• 2011

• 대한산업공학회지
• /
• 제19권4호
• /
• pp.71-86
• /
• 1993

In design stage of a plastic injection mold, basic entities of various kinds are introduced under the concept of Group Technology to produce a full drawings of the mold more effectively Most of the entity data should be extracted from the assembly drawing by pattern matching technique. An automated design system is developed using the extracted data of entities and thus shows a good interfaces between the design stage and producing part explosion without any manual conversion procedure under the AutoCAD environment.

• 한국공작기계학회논문집
• /
• 제17권5호
• /
• pp.82-88
• /
• 2008

Conventional aspherical lens polishing methods by the small tool polishing use aspherical profile and the trajectory of the polishing tool is also controlled. In this paper, new full contact polishing mechanism is suggested to polish aspherical glass lens mold by both airbag polishing tool and eccentric motion. Full contact concept by airbag polishing tool and no position control make the easy polishing setup and do not need aspherical design profile. An aspherical lens polishing machine was made for this study and a verification experiment was performed for surface roughness improvements.

• Design & Manufacturing
• /
• 제17권3호
• /
• pp.61-66
• /
• 2023

In this study, we developed a simulation methodology for a technology that rapidly cools molds by directly spraying them with CO₂ in its liquefied gaseous state. Initially, a simulation verification process was conducted using ANSYS Fluent's heat transfer analysis based on temperature values measured in prior research experiments, ensuring a comparable temperature could be calculated. Subsequently, the validated analysis method was employed to evaluate design factors that exert the most significant influence on cooling. An evaluation was conducted based on three factors: part thickness, mold thickness, and the melting temperature of material. Using a full factorial design approach, a total of 27 analyses were completed and subsequently calculated through analysis of means. The impact assessment was carried out based on the temperature values at the product's core. The results indicated that the thickness of the mold had the highest influence, while the melting temperature of material had the least.

• 한국약용작물학회지
• /
• 제23권1호
• /
• pp.43-48
• /
• 2015

This study was carried out in order to investigate the photosynthesis response and leaf characteristics of Peucedanum japonicum growing in forest farming. The experiment was performed by leaf mold (pine tree and chestnut tree) and shading levels (0%, 35%, 50% and 75% shading). Light relative intensity was 100% (full sunlight), 60.3% (35% shading), 35.1% (50% shading), and 17.4% (75% shading) respectively. Light response curves of pine-leaf mold and chestnut-leaf mold were the highest in control (full sunlight) and these were getting lower in the higher shading level. Photosynthesis capacity and light saturation point were indicated higher in chestnut-leaf mold within the same shading level. As the shading level increased, maximum photosynthesis rate decreased. And apparent quantum yield was not indicated statistically significant difference from all treatment. Leaf area, leaf length and leaf width were significant higher in 35% shading and control under chestnut-leaf mold in all treatment. As the shading level increased, LAR (leaf area ratio), SLA (specific leaf area) and SPAD value decreased in pine-leaf mold and chestnut-leaf mold. As a result of surveying the whole experiment, P. japonicum is judged better growth and higher yield by maintaining 35% shading (relative light intensity 60%) under chestnut-leaf mold in forest farming.

• Design & Manufacturing
• /
• 제6권1호
• /
• pp.58-62
• /
• 2012

Unlike conventional single special cut methods, W-EDM is a combination of multiple-effects. This study focuses on the effects of second cut on the roughness of surfaces treated with W-EDM. W-EDM is, to a large extent, typical unmanned-machining equipment, which represents NC machining equipment that allows long-time full automation. W-EMD is getting popular as a precise machining technology and STD11 is frequently used in press die manufacture. In this study, the former is applied to the latter to look at the effects of second cut on the roughness of surfaces treated with W-EDM.

• 한국약용작물학회지
• /
• 제23권2호
• /
• pp.161-167
• /
• 2015

This study was carried out to determine the effects of light controls and leaf mold on root growth and physiological responses of Atractylodes japonica growing in forest farming. The experiment was performed by light controls (100%, 62.5%, 40.3% and 19.7% of full sunlight) and application of leaf mold to soil. Height, stem diameter, number of flower buds and root collar diameter were the highest in leaf mold within 62.5% of full sunlight (relative light intensity 62.5%). And these were the higher in leaf mold within each light level. As the shading level increased, light saturation point and maximum photosynthesis rate decreased. As the light level decreased, SPAD value increased in control and leaf mold. As a result of surveying the whole experiment, A. japonica was judged worse root growth under the lower light level. It was concluded that the light level was one of the most important factors to produce A. japonica. Also, producing high-quality of A. japonica with the price competitiveness by using leaf mold like the experiment can be an effective way to increase incomes for farmers.

• 소성∙가공
• /
• 제18권2호
• /
• pp.172-176
• /
• 2009

In this paper, new aspherical surface polishing mechanism is suggested to polish aspherical glass lens mold by both airbag polishing tool and reverse-rotational eccentric motion. Up to now, conventional aspherical lens polishing method by the small tool polishing uses the aspherical surface profile and the trajectory of the polishing tool is also controlled. However, full contact concept by airbag polishing tool and no position control make the easy polishing setup and does not need aspherical design profile. An aspherical lens polishing machine was made for this study and a tool mark removal experiment fur the fine-grounded lens mold was successfully performed.

• 한국산림과학회지
• /
• 제105권1호
• /
• pp.78-85
• /
• 2016

본 연구는 수요가 증가되고 있는 산채인 갯기름나물을 대상으로 임간재배지 내 차광과 부엽토가 갯기름나물의 생장 및 광합성 특성에 미치는 영향을 조사하여 보다 고품질의 갯기름나물을 생산하는 것뿐만 아니라 생산량 증대 및 친환경 재배기술 개발에 이바지하고자 하였다. 실험은 전광 및 35%, 50%, 75% 차광으로 총 4차광처리와 부엽토처리(대조구, 침엽부엽토, 활엽부엽토)를 하였다. 초장, 줄기직경, 근원직경, 줄기수, 건중량은 전광 내 활엽부엽토에서 가장 높았으며, 엽면적, 엽장, 엽폭은 35% 차광 내 활엽부엽토에서 가장 높았다. 광합성, 기공전도도, 증산율, 수분이용효율은 전광 내 활엽부엽토에서 가장 높았다. 특히, 광합성률은 모든 차광에서 활엽부엽토가 높게 조사되었으며, 차광률이 높아질수록 낮아지는 경향을 보였다. 따라서 갯기름나물을 친환경적으로 재배하기 위해서는 임간재배에서 35% 차광(상대광도 51.1%) 후 활엽부엽토를 이용하는 것이 가장 좋은 생장을 보여 생산량 증대와 고품질 갯기름나물의 생산에 가장 효과적일 것으로 판단된다.